FprEN 1991-4
(Main)Eurocode 1 - Actions on structures - Part 4: Silos and tanks
Eurocode 1 - Actions on structures - Part 4: Silos and tanks
1.1 Scope of EN 1991-4
(1) EN 1991-4 provides rules for calculating actions for the structural design of silos and tanks.
NOTE 1 Silos are used for the storage of particulate solids. Tanks are used for the storage of liquids.
NOTE 2 For limitations on rules for silos given in this document, see 1.3.
NOTE 3 For limitations on rules for tanks given in this document, see 1.4.
(2) EN 1991-4 includes some provisions for actions on silo and tank structures that are not only associated with the stored particulate solids or liquids (e.g. the effects of thermal differentials) but substantially affected by them.
NOTE Liquid loads on tanks are very precisely defined. Many loads on silos are not known with great precision. This document provides guidance for many practical situations for which very limited certain knowledge is available, and the information is derived from the limited experimental and analytical information available, coupled with conclusions drawn from failure investigations. The information is not based on a sound statistical treatment of experimental data.
(3) EN 1991-4 is intended for use with concrete, steel, aluminium, timber and FRP storage structures.
NOTE FRP is the standard acronym for fibre reinforced polymer materials.
(4) EN 1991-4 is also applicable for the structural assessment of existing silos and tanks, unless otherwise specified by the relevant authority or, if not specified, agreed between the relevant parties for the specific project.
NOTE 1 Changes in filling or discharge arrangements, changes in the wall friction of inner surfaces, or in the use of the silo, including storage of different particulate solids, can be reasons for assessing existing silos.
NOTE 2 Differentiation of the liquid stored can be a reason for assessing existing tanks.
1.2 Assumptions
(1) The assumptions of EN 1990 apply.
(2) EN 1991-4 is intended to be used in conjunction with EN 1990, with the other parts of EN 1991, EN 1992, EN 1993, EN 1995, EN 1997, EN 1998 and EN 1999 where relevant to the design of silos and tanks.
1.3 Limitations on silos
1.3.1 Geometrical limitations
(1) The following geometrical limitations apply to the design rules for silos and silo batteries (see 3.2.59 and 3.2.60) covered by this document:
- the silo planform cross-section shapes are limited to those shown in Figure 1.1c.
NOTE 1 Further information concerning planform cross-section geometries is given in Clause 7.
NOTE 2 For the determination of the effective diameter dc of the silo see Figure 1.1c;
- the following dimensional limitations on the aspect ratio for free-standing single cell silos hc/dc, the overall height hb and the effective diameter dc apply (see Figure 1.1):
hc/dc < 10 (1.1)
hb < 100 m (1.2)
dc < 60 m (1.3)
NOTE 3 See Figure 1.1 for hc, dc and hb.
- the structural transition lies in a single horizontal plane (see Figure 1.1a);
...
Eurocode 1 - Einwirkungen auf Tragwerke - Teil 4: Einwirkungen auf Silos und Flüssigkeitsbehälter
1.1 Anwendungsbereich von EN 1991-4
(1) EN 1991-4 enthält Regeln für die Berechnung von Einwirkungen auf Silos und Flüssigkeitsbehälter für die Tragwerksplanung.
ANMERKUNG 1 Silos werden für die Lagerung von Schüttgütern verwendet. Flüssigkeitsbehälter werden für die Lagerung von Flüssigkeiten verwendet.
ANMERKUNG 2 Eingrenzungen der in diesem Dokument enthaltenen Regeln für Silos siehe 1.3.
ANMERKUNG 3 Eingrenzungen der in diesem Dokument enthaltenen Regeln für Flüssigkeitsbehälter siehe 1.4.
(2) EN 1991-4 enthält auch einige Bestimmungen für Einwirkungen auf Silos und Flüssigkeitsbehälter, die nicht nur in Zusammenhang mit den gelagerten Schüttgütern oder Flüssigkeiten stehen (z. B. Auswirkungen von Temperaturunterschieden), sondern die wesentlich von ihnen beeinflusst werden.
ANMERKUNG Die von Flüssigkeiten auf Flüssigkeitsbehälter ausgeübten Lasten sind sehr präzise definiert. Viele auf Silos wirkende Lasten sind nicht mit hoher Genauigkeit bekannt. Dieses Dokument bietet einen Leitfaden für zahlreiche praktische Situationen, in denen nur sehr wenig gesichertes Wissen vorhanden ist und die Informationen aus den verfügbaren begrenzten experimentellen und analytischen Informationen in Kombination mit Schlussfolgerungen aus der Untersuchung von Versagensfällen abgeleitet werden. Die Informationen basieren nicht auf einer robusten statistischen Verarbeitung experimenteller Daten.
(3) EN 1991-4 ist für Lagerbauwerke aus Beton, Stahl, Aluminium, Holz und FKV vorgesehen.
ANMERKUNG FKV ist das Standardakronym für Faser-Kunststoff-Verbundwerkstoffe.
(4) EN 1991-4 ist ebenfalls anwendbar für die Tragwerksbewertung bestehender Silos und Flüssigkeitsbehälter, sofern nicht anders von der zuständigen Behörde festgelegt oder, sofern keine Festlegungen getroffen wurden, für das jeweilige Projekt zwischen den beteiligten Parteien vereinbart.
ANMERKUNG 1 Gründe für die Bewertung bestehender Silos können Änderungen der Bedingungen bei Füllen oder Entleeren, der Wandreibung der inneren Oberflächen oder der Verwendung des Silos, einschließlich der Lagerung unterschiedlicher Schüttgüter, sein.
ANMERKUNG 2 Differenzierung der gelagerten Flüssigkeit kann ein Grund für die Bewertung bestehender Flüssigkeitsbehälter sein.
1.2 Annahmen
(1) Es gelten die Annahmen von EN 1990.
(2) EN 1991-4 ist im Zusammenhang mit EN 1990, mit den weiteren Teilen der Reihen EN 1991, EN 1992, EN 1993, EN 1995, EN 1997, EN 1998 und EN 1999, sofern für die Bemessung von Silos und Flüssigkeitsbehältern maßgebend, anwendbar.
1.3 Eingrenzungen bei Silos
1.3.1 Geometrische Eingrenzungen
(1) Für die Anwendung der Bemessungsregeln für die von diesem Dokument behandelten Silos und Silobatterien (siehe 3.2.59 und 3.2.60) gelten folgende geometrische Eingrenzungen:
- die Siloquerschnittsformen sind auf die in Bild 1.1c gezeigten begrenzt.
ANMERKUNG 1 Weitere Informationen zu Querschnittsgeometrien sind in Abschnitt 7 enthalten.
ANMERKUNG 2 Zur Bestimmung des effektiven Silodurchmessers dc siehe Bild 1.1c.
- es gelten die folgenden Maßgrenzen für die Schlankheit bei freistehenden Einzelzellensilos hc/dc, die Gesamthöhe hb und den effektiven Durchmesser dc (siehe Bild 1.1):
hc/dc < 10 (1.1)
hb < 100 m (1.2)
dc < 60 m (1.3)
ANMERKUNG 3 Siehe Bild 1.1 zu hc, dc und hb.
- der Tragwerksübergang vom vertikalen Siloschaft in den Trichter erfolgt in einer einzigen horizontalen Ebene (siehe Bild 1.1a).
...
Eurocode 1 - Actions sur les structures - Partie 4 : Actions sur les silos et les réservoirs
1.1 Domaine d'application de l'EN 1991 4
(1) L'EN 1991 4 donne des recommandations pour calculer les actions pour le calcul structural des silos et des réservoirs.
NOTE 1 Les silos sont utilisés pour le stockage des matières granulaires. Les réservoirs sont utilisés pour le stockage des liquides.
NOTE 2 Pour les limites des règles relatives aux silos données dans le présent document, voir 1.3.
NOTE 3 Pour les limites des règles relatives aux réservoirs données dans le présent document, voir 1.4.
(2) L'EN 1991 4 contient aussi certaines indications concernant les actions sur les structures des silos et réservoirs qui ne sont pas liées aux matières ou aux liquides stockés (par exemple les effets thermiques différentiels), mais qui sont considérablement affectées par eux.
NOTE Les charges de liquides sur les réservoirs sont définies de manière très précise. De nombreuses charges sur les silos ne sont pas connues avec grande précision. La présente norme fournit des recommandations pour de nombreuses situations pratiques pour lesquelles les connaissances certaines sont très limitées, et les informations sont dérivées des informations expérimentales et analytiques limitées disponibles, associées à des conclusions tirées d'analyses de défaillances. Les informations ne sont pas basées sur un traitement statistique solide de données expérimentales.
(3) L'EN 1991 4 est destinée à être utilisée pour les structures de stockage en béton, en acier, en aluminium, en bois et en FRP (« fibre reinforced polymer »).
NOTE FRP est l'acronyme normalisé pour les matériaux polymères renforcés de fibres.
(4) Il est permis d'utiliser l'EN 1991 4 pour l'évaluation structurale d'une construction existante, pour le calcul de réparations et de modifications, et l'appréciation de changements d'utilisation.
NOTE Lorsque l'évaluation structurale d'une structure existante est envisagée, il peut être fait référence à l'Annexe Nationale et au client concernant la pertinence de la norme actuelle.
1.2 Hypothèses
(1) Les hypothèses données dans l'EN 1990 s'appliquent.
(2) L'EN 1991 4 est destinée à être utilisée conjointement avec l'EN 1990, et les autres parties de l'EN 1991, de l'EN 1992, de l'EN 1993, de l'EN 1995, de l'EN 1997, de l'EN 1998 et de l'EN 1999 lorsqu'elles sont pertinentes pour le calcul des silos et des réservoirs.
Evrokod 1 - Vplivi na konstrukcije - 4. del: Silosi in rezervoarji
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 1991-4:2024
01-junij-2024
Nadomešča:
SIST EN 1991-4:2006
Evrokod 1 - Vplivi na konstrukcije - 4. del: Silosi in rezervoarji
Eurocode 1 - Actions on structures - Part 4: Silos and tanks
Eurocode 1 - Einwirkungen auf Tragwerke - Teil 4: Einwirkungen auf Silos und
Flüssigkeitsbehälter
Eurocode 1 - Actions sur les structures - Partie 4 : Actions sur les silos et les réservoirs
Ta slovenski standard je istoveten z: prEN 1991-4
ICS:
23.020.10 Nepremične posode in Stationary containers and
rezervoarji tanks
91.010.30 Tehnični vidiki Technical aspects
oSIST prEN 1991-4:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 1991-4:2024
oSIST prEN 1991-4:2024
DRAFT
EUROPEAN STANDARD
prEN 1991-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2024
ICS 91.010.30 Will supersede EN 1991-4:2006
English Version
Eurocode 1 - Actions on structures - Part 4: Silos and tanks
Eurocode 1 - Actions sur les structures - Partie 4 : Silos Eurocode 1 - Einwirkungen auf Tragwerke - Teil 4:
et réservoirs Einwirkungen auf Silos und Flüssigkeitsbehälter
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 250.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1991-4:2024 E
worldwide for CEN national Members.
oSIST prEN 1991-4:2024
prEN 1991-4:2024 (E)
Contents Page
European foreword . 7
0 Introduction . 8
1 Scope .10
1.1 Scope of EN 1991-4 .10
1.2 Assumptions .10
1.3 Limitations on silos.10
1.3.1 Geometrical limitations . 10
1.3.2 Limitations on the stored solids . 13
1.3.3 Limitations on filling and discharge arrangements . 14
1.4 Limitations on tanks .15
2 Normative references .16
3 Terms, definitions and symbols .16
3.1 General .16
3.2 Terms and definitions.16
3.3 Symbols and abbreviations.25
3.3.1 Roman upper-case letters . 25
3.3.2 Roman lower-case letters . 26
3.3.3 Greek upper-case letters . 29
3.3.4 Greek lower-case letters . 29
4 Classification of silos .30
4.1 Action Assessment Classes for silos . 30
4.2 Silo usage classes . 33
5 Design situations and modelling of actions .33
5.1 General .33
5.2 Representation of loads on silos .33
5.2.1 Genera l . 33
5.2.2 Representation of loads on silo inside surfaces . 34
5.2.3 Classification of actions on silos . 34
5.2.4 Evaluation of loads on silos . 35
5.2.5 Silo Fundamental and Special load cases . 36
5.2.6 Design situations for specific silo construction forms . 37
5.3 Evaluation of filling and discharge conditions for silos .38
5.3.1 General . 38
5.3.2 Prediction of symmetrical flow patterns . 41
5.3.3 Assessment of the filling and discharge eccentricities . 43
5.3.4 Silos storing powders . 46
5.4 Silo Fundamental Load Cases (SFLC) .46
5.4.1 Common failure modes . 46
5.4.2 Eccentricity limits for Silo Fundamental Load Cases . 47
5.4.3 Uncertainty and variability of solid properties . 47
5.4.4 Types of Silo Fundamental Load Cases . 48
5.5 Silo Special Load Cases (SSLC) .49
5.5.1 General . 49
5.5.2 Situations that require Silo Special Load Cases . 50
5.5.3 Unsymmetrical discharge . 50
5.5.4 Eccentricity limits . 53
5.5.5 Large eccentricity filling loads in slender and very slender circular silos . 54
5.5.6 Large eccentricity filling loads in squat and intermediate slenderness circular silos . 54
5.5.7 Moderate eccentricity discharge loads in slender and very slender circular silos . 54
5.5.8 Moderate eccentricity discharge loads in squat and intermediate slenderness circular silos54
5.5.9 Large eccentricity pipe flow in circular and rectangular silos . 55
oSIST prEN 1991-4:2024
prEN 1991-4:2024 (E)
5.5.10 Silos containing solids with entrained air . 55
5.5.11 Thermal differences between stored solids and the silo structure . 55
5.5.12 Suction due to inadequate venting . 56
5.5.13 Loads on the vertical walls of special rectangular silos . 56
5.5.14 Internal inverted cone . 56
5.5.15 Oblique conical hoppers . 56
5.5.16 Eccentric pipe flow in steep concentric or oblique hoppers . 57
5.5.17 Principles for design of silos against dust explosions . 57
5.6 Load modifying factors for direct use in load evaluations . 58
5.7 Representation of loads on tanks . 59
6 Properties of particulate solids . 60
6.1 General. 60
6.1.1 Flow Group . 60
6.1.2 Properties of solids for design calculations . 60
6.1.3 Wall Friction Category . 60
6.1.4 Characteristic values of material properties . 62
6.1.5 Applications of the effective modulus . 63
6.2 Particulate solid properties: principles and background . 64
6.2.1 General . 64
6.2.2 Obtaining appropriate solids properties for design . 65
6.3 Testing particulate solids . 66
6.3.1 Test procedures . 66
6.3.2 Bulk unit weight γ . 66
6.3.3 Coefficient of wall friction μ . 66
6.3.4 Angle of internal friction ϕi . 67
6.3.5 Lateral pressure ratio K .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.