iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 7278-2:1995

(Main)

Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 2: Pipe provers (ISO 7278-2:1988)

Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 2: Pipe provers (ISO 7278-2:1988)

Provides guidance for the design, installation and calibration of these provers. Calculation techniques for use when calibrating and operating provers are detailed in ISO 4267-2. Most of the material is general in that it applies to provers for use with different liquids and types of meters and for proving them in different services. Does not apply to the newer "small volume" or "compact" provers.

Flüssige Kohlenwasserstoffe - Dynamische Messung - Prüfsysteme für volumetrische Meßgeräte - Teil 2: Rohrprüfer (ISO 7278-2:1988)

1.1 Dieser Teil von ISO 7278 behandelt Konstruktion, Installation und Kalibrierung von Rohrprüfern. Die Berechnungstechniken für das Kalibrieren und den Betrieb von Prüfern werden in ISO 4267-2 detailliert beschrieben. 1.2 Dieser Teil von ISO 7278 ist größtenteils allgemein gehalten im Hinblick auf Rohrprüfer, die bei unterschiedlichen Flüssigkeiten und Meßgerät-Typen benutzt und bei unterschiedlichen Betriebsabläufen geprüft werden können. Dieser Teil der Norm ISO 7278 bezieht sich nicht auf die neueren "Kleinvolumen" oder "Compact"Prüfer.

Hydrocarbures liquides - Mesurage dynamique - Systèmes d'étalonnage des compteurs volumétriques - Partie 2: Tubes étalons (ISO 7278-2:1988)

1.1 La présente partie de l'ISO 7278 donne des indications concernant la conception, l'installation et l'étalonnage des tubes étalons. Les calculs techniques nécessaires pour l'étalonnage et l'utilisation des tubes étalons sont détaillés dans l'ISO 4267-2. 1.2 La plupart des sujets abordés dans la présente partie de l'ISO 7278 sont de nature générale : ils s'appliquent aux tubes étalons destinés à être utilisés pour différents liquides et avec différents types de compteurs pour permettre un étalonnage dans différentes conditions de service. Cette méthode ne s'applique pas aux «petits volumes» ou appareils de vérification «compact» de conception récente. 1.3 Les conditions de référence pour la mesure des produits pétroliers sont la température à 15 °C et la pression égale à 101 325 Pa, telles que mentionnées dans l'ISO 5024.  
NOTE -- Dans certains pays, d'autres températures de référence sont utilisées (par exemple 20 °C et 60 °F).

Tekoči ogljikovodiki - Dinamična meritev - Sistemi za overjanje volumetrov - 2. del: Naprave za overjanje cevovodov (ISO 7278-2:1988)

General Information

Status
Withdrawn
Publication Date
03-Oct-1995
Withdrawal Date
29-Nov-2022
ICS
75.180.30 - Volumetric equipment and measurements
Technical Committee
CEN/TC 19 - Petroleum products, lubricants and related products
Drafting Committee
CEN/TC 19 - Petroleum products, lubricants and related products
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
30-Nov-2022
Ref Project
SIST EN ISO 7278-2:1998 - Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 2: Pipe provers (ISO 7278-2:1988)

Relations

Replaced By
EN ISO 7278-2:2022 - Petroleum measurement systems - Part 2: Pipe prover design, calibration and operation (ISO 7278-2:2022)
Effective Date
07-Dec-2022

Buy Standard

EN ISO 7278-2:1998EN ISO 7278-2:1998
PreviousNext
Standard
EN ISO 7278-2:1998
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 7278-2:1998
01-maj-1998
7HNRþLRJOMLNRYRGLNL'LQDPLþQDPHULWHY6LVWHPL]DRYHUMDQMHYROXPHWURYGHO
1DSUDYH]DRYHUMDQMHFHYRYRGRY ,62
Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters -
Part 2: Pipe provers (ISO 7278-2:1988)
Flüssige Kohlenwasserstoffe - Dynamische Messung - Prüfsysteme für volumetrische
Meßgeräte - Teil 2: Rohrprüfer (ISO 7278-2:1988)
Hydrocarbures liquides - Mesurage dynamique - Systemes d'étalonnage des compteurs
volumétriques - Partie 2: Tubes étalons (ISO 7278-2:1988)
Ta slovenski standard je istoveten z: EN ISO 7278-2:1995
ICS:
75.180.30 Oprema za merjenje Volumetric equipment and
prostornine in merjenje measurements
SIST EN ISO 7278-2:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 7278-2:1998

---------------------- Page: 2 ----------------------

SIST EN ISO 7278-2:1998

---------------------- Page: 3 ----------------------

SIST EN ISO 7278-2:1998

---------------------- Page: 4 ----------------------

SIST EN ISO 7278-2:1998

---------------------- Page: 5 ----------------------

SIST EN ISO 7278-2:1998

---------------------- Page: 6 ----------------------

SIST EN ISO 7278-2:1998
ISO
INTERNATIONAL STANDARD
7278-2
First edition
1988-12-15
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION
ORGANISATION INTERNATIONALE DE NORMALISATION
MEXJ/YHAPOJJHAFl OPTAHM3A~Mfl I-IO CTAH,4APTM3A~MM
Liquid hydrocarbons - Dynamit measurement -
Proving Systems for volumetric meters -
Part 2:
Pipe provers
S ystkmes d% talonnage des comp teurs
Hydrocarbures liquides - Mesurage dynamique -
volume triques
Partie 2: Tubes t+talons
Reference number
ISO 7278-2 : 1988 (E)

---------------------- Page: 7 ----------------------

SIST EN ISO 7278-2:1998
ISO 7278-2 : 1988 (El
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of
national Standards bodies (ISO member bodies). T.he work of preparing International
Standards is normally carried out through ISO technical committees. Esch member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the ISO Council. They are approved in accordance with ISO procedures requiring at
least 75 % approval by the member bodies voting.
International Standard ISO 7278-2 was prepared by Technical Committee ISO/TC 28,
Petroleum produc ts and lubrican ts.
Users should note that all International Standards undergo revision from time to time
and that any reference made herein to any other International Standard implies its
latest edition, unless otherwise stated.
0 International Organkation for Standardkation, 1988
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 7278-2:1998
ISO 7278-2 : 1988 (EI
Page
Contents
1
.........................................................
0 Introduction
1
..........................................
1 Scope and field of application
1
2 References .
1
3 Definitions. .
2
................................................
4 Description of Systems
3
....................................
5 Essential Performance requirements.
3
6 Equipment .
5
7 Design of pipe provers .
7
8 Installation .
7
9 Calibration .
Annexes
............................. 15
A The use of pipe provers with four detectors
........ 18
Example of the calculation of the design Parameters of a pipe prover
B
Figures
12
..........................
1 Typical unidirectional return-type prover System
13
....................
2 Typical bidirectional straight-type Piston prover System
14
.........................
3 Typical bidirectional U-type sphere prover System
17
..............
4 Simultaneous use of two counters with a four-detector prover
17
...................
5 Temnorarv connection of counters to measure nl and n7
. . .
Ill

---------------------- Page: 9 ----------------------

SIST EN ISO 7278-2:1998
This page intentionally left blank

-------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 12185:2024(Main)
Crude petroleum, petroleum products and related products - Determination of density - Laboratory density meter with an oscillating U tube sensor (ISO 12185:2024)
SIST EN ISO 12185:2024

This document specifies a method for the determination, using an oscillating U-tube density meter, of the density of crude petroleum and related products within the range 600 kg/m3 to 1 100 kg/m3, which can be handled as single-phase liquids at the test temperature and pressure.
This document is applicable to liquids of any vapour pressure as long as suitable precautions are taken to ensure that they remain in single phase. Loss of light components leads to changes in density during both the sample handling and the density determination.
This method is not intended for use with in-line density meters.

  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7278-2:2022(Main)
Petroleum measurement systems - Part 2: Pipe prover design, calibration and operation (ISO 7278-2:2022)
SIST EN ISO 7278-2:2023

This document provides descriptions of the different types of pipe provers, otherwise known as displacement provers, currently in use. These include sphere (ball) provers and piston provers operating in unidirectional and bidirectional forms. It applies to provers operated in conventional, reduced volume, and small volume modes.
This document gives guidelines for:
—    the design of pipe provers of each type;
—    the calibration methods;
—    the installation and use of pipe provers of each type;
—    the interaction between pipe provers and different types of flowmeters;
—    the calculations used to derive the volumes of liquid measured (see Annex A);
—    the expected acceptance criteria for fiscal and custody transfer applications, given as guidance for both the calibration of pipe provers and when proving flowmeters (see Annex C).
This document is applicable to the use of pipe provers for crude oils and light hydrocarbon products which are liquid at ambient conditions. The principles apply across applications for a wider range of liquids, including water. The principles also apply for low vapour pressure, chilled and cryogenic products, however use with these products can require additional guidance.

  • Standard
    118 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8222:2020/A1:2022(Amendment)
Petroleum measurement systems - Calibration - Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) - Amendment 1: Correction of two typographical errors (ISO 8222:2020/Amd 1:2022)
SIST EN ISO 8222:2020/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8222:2020(Main)
Petroleum measurement systems - Calibration - Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) (ISO 8222:2020)
SIST EN ISO 8222:2020

This document describes the design, use and calibration of volumetric measures (capacity measures) which are intended for use in fixed locations in a laboratory or in the field. This document gives guidance on both standard and non-standard measures. It also covers portable and mobile measures. This document is applicable to the petroleum industry; however, it may be applied more widely to other applications.
This document excludes measures for cryogenic liquids and pressurized measures as used for liquid petroleum gas (LPG) and liquefied natural gas (LNG).
Volumetric measures are classified as test measures or prover tanks depending on capacity and design.
Measures described in this document are primarily designed, calibrated and used to measure volumes from a measure which is wetted and drained for a specified time before use and designated to deliver. Many of the provisions, however, apply equally to measures which are used to measure a volume using a clean and dry measure and designated to contain.
Guidance is given regarding commonly expected uncertainties and calibration specifications.
The document also provides, in Annex A, reference formulae describing the properties of water and other fluids and materials used in volumetric measurement more generally.

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8311:2013(Main)
Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels - Calibration of membrane tanks and independent prismatic tanks in ships - Manual and internal electro-optical distance-ranging methods (ISO 8311:2013)
SIST EN ISO 8311:2014

ISO 8311:2013 specifies a method for the internal measurement of membrane tanks used in ships for the transport of refrigerated light hydrocarbon fluids. In addition to the actual process of measurement, it sets out the calculation procedures for compiling the tank capacity table and correction tables to be used for the computation of cargo quantities. ISO 8311:2013, with some modification, can also be applicable to the calibration of independent prismatic tanks.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7278-1:1995(Main)
Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 1: General principles (ISO 7278-1:1987)
SIST EN ISO 7278-1:1998

The purpose of proving a meter is to determine its relative error or its meter factor as a function of flow rate and other parameters such as temperature, pressure and viscosity. The following types of proving systems are in use: tank prover systems; pipe provers, bidirectional and unidirectional; master meters. They can be used either connected (fixed or mobile) to the metering station or in a central proving station.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4267-2:1995(Main)
Petroleum and liquid petroleum products - Calculation of oil quantities - Part 2: Dynamic measurement (ISO 4267-2:1988)
SIST EN ISO 4267-2:1998

Defines the various terms employed in the calculation of metered petroleum quantities. Also specifies the equations which allow the values of correction factors to be computed. Also gives rules for the sequence, rounding and significant figures to be employed in a calculation. Provides tables which may be used to look up specific correction factors should it not be desired to calculate them by manual as well as computer methods. The field of application is the volumetric measurement of liquid hydrocarbons, including liquefied petroleum gases, by meter and prover. It does not include two-phase fluids.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6551:1995(Main)
Petroleum liquids and gases - Fidelity and security of dynamic measurement - Cabled transmission of electric and/or elecronic pulsed data (ISO 6551:1982)
SIST EN ISO 6551:1998

Establishes guidelines for ensuring the quantities stated, a main objective being to ensure the integrity of the primary indication. In order to achieve different levels of security, criteria and recommendations for the design, installation, use and maintenance of the relevant equipment are laid down. Regulatory requirements, including those for safety, are not specifically covered in detail but certain general cautionary notes on safety are included for guidance.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12185:2024(Main)
Crude petroleum, petroleum products and related products - Determination of density - Laboratory density meter with an oscillating U tube sensor (ISO 12185:2024)
SIST EN ISO 12185:2024

This document specifies a method for the determination, using an oscillating U-tube density meter, of the density of crude petroleum and related products within the range 600 kg/m3 to 1 100 kg/m3, which can be handled as single-phase liquids at the test temperature and pressure.
This document is applicable to liquids of any vapour pressure as long as suitable precautions are taken to ensure that they remain in single phase. Loss of light components leads to changes in density during both the sample handling and the density determination.
This method is not intended for use with in-line density meters.

  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7278-2:2022(Main)
Petroleum measurement systems - Part 2: Pipe prover design, calibration and operation (ISO 7278-2:2022)
SIST EN ISO 7278-2:2023

This document provides descriptions of the different types of pipe provers, otherwise known as displacement provers, currently in use. These include sphere (ball) provers and piston provers operating in unidirectional and bidirectional forms. It applies to provers operated in conventional, reduced volume, and small volume modes.
This document gives guidelines for:
—    the design of pipe provers of each type;
—    the calibration methods;
—    the installation and use of pipe provers of each type;
—    the interaction between pipe provers and different types of flowmeters;
—    the calculations used to derive the volumes of liquid measured (see Annex A);
—    the expected acceptance criteria for fiscal and custody transfer applications, given as guidance for both the calibration of pipe provers and when proving flowmeters (see Annex C).
This document is applicable to the use of pipe provers for crude oils and light hydrocarbon products which are liquid at ambient conditions. The principles apply across applications for a wider range of liquids, including water. The principles also apply for low vapour pressure, chilled and cryogenic products, however use with these products can require additional guidance.

  • Standard
    118 pages
    English language
    sale 10% off
    e-Library read for
    1 day