EN 415-7:2006

Safety of packaging machines - Part 7: Group and secondary packaging machines

This European Standard applies to the following groups of machines:
Group and secondary packaging machines and the collating systems associated with them.
The individual machines are described in 3.2 of this European Standard.
This European Standard deals with safety requirements for machine design, construction, installation, commissioning, operation, adjustment, maintenance and cleaning of group and secondary packaging machines.
The extent to which hazards, hazardous situations and events are covered, are indicated in Clause 4.
Exclusions
This European Standard is not applicable to the following machines:
¾   machines that were manufactured before the date of publication of this document by CEN;
¾   strapping machines. These machines are covered by EN 415-8;
¾   crate loaders and un-loaders for pre-formed rigid containers. These machines are covered by
EN 415-2;
¾   cartoning machines. Cartoning machines are covered by EN 415-3.
This European Standard does not consider the following hazards:
¾   use of group and secondary packaging machines in potentially explosive atmospheres;
¾   health, safety or hygiene hazards associated with the products that may be handled by the machines, but does include general advice on this subject;
¾   hazards that may be associated with electromagnetic emissions from group and secondary packaging machines;
¾   hazards that may be associated with decommissioning group and secondary packaging machines.

Sicherheit von Verpackungsmaschinen - Teil 7: Sammelpackmaschinen

Diese Europäische Norm behandelt folgende Maschinengruppen:
Sammelpackmaschinen und die mit ihnen verbundenen Gruppiersysteme.
Die einzelnen Maschinenarten werden in 3.2 dieser Norm beschrieben.
Diese Europäische Norm beschreibt Sicherheitsanforderungen für Gestaltung, Bau, Installation, Inbetrieb¬nahme, Betrieb, Einstellung, Instandhaltung und Reinigung von Sammelpackmaschinen.
Der Umfang der behandelten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse ist in Abschnitt 4 angegeben.
Ausnahmen
Diese Europäische Norm ist nicht anwendbar auf folgende Maschinen:
-   Maschinen, die vor der Veröffentlichung dieses Dokuments durch CEN hergestellt wurden;
-   Umreifungsmaschinen. Diese Maschinen werden in EN 415-8 behandelt;
-   Kasten-Einpack- und Auspackmaschinen für vorgefertigte formstabile Packmittel. Diese Maschinen werden in EN 415-2 behandelt;
-   Kartoniermaschinen. Kartoniermaschinen werden in EN 415-3 behandelt.
Diese Europäische Norm berücksichtigt folgende Gefährdungen nicht:
-   Den Einsatz von Sammelpackmaschinen in explosionsgefährdeten Atmosphären;
-   Gefährdungen für Gesundheit, Sicherheit oder Hygiene, die sich durch die Produkte ergeben, die von den Maschinen verarbeitet werden. Jedoch werden allgemeine Hinweise zu diesem Thema gegeben;
-   Gefährdungen durch elektromagnetische Emissionen von Sammelpackmaschinen;
-   Gefährdungen, die sich bei der Außerbetriebnahme von Sammelpackmaschinen ergeben können.

Sécurité des machines d'emballage - Partie 7: Machines de groupe et d'emballage secondaire

La présente Norme européenne s’applique aux groupes de machines suivants :
Machines de groupe et d’emballage secondaire, et systèmes de groupage leur étant spécialement associés.
Les machines sont décrites de manière individuelle en 3.2 de la présente Norme européenne.
La présente Norme européenne concerne les exigences de sécurité pour la conception, la construction, l’installation, la mise en service, le fonctionnement, le réglage, la maintenance et le nettoyage des machines de groupe et d’emballage secondaire.
L’étendue des phénomènes, situations et événements dangereux couverts est indiquée dans l’Article 4.

Pakirne naprave – Varnost pakirnih naprav – 7. del: Zbirni in dodatni pakirni stroji

General Information

• Status: Withdrawn
• Publication Date: 11-Jul-2006
• Withdrawal Date: 01-Jul-2008
• ICS: 55.020 - Packaging and distribution of goods in general
• Technical Committee: CEN/TC 146 - Packaging machines - Safety
• Drafting Committee: CEN/TC 146/WG 7 - Group packaging machines
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 02-Jul-2008
• Completion Date: 02-Jul-2008
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Ref Project: SIST EN 415-7:2007 - Safety of packaging machines - Part 7: Group and secondary packaging machines

Relations

• Merged Into: EN 415-7:2006+A1:2008 - Safety of packaging machines - Part 7: Group and secondary packaging machines
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Safety of packaging machines - Part 7: Group and secondary packaging machinesPakirne naprave – Varnost pakirnih naprav – 7. del: Zbirni in dodatni pakirni strojiSécurité des machines d'emballage - Partie 7: Machines de groupe et d'emballage secondaireSicherheit von Verpackungsmaschinen - Teil 7: SammelpackmaschinenTa slovenski standard je istoveten z:EN 415-7:2006SIST EN 415-7:2007en55.200Pakirni strojiPackaging machineryICS:SLOVENSKI
STANDARDSIST EN 415-7:200701-januar-2007

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 415-7July 2006ICS 55.020 English VersionSafety of packaging machines - Part 7: Group and secondarypackaging machinesSécurité des machines d'emballage - Partie 7: Machines degroupe et d'emballage secondaireSicherheit von Verpackungsmaschinen - Teil 7:SammelpackmaschinenThis European Standard was approved by CEN on 20 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 415-7:2006: E

EN 415-7: 2006 (E) 2 Contents Page Foreword.7 Introduction.8 1 Scope.9 2 Normative references.9 3 Terms and definitions.13 3.1 Definition of terms.13 3.2 Description of group and secondary packaging machines.15 3.2.1 Machines for erecting packaging materials.15 3.2.2 Product loading/unloading machines.17 3.2.3 Machines for sealing packages.20 3.2.4 Group package form, fill and seal machines.24 4 Hazards on group and secondary packaging machines.29 4.1 General.29 4.2 General group and secondary packaging machine hazards.30 4.2.1 General.30 4.2.2 Mechanical hazards.30 4.2.3 Electrical hazards.31 4.2.4 Thermal hazards.31 4.2.5 Noise.31 4.2.6 Hazards from products and materials.31 4.2.7 Hazards due to neglecting ergonomic principles.32 4.2.8 Hazards caused by failures.32 4.2.9 Hazards due to neglecting hygienic design principles.33 4.2.10 Common mechanisms on group and secondary packaging machines.33 4.3 Hazards associated with a tray erecting machine.34 4.3.1 General.34 4.3.2 Tray blank magazine.35 4.3.3 Tray blank extracting mechanism.35 4.3.4 Tray blank transport mechanism.35 4.3.5 Forming assembly.36 4.3.6 Discharge mechanism.36 4.4 Hazards associated with case erecting machines.36 4.4.1 General.36 4.4.2 Hazards associated with a semi-automatic case erector.36 4.4.3 Hazards associated with a fully automatic case erector.36

EN 415-7: 2006 (E) 4 5.2.5 Noise reduction.60 5.2.6 Measures to control hazards generated by products and materials.61 5.2.7 Ergonomic design principles.62 5.2.8 Requirements to prevent hazards caused by failures.63 5.2.9 Hygienic design requirements.65 5.2.10 Requirements for mechanisms used on most group and secondary packaging machines.66 5.3 Safety requirements for a tray erecting machine.68 5.3.1 General.68 5.3.2 Tray blank magazine.68 5.3.3 Tray blank extracting mechanism.69 5.3.4 Tray blank transport mechanism.69 5.3.5 Forming assembly.69 5.3.6 Discharge mechanism.69 5.4 Safety requirements for a case erecting machine.69 5.4.1 Safety requirements for a semi-automatic case erector.69 5.4.2 Safety requirements for a fully automatic case erector.
...