EN ISO 1060-1:1999

Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 1060-1:1998)

Kunststoffe - Homo- und Copolymere des Vinylchlorids - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 1060-1:1998)

In diesem Teil von ISO 1060 wird ein Bezeichnungssystem für Vinylchlorid-Polymere festgelegt, das als Grundlage für Spezifikationen verwendet werden darf. Vinylchlorid-Polymere werden mit Hilfe eines Einleitungssystems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften:a) reduzierte Viskosität,b)Schüttdichte,c)Siebrückstand auf Drahtsiebboden mit 63 um lichter Maschenweite,d)Weichmacheraufnahme bei Raumtemperatur (nur für allgemein anwendbare G-Typen und Pastenverschnitt -F- Polymere), e) Viskosität und rheologische Charakteristik einer Standardpaste (nur für Pasten -P- Typen).

Plastiques - Résines d'homopolymères et de copolymères de chlorure de vinyle - Partie 1: Système de désignation et base de spécification (ISO 1060-1:1998)

La présente partie de l'ISO 1060 établit un système de désignation des résines thermoplastiques à base de chlorure de vinyle qui peut être utilisé comme base pour les spécifications. Les types de plastiques à base de chlorure de vinyle sont différenciés les uns des autres par un système de classification basé sur des niveaux appropriés des propriétés de désignation : a) viscosité réduite ; b) masse volumique apparente ; c) refus sur tamis de 63 pm d'ouverture de maille ; d) prise de plastifiant à la température ambiante (pour les résines pour usages généraux et les résines chargées, uniquement) ; e) viscosité et type de comportement rhéologique d'une pâte normalisée (pour les résines sous forme de pâtes, uniquement) ; et sur des informations concernant certains paramètres relatifs au polymère de base, les procédés de polymérisation et l'application prévue.

Polimerni materiali - Homo- in kopolimeri vinilklorida - 1. del: Sistem označevanja in podlage za specifikacije (ISO 1060-1:1998)

General Information

• Status: Withdrawn
• Publication Date: 18-May-1999
• Withdrawal Date: 23-Feb-2021
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/SC 1/WG 8 - Polyvinyls
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 24-Feb-2021
• Ref Project: SIST EN ISO 1060-1:2000 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 1060-1:1998)

Relations

• Replaced By: EN ISO 24024-1:2021 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 24024-1:2021)
• Effective Date: 02-Mar-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2000
3ROLPHUQLPDWHULDOL+RPRLQNRSROLPHULYLQLONORULGDGHO6LVWHPR]QDþHYDQMD
LQSRGODJH]DVSHFLILNDFLMH,62
Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation
system and basis for specifications (ISO 1060-1:1998)
Kunststoffe - Homo- und Copolymere des Vinylchlorids - Teil 1: Bezeichnungssystem
und Basis für Spezifikationen (ISO 1060-1:1998)
Plastiques - Résines d'homopolymeres et de copolymeres de chlorure de vinyle - Partie
1: Systeme de désignation et base de spécification (ISO 1060-1:1998)
Ta slovenski standard je istoveten z: EN ISO 1060-1:1999
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 1060-1
Second edition
1998-03-15
Plastics — Homopolymer and copolymer
resins of vinyl chloride —
Part 1:
Designation system and basis for
specifications
Plastiques — Résines d'homopolymères et de copolymères de chlorure de
vinyle —
Partie 1: Système de désignation et base de spécification
A
Reference number
ISO 1060-1:1998(E)
ISO 1060-1:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 1060-1 was prepared by Technical Committee
ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
This second edition cancels and replaces the first edition
(ISO 1060-1:1982) and includes the following main changes:
a) the viscosity and the type of rheological behaviour of standard pastes
have been introduced as designatory properties for paste resins;
b) retention on a 63 mm sieve has been introduced as a designatory
property;
c) plasticizer absorption has been introduced as a designatory property.
ISO 1060 consists of the following parts, under the general title Plastics —
Homopolymer and copolymer resins of vinyl chloride:
— Part 1: Designation system and basis for specifications
— Part 2: Preparation of test samples and determination of properties
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii
©
INTERNATIONAL STANDARD  ISO ISO 1060-1:1998(E)
Plastics — Homopolymer and copolymer resins of vinyl chloride —
Part 1:
Designation system and basis for specifications
1  Scope
1.1  This part of ISO 1060 establishes a system of designation for vinyl chloride thermoplastic resins, which may be
used as the basis for specifications.
1.2  The types of vinyl chloride plastics are differentiated from each other by a classification system based on
appropriate levels of the designatory properties:
a) reduced viscosity
b) apparent density
c) retention on a 63 mm mesh sieve
d) plasticizer absorption at room temperature (for general-purpose resins and filler resins only)
e) the viscosity and the type of rheological behaviour of a standard paste (for paste resins only)
and on information about basic polymer parameters, polymerization processes and intended applications.
1.3  This part of ISO 1060 is applicable to resins in powder form which consist of homopolymers of the monomer
vinyl chloride and copolymers, terpolymers, etc., of vinyl chloride with one or more other monomers, but where vinyl
chloride is the main constituent. The resins may contain small amounts of non-polymerized substances (e.g.
emulsifying or suspending agents, catalyst residues, etc.) and other substances added during the course of
polymerization.
1.4  It is not intended to imply that materials having the same designation give necessarily the same performance.
This part of ISO 1060 does not provide engineering data, performance data or data on processing conditions which
may be required to specify a material for a particular application and/or method of processing.
If such additional properties are required, they shall be determined in accordance with the test methods specified in
part 2 of this International Standard, if suitable.
1.5  In order to specify a resin for a particular application or to ensure reproducible processing, additional
requirements may be given in data block 5 (see clause 3, introductory paragraph).
2  Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part of
ISO 1060. At the time of publication, the editions indicated were valid. All standards are subject to revision, and
©
ISO
ISO 1060-1:1998(E)
parties to agreements based on this part of ISO 1060 are encouraged to investigate the possibility of applying the
most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid
International Standards.
ISO 1043-1:1997,
Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics.
ISO 1060-2:1998, Plastics — Homopolymer and copolymer resins of vinyl chloride — Preparation of test samples
and determination of properties.
3  Designation and specification system
The designation and specification system for thermoplastics is based on the following standardized pattern:
Designation
Identity block
Description International
Individual-item block
block Standard number
(optional) block Data block Data block Data block Data block Data block
1 2 3 4 5
The designation consists of an optional description block, reading “Thermoplastics”, and an identity block
comprising the International Standard number and an individual-item block. For unambiguous designation, the
individual-item block is subdivided into five data blocks providing the following information:
— Data block 1: Identification of the plastic by its symbol (PVC, etc.) in accordance with ISO 1043-1 and
information about the polymerization process and the composition of the polymer (see 3.1).
— Data block 2: Intended application (see 3.2).
— Data block 3: Designatory properties (see 3.3).
— Data block 4: Fillers or reinforcing materials and their nominal content (not included in this standard).
— Data block 5: For the purpose of specifications, a fifth data block may be added containing additional
information (see 3.4).
The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each
other by commas.
If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,,).
3.1  Data block 1
In this data block, after the hyphen, vinyl chloride polymer resins are identified by the symbol PVC or VC/./. for
homopolymers or copolymers/terpolymers respectively, in accordance with ISO 1043-1, followed, for
copolymers/terpolymers, by a space and by a two-figure number indicating the percentage content of combined
vinyl chloride. This is calculated from the chlorine content determined in accordance with ISO 1060-2, using the
equation
[VC] = 1,762 9 · [Cl]
After a hyphen, the polymerization process is indicated by a single code-letter as specified in table 1.
©
ISO
ISO 1060-1:1998(E)
Table 1 — Code-letters used for additional information in data block 1
Code-letter Definition
S
...