CEN/TS 14159:2004
(Main)Textile floor coverings - Requirements for tolerances on (linear) dimensions of rugs, runners, carpet tiles and wall-to-wall carpet and for tolerances on pattern repeat
Textile floor coverings - Requirements for tolerances on (linear) dimensions of rugs, runners, carpet tiles and wall-to-wall carpet and for tolerances on pattern repeat
This standard specifies the maximum accepted tolerances on the dimensions and distortions in pattern, of rugs, runners, carpet tiles and wall-to-wall carpet.
NOTE These tolerances do not affect the functional characteristics of the floor covering
Textile Bodenbeläge - Anforderungen an Toleranzen der (linearen) Maße von abgepassten Teppichen, Läufern, Teppichfliesen und Teppich-Auslegware und des Musterrapports
Dieses Dokument legt die größten zulässigen Abweichungen in den Maßen und die größten zulässigen Musterverzerrungen von abgepassten Teppichen, Läufern, Teppichfliesen und Teppich Auslegware fest.
ANMERKUNG Diese Abweichungen beeinflussen nicht die Funktionseigenschaften des Bodenbelags.
Revêtements de sol textiles - Exigences concernant les tolérances sur les dimensions (linéaires) des tapis, passages, dalles de moquette et moquettes et les tolérances sur le raccord de dessin
Le présent document spécifie les tolérances maximales acceptées sur les dimensions et les déformations du
dessin des tapis, passages, dalles de moquette et moquettes.
NOTE Ces tolérances n�influent pas sur les caractéristiques fonctionnelles du revêtement de sol.
Tekstilne talne obloge – Dovoljene tolerance (linearnih) dimenzij preprog, tekačev, plošč in talnih oblog za popolno pokritje tal (od zidu do zidu) ter tolerance za ponovljivost vzorca
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2005
7HNVWLOQHWDOQHREORJH±'RYROMHQHWROHUDQFH OLQHDUQLK GLPHQ]LMSUHSURJWHNDþHY
SORãþLQWDOQLKREORJ]DSRSROQRSRNULWMHWDO RG]LGXGR]LGX WHUWROHUDQFH]D
SRQRYOMLYRVWY]RUFD
Textile floor coverings - Requirements for tolerances on (linear) dimensions of rugs,
runners, carpet tiles and wall-to-wall carpet and for tolerances on pattern repeat
Textile Bodenbeläge - Anforderungen an Toleranzen der (linearen) Maße von
abgepassten Teppichen, Läufern, Teppichfliesen und Teppich-Auslegware und des
Musterrapports
Revetements de sol textiles - Exigences concernant les tolérances sur les dimensions
(linéaires) des tapis, passages, dalles de moquette et moquettes et les tolérances sur le
raccord de dessin
Ta slovenski standard je istoveten z: CEN/TS 14159:2004
ICS:
59.080.60 Tekstilne talne obloge Textile floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION
CEN/TS 14159
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
December 2004
ICS 59.080.60
English version
Textile floor coverings - Requirements for tolerances on (linear)
dimensions of rugs, runners, carpet tiles and wall-to-wall carpet
and for tolerances on pattern repeat
Revêtements de sol textiles - Exigences concernant les Textile Bodenbeläge - Anforderungen an Toleranzen der
tolérances sur les dimensions (linéaires) des tapis, (linearen) Maße von abgepassten Teppichen, Läufern,
passages, dalles de moquette et moquettes et les Teppichfliesen und Teppich-Auslegware und des
tolérances sur le raccord de dessin Musterrapports
This Technical Specification (CEN/TS) was approved by CEN on 26 June 2004 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 14159:2004: E
worldwide for CEN national Members.
Contents Page
1 Scope .5
2 Normative references .6
3 Terms and definitions .6
4 Apparatus .7
5 Procedure .7
6 Required tolerances and deviations.11
Foreword
This document (CEN/TS 14159:2004) has been prepared by Technical Committee CEN/TC 134 “Resilient,
textile and laminate floor coverings”, the secretariat of which is held by BSI.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this CEN Technical Specification: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
Introduction
Owing to influences of the production process on the structure, textile floor coverings may
show variations in size and distortion. However, in many cases, certain discrepancies can be
worked away through professional and careful installation. By open communication between
manufacturer and installer, an agreement can be found between what is technically possible
in manufacturing, and at the same time technically workable during Installation.
The maximum distortions in pattern repeat specified in this Technical Specification are
applicable only to carpets with certain design styles ex-factory.
1 Scope
This document specifies the maximum accepted tolerances on the dimensions and distortions in pattern, of
rugs, runners, carpet tiles and wall-to-wall carpet.
NOTE These tolerances do not affect the functional characteristics of the floor covering
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 994, Textile floor coverings -Determination of the size length, squareness and straightness of tiles
EN 1307, Textile floor coverings – Classification of pile carpets
EN 1470, Textile floor coverings – Classification of needled floor coverings except for needled pile floor
coverings
EN 13297, Textile floor coverings –Classification of needled pile floor coverings
EN 14215, Textile floor coverings – Classification of machine made pile rugs and runners
ISO 2424:1992, Textile floor coverings – vocabulary
lSO 3018, Textile floor coverings – Rectangular textile floor coverings -Determination of dimensions
3 Terms and definitions
For the purposes of this document the terms and definitions in ISO 2424:1992 and the following apply:
3.1 arcing (Carpet roll)
Arcing of the carpet roll itself in the production direction when unrolled (Figure 5)
3.2 linear pattern distortion (in direction
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.