EN 2436-005:2006
(Main)Aerospace series - Paints and varnishes - Corrosion resistant chromate-free two component cold curing primer - Part 005: For exterior use with surface preparation tolerance
Aerospace series - Paints and varnishes - Corrosion resistant chromate-free two component cold curing primer - Part 005: For exterior use with surface preparation tolerance
This standard specifies the basic requirements for a two component, cold curing, chromate-free epoxy or polyurethane, corrosion resistant primer which can be used with or without a finish for aerospace applications.
The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837, process D and ISO 3270. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met.
Luft- und Raumfahrt - Beschichtungsstoffe - Korrosionsbeständiger Zweikomponenten-Primer, kalthärtend, chromatfrei - Teil 005: Außenanwendung mit Oberflächentoleranzen
Diese Norm legt die Mindestanforderungen an einen korrosionsbeständigen, chromatfreien, kalthärtenden Zweikomponenten Primer auf Epoxid oder Polyurethanharzbasis fest, der mit oder ohne Deckbeschichtung in der Luft und Raumfahrt verwendet werden kann.
Die in dieser Norm festgelegten Eigenschaften werden anhand definierter Probenkörper aus Aluminiumlegie¬rung ermittelt, die nach EN 3837, Verfahren D und ISO 3270 vorbereitet werden. Die Eignung des für eine bestimmte Anwendung zu verwendenden Materials (z. B. alternativer Trägerwerkstoff, alternativer Primer, bestimmte Trocknungsbedingungen usw.) ist durch zusätzliche Prüfungen bestimmen, um nachzuweisen, dass die Anforderungen dieser Norm erfüllt werden.
Série aérospatiale - Peintures et vernis - Peintures primaire anti-corrosion sans chromate à deux composants polymérisant à température ambiante - Partie 005 : Pour extérieur avec tolérance à la préparation de surface
Aeronavtika - Barve in laki - Dvokomponentni temeljni premaz, korozijsko obstojen, brez kroma, ki se suši pri sobni temperaturi - 005. del: Za zunanjo uporabo, s toleranco pri pripravi površine
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Barve in laki - Dvokomponentni temeljni premaz, korozijsko obstojen, brez kroma, ki se suši pri sobni temperaturi - 005. del: Za zunanjo uporabo, s toleranco pri pripravi površineLuft- und Raumfahrt - Beschichtungsstoffe - Korrosionsbeständiger Zweikomponenten-Primer, kalthärtend, chromatfrei - Teil 005: Außenanwendung mit OberflächentoleranzenSérie aérospatiale - Peintures et vernis - Peintures primaire anti-corrosion sans chromate à deux composants polymérisant à température ambiante - Partie 005 : Pour extérieur avec tolérance à la préparation de surfaceAerospace series - Paints and varnishes - Corrosion resistant chromate-free two component cold curing primer - Part 005: For exterior use with surface preparation tolerance49.040Prevleke in z njimi povezani postopki, ki se uporabljajo v letalski in vesoljski industrijiCoatings and related processes used in aerospace industryICS:Ta slovenski standard je istoveten z:EN 2436-005:2006SIST EN 2436-005:2009en,de01-julij-2009SIST EN 2436-005:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2436-005July 2006ICS 49.040 English VersionAerospace series - Paints and varnishes - Corrosion resistantchromate-free two component cold curing primer - Part 005: Forexterior use with surface preparation toleranceSérie aérospatiale - Peintures et vernis - Peinturesprimaires anti-corrosion sans chromate à deux composantspolymérisant à température ambiante - Partie 005 : Pourextérieur avec tolérance à la préparation de surfaceLuft- und Raumfahrt - Anstrichstoffe -Korrosionsbeständiger Zweikomponenten-Grundanstrich,kalthärtend chromatfrei - Teil 005: Außenanwendung mitOberflächentoleranzenThis European Standard was approved by CEN on 9 March 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2436-005:2006: ESIST EN 2436-005:2009
EN 3837, Aerospace series — Paints and varnishes — Nature and method for surface preparation of test pieces in aluminium alloys1) EN 2434-004, Aerospace series — Paints and varnishes — Two component cold curing polyurethane finish — Part 004: High flexibility2) EN 3840, Aerospace series — Paints and varnishes — Technical specification1) EN 4385, Aerospace series — Non-metallic materials — General organisation of standardisation — Links be-tween types of standards1) ISO 1513,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.