EN 10363:2016

Continuously hot-rolled patterned steel strip and plate/sheet cut from wide strip - Tolerances on dimensions and shape

This European Standard specifies tolerances on dimensions and shape for continuously hot-rolled uncoated patterned steel strip and plate/sheet cut of it in nominal thicknesses up to 20 mm inclusive, of non-alloy and alloy steels in accordance with Table 1 (see also Annex A).
(...)
Steel grades other than those given in Table 1 may be used by agreement only.
This European standard does not apply to stainless steels.

Kontinuierlich warmgewalztes Riffelband und -blech abgelängt aus Warmbreitband aus Stahl - Grenzabmaße und Formtoleranzen

Diese Europäische Norm legt die Grenzabmaße und Formtoleranzen für kontinuierlich warmgewalztes Band und Blech ohne Überzug, in Nenndicken bis einschließlich 20 mm, aus unlegierten und legierten Stählen nach Tabelle 1 (siehe Anhang A), fest.
Weitere Stahlsorten als in der Tabelle 1 angegeben, dürfen nur nach Vereinbarung geliefert werden.
Diese Europäische Norm gilt nicht für nichtrostende Stähle.

Bandes et tôles/feuilles larmées striées issues de larges bandes en acier laminé à chaud en continu - tolérances sur les dimensions et la forme

Cette norme européenne spécifie les tolérances sur les dimensions et la forme des bande laminés à chaud en continu non revêtues avec des motifs et les tôles/feuilles issues de celles-ci dans des épaisseurs allant jusqu'à 20 mm inclus, en aciers non alliés et aciers alliés, conformément au Tableau 1 (voir aussi l'Annexe A).
Les nuances d'acier autres que celles données dans le Tableau 1 ne peuvent être utilisées que suite à un accord.
Cette norme européenne ne s'applique pas aux aciers inoxydables.

Kontinuirno vroče valjani vzorčasti jekleni trakovi in trakovi brez prevleke - Mejni odstopki mer in tolerance oblik

Ta evropski standard določa tolerance mer in oblik za vroče valjane reliefne jeklene trakove brez prevleke in iz njih izrezane plošče/pločevine z največjo širino 2200 mm in debelinami do 20 mm iz nelegiranega in legiranega jekla.

General Information

• Status: Published
• Publication Date: 19-Jul-2016
• Withdrawal Date: 30-Jan-2017
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: ECISS/TC 103 - Structural steels other than reinforcements
• Drafting Committee: ECISS/TC 103/WG 4 - Hot-rolled patterned steel strip and plate/sheet
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 15-Mar-2022
• Completion Date: 14-Apr-2025
• Ref Project: SIST EN 10363:2016 - Continuously hot-rolled patterned steel strip and plate/sheet cut from wide strip - Tolerances on dimensions and shape

Overview

EN 10363:2016 (CEN) defines tolerances on dimensions and shape for continuously hot-rolled, uncoated patterned steel strip and sheets/plates cut from wide strip (nominal thicknesses up to 20 mm). It applies to non‑alloy and alloy steels referenced to EN 10025 series and EN 10149‑2 (see Annex A) and explicitly excludes stainless steels. The standard covers form of supply, surface design options (designs T, R, A), pattern height ranges and the dimensional tolerances that manufacturers, purchasers and inspectors must use.

Key topics and technical requirements

• Scope and materials: Applies to patterned ("chequer" or "bulb") hot‑rolled strip and cut sheets/plates up to 20 mm nominal thickness; other steel grades permitted only by agreement.
• Product information to supply: quantity, product type (wide strip, sheet/plate, slit strip), EN number, surface design symbol (T/R/A), nominal thickness, width, length, steel grade, edge‑camber requirements for slit strips.
• Pattern dimensions: Pattern height h specified by nominal thickness - for t ≥ 3.0 mm: h = 1.0–2.2 mm; for t < 3.0 mm: h = 0.5–2.2 mm.
• Thickness tolerances: Tabled by nominal thickness; tolerances increase with thickness (examples given in EN 10363 Table 2).
• Width tolerances: Normal tolerances typically 0 / +20 mm for widths < 1 500 mm and 0 / +5 mm for widths ≥ 1 500 mm; special tighter tolerances (trimmed edges) available by agreement for thin products.
• Length tolerances: e.g., +20 mm for lengths < 4 000 mm, +30 mm for 4 000–6 000 mm, +40 mm for 6 000–8 000 mm (longer lengths by agreement).
• Flatness, edge camber and out‑of‑squareness: Flatness limits depend on nominal thickness and width (see Table 5). Edge camber and out‑of‑squareness are specified (e.g., edge camber limits for sheets/plates and strip, superimposition option by agreement).
• Testing and inspection: Measurement points and procedures are defined - thickness measured outside patterned zones and minimum edge distances (40 mm for mill edges, 25 mm for trimmed edges). Measurements for dispute must be at ambient temperature.

Applications and practical use

EN 10363:2016 is used to specify and verify dimensional quality of patterned steel used for:

• Industrial flooring, stair treads, platforms and ramps (non‑slip surfaces)
• Vehicle decks, loading platforms and walkways
• Structural and architectural panels where patterned surfaces are required

Using EN 10363 ensures compatibility between mills, distributors, fabricators and purchasers by providing consistent tolerances on thickness, width, length, flatness and edge geometry.

Who uses this standard

• Steel producers and rolling mills (product specification and quality control)
• Steel service centres and distributors (acceptance and stock control)
• Fabricators, architects and specifiers (material selection)
• Inspection bodies and testing laboratories (conformity testing)

Related standards

• EN 10025 series (structural steels)
• EN 10149‑2 (high‑strength steels)
• EN 10020, EN 10079 (definitions and steel product terminology)

Keywords: EN 10363:2016, patterned steel strip, hot‑rolled patterned steel, tolerances, thickness tolerances, width tolerances, flatness, edge camber, sheet/plate.

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kontinuierlich warmgewalztes Riffelband und -blech abgelängt aus Warmbreitband - Grenzabmaße und FormtoleranzenContinuously hot-rolled patterned steel strip and plate/sheet cut from wide strip - Tolerances on dimensions and shape77.140.50SROL]GHONLFlat steel products and semi-products17.040.10Tolerance in ujemiLimits and fitsICS:Ta slovenski standard je istoveten z:EN 10363:2016SIST EN 10363:2016en,fr,de01-oktober-2016SIST EN 10363:2016SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10363
July
t r s x ICS
y yä s v rä w r English Version
Continuously hotærolled patterned steel strip and dimensions and shape larges bandes en acier laminß à chaud en continu æ tolßrances sur les dimensions et la forme
Kontinuierlich warmgewalztes Riffelband und æblech abgelängt aus Warmbreitband aus Stahl æ Grenzabmaße und Formtoleranzen This European Standard was approved by CEN on
s w April
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r u x uã t r s x ESIST EN 10363:2016

Standards with steel grades for this dimensional standard . 14 Annex B (informative)
Indicative typical weight . 15 Bibliography . 16
· 600 mm)a Sheet/plate cut from wide strip Strip w < 600 mm slit from wide strip
¶ 20 mm EN 10025–2 EN 10025–3 EN 10025–4 EN 10025–5 EN 10149–2 a Usually these steel products are delivered in widths up to and including 2 200 mm. For widths values w over 2 200 mm, see 4.2, Option 4.
Steel grades other than those given in Table 1 may be used by agreement only. This European standard does not apply to stainless steels. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020:2000, Definition and classification of grades of steel EN 10079:2007, Definition of steel products 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10020:2000, EN 10079:2007 and the following apply. 3.1 hot-rolled patterned steel strip hot-rolled steel strip which has been provided with a regular raised pattern (chequer or bulb) on one side to render the surface more non-slip and safer underfoot, with the reverse side usually smooth 4 Information to be supplied by the purchaser 4.1 General The following information shall be supplied by the purchaser at the time of enquiry and order: a) quantity to be supplied; b) product designation (wide strip, sheet/plate cut from wide strip, strip slit from wide strip); c) the number of this standard (EN 10363); SIST EN 10363:2016
...