EN 10051:2024
(Main)Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
This document specifies tolerances on dimensions and shape for continuously hot-rolled uncoated plate/sheet and strip with a maximum width of 2 200 mm and a maximum thickness of 25 mm of non-alloy and alloy steels in accordance with Table 1 (see also Annex B). This document also applies to hot-rolled strip for cold rolling.
Table 1 - Field of application
[...table not represented...]
NOTE 1 This document does not apply to:
- hot-rolled strip rolled in widths w < 600 mm (see EN 10048);
- hot-rolled patterned steel strip and plate/sheet cut from wide strip (EN 10363);
- uncoated or electrolytically coated cold rolled sheet and strip (see EN 10131);
- hot-dip coated steel sheet and strip (EN 10143);
- stainless steels.
NOTE 2 This document can also be used for steels from other standards, e. g. steels for shipbuilding.
Kontinuierlich warmgewalztes Band und Tafel/Blech abgelängt aus Warmbreitband aus unlegierten und legierten Stählen - Grenzabmaße und Formtoleranzen
Dieses Dokument legt die Grenzabmaße und Formtoleranzen für kontinuierlich warmgewalzte, unbeschichtete Tafeln/Bleche und Bänder mit einer maximalen Breite von 2 200 mm und einer maximalen Dicke von 25 mm aus unlegierten und legierten Stählen nach Tabelle 1 (siehe auch Anhang B) fest. Dieses Dokument ist auch anwendbar für warmgewalztes Band zum Kaltwalzen.
Tabelle 1 — Anwendungsbereich
Erzeugnis Dicke Stahlsorten nach:
mm (aber nicht beschränkt darauf)
- Breitband (Breite 600 mm ≤ w ≤ 2 200 mm),
- Blech/Tafel geschnitten aus Breitband,
- aus Breitband längsgeteiltes Band (Breite w < 600 mm) ≤ 25 mm EN 10025 2 bis EN 10025−6 Konstruktionsstähle
EN 10028 2 bis EN 10028−6 Stähle für Druckanwendungen
EN ISO 683 1 und EN ISO 683 2 Stähle zum Vergüten
EN ISO 683 3 Einsatzstähle
EN ISO 683 5 Nitrierstähle
EN 10111 Bleche und Bänder aus kohlenstoffarmen Stählen zum Kaltumformen
EN 10120 Stahlbleche und -bänder für geschweißte Gasflaschen
EN 10149 2 und EN 10149−3 Stähle mit hoher Streckgrenze zum Kaltumformen
EN 10207 Stähle für einfache Druckbehälter
EN 10225 1 Bleche für feste Offshore-Strukturen
EN 10338 Nicht beschichtete Erzeugnisse aus Mehrphasenstählen zur Kaltumformung
EN ISO 4957 Werkzeugstähle
Dieses Dokument ist nicht anwendbar für:
- warmgewalztes Band in Walzbreiten w < 600 mm (siehe EN 10048).
- warmgewalztes Profilstahlband und von Breitband abgelängtes Blech (siehe EN 10363);
- unbeschichtetes oder elektrolytisch beschichtetes kaltgewalztes Blech und Band (siehe EN 10131);
- schmelztauchveredeltes Stahlblech und -band (EN 10143);
- Nichtrostende Stähle.
Dieses Dokument kann auch für Stähle anderer Normen angewendet werden, z. B. für Stähle für den Schiffbau.
Bandes laminées à chaud en continu et tôles issues de larges bandes en aciers alliés et non alliés - Tolérances sur les dimensions et la forme
Le présent document spécifie les tolérances sur les dimensions et la forme des bandes, des feuilles et tôles non revêtues, laminées à chaud en continu, d’une largeur maximale de 2 200 mm et une épaisseur maximale de 25 mm, en aciers alliés et non alliés, conformément au Tableau 1 (voir également l’Annexe B). Le présent document s’applique également aux bandes laminées à chaud destinées au laminage à froid.
Tableau 1 - Domaine d’application
[table not represented]
NOTE 1 Le présent document ne s’applique pas :
- aux bandes laminées à chaud, en largeurs w < 600 mm (voir EN 10048) ;
- aux bandes et tôles et feuilles larmées striées issues de larges bandes en acier larmé laminé à chaud (voir EN 10363) ;
- aux tôles et bandes laminées à froid non revêtues ou revêtues par voie électrolytique (voir EN 10131) ;
- aux tôles et bandes en acier revêtues par immersion à chaud (EN 10143) ;
- aux aciers inoxydables.
NOTE 2 Le présent document peut également être appliqué aux aciers provenant d'autres normes, par exemple les aciers pour la construction navale.
Kontinuirno vroče valjane pločevine in trakovi iz legiranih in nelegiranih jekel brez prevleke - Tolerance mer in oblik
Ta dokument določa tolerance mer in oblik za kontinuirno vroče valjane pločevine in trakove brez prevleke z največjo širino 2200 mm in največjo debelino 25 mm iz legiranih in nelegiranih jekel v skladu s preglednico 1 (glej tudi dodatek B). Ta dokument se uporablja tudi za vroče valjane trakove, namenjene za hladno valjanje.
Preglednica 1 – Področje uporabe
[... preglednica ni prikazana ...]
OPOMBA 1: Ta dokument se ne uporablja za:
– vroče valjane trakove z valjano širino < 600 mm (glej standard EN 10048);
– vroče valjane vzorčaste jeklene pločevine in trakove iz širokih trakov (EN 10363);
– hladno valjane pločevine in trakove brez prevleke oziroma z elektrolitsko prevleko (glej standard EN 10131);
– vroče prevlečene jeklene pločevine in trakove (EN 10143);
– nerjavna jekla.
OPOMBA 2: Ta dokument je mogoče uporabiti tudi za jekla iz drugih standardov (npr. jekla v ladjedelništvu).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2024
Kontinuirno vroče valjane pločevine in trakovi iz legiranih in nelegiranih jekel brez
prevleke - Tolerance mer in oblik
Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy
steels - Tolerances on dimensions and shape
Kontinuierlich warmgewalztes Band und Blech abgelängt aus Warmbreitband aus
unlegierten und legierten Stählen - Grenzabmaße und Formtoleranzen
Bandes et tôles issues de bandes refendues laminées à chaud en continu, en aciers
alliés - Tolérances sur les dimensions et la forme
Ta slovenski standard je istoveten z: EN 10051:2024
ICS:
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 10051
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2024
EUROPÄISCHE NORM
ICS 77.140.50 Supersedes EN 10051:2010
English Version
Continuously hot-rolled strip and plate/sheet cut from
wide strip of non-alloy and alloy steels - Tolerances on
dimensions and shape
Bandes laminées à chaud en continu et tôles issues de Kontinuierlich warmgewalztes Band und Blech
larges bandes en aciers alliés et non alliés - Tolérances abgelängt aus Warmbreitband aus unlegierten und
sur les dimensions et la forme legierten Stählen - Grenzabmaße und Formtoleranzen
This European Standard was approved by CEN on 27 February 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10051:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Information to be supplied by the purchaser . 5
4.1 General. 5
4.2 Options . 5
4.3 Designation . 6
5 Form of supply . 6
6 Tolerances for sheet/plate . 6
6.1 Thickness . 6
6.2 Length. 9
6.3 Width . 9
6.4 Flatness . 10
6.5 Edge camber . 10
6.6 Out-of-squareness . 10
6.7 Superimposement of dimensions . 10
7 Tolerances for wide strip and strip slit from wide strip . 11
7.1 General. 11
7.2 Thickness . 12
7.3 Width . 12
7.4 Edge camber . 12
8 Measurement . 13
8.1 General. 13
8.2 Thickness . 13
8.3 Length of sheet/plate . 13
8.4 Width . 13
8.5 Flatness for sheet/plate . 13
8.6 Edge camber . 14
8.7 Out-of-squareness for sheet/plate . 15
Annex A (normative) Thickness tolerances with only positive tolerances according to
Option 3 . 16
Annex B (informative) Standards with steel grades for this dimensional standard . 19
European foreword
This document (EN 10051:2024) has been prepared by Technical Committee CEN/TC 459/SC 3
“Structural steels other than reinforcements”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2024, and conflicting national standards shall
be withdrawn at the latest by January 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10051:2010.
In comparison with the previous edition EN 10051:2010, the following technical modifications have been
made:
— tolerances on flatness were revised;
— options were revised, a new option for only positive thickness tolerances was introduced and the
options were moved from Annex B to 4.2;
— thickness tolerances for strip and sheet/plate with minimum yield strength > 960 MPa must be
agreed;
— flatness measurement revised;
— change regarding the tolerances of cropped coils;
— editorial revisions.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
1 Scope
This document specifies tolerances on dimensions and shape for continuously hot-rolled uncoated
plate/sheet and strip with a maximum width of 2 200 mm and a maximum thickness of 25 mm of non-
alloy and alloy steels in accordance with Table 1 (see also Annex B). This document also applies to hot-
rolled strip for cold rolling.
Table 1 — Field of application
Thickness Steel grades according to:
Product
mm (but not limited to)
EN 10025-2 to −6 Structural steels
EN 10028-2 to −6 Steels for pressure purposes
EN ISO 683-1 and 683-2 Steels for quenching and tempering
• wide strip
EN ISO 683-3 Case hardening steels
(width:
600 mm ≤ w ≤
EN ISO 683-5 Nitriding steels
2 200 mm),
EN 10111 Low carbon steel sheet and strip for cold forming
• sheet/plate cut
from wide strip,
≤ 25 mm
EN 10120 Steel sheet and strip for welded gas cylinders
• strip
EN 10149-2 and −3 High yield strength steels for cold forming
(width:
w < 600 mm slit
EN 10207 Steels for simple pressure vessels
from wide strip)
EN 10225-1 Plates for fixed offshore structures
Non-coated products of multiphase steels for cold
EN 10338
forming
EN ISO 4957 Tool steels
This document does not apply to:
— hot-rolled strip rolled in widths w < 600 mm (see EN 10048);
— hot-rolled patterned steel strip and plate/sheet cut from wide strip (see EN 10363);
— uncoated or electrolytically coated cold rolled sheet and strip (see EN 10131);
— hot-dip coated steel sheet and strip (EN 10143);
— stainless steels.
This document can also be used for steels from other standards, e.g. steels for shipbuilding.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10020, Definition and classification of grades of steel
EN 10079, Definition of steel products
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10020, EN 10079 and the
following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
non-alloy and alloy steels
steels, alloy and non-alloy, which follow the information and requirements outlined in EN 10020
3.2
wide strip and sheet/plate
steels in wide strip, sheet or plate format, which follow the information, requirements and test methods
outlined in EN 10079
3.3
crown
difference in thickness between one of the edges and the centre of a rolled product
4 Information to be supplied by the purchaser
4.1 General
The following information shall be supplied by the purchaser at the time of enquiry and order:
a) the quantity to be delivered;
b) designation of the product (wide strip, sheet/plate cut from wide strip, strip slit from wide strip);
c) number of this dimensional standard (EN 10051);
d) nominal thickness and width in mm;
e) nominal length in mm (for sheet and plate);
f) upper width tolerances for sheet/plate with thickness > 15 mm (see 6.3);
g) tolerances on flatness for sheet/plate of thickness ≤ 3 mm of category D (see 6.4 and Table 9);
h) edge camber requirements for strip < 600 mm wide, which was slit from wide strip (see 7.4).
4.2 Options
A number of options are specified in this document and listed below. If the purchaser does not indicate
his wish to implement any of these options, the supplier shall supply in accordance with the basic
specification of this document (see 4.1 and 5.1):
1) whether trimmed edges (T) or mill edges (M) are required, otherwise the edge condition is at the
discretion of the manufacturer (see 5.1);
2) whether coils may be delivered with welded seams (see 5.2);
3) whether the minimum thickness of the product shall be the nominal thickness and the full range of
the thickness tolerance from Tables 3 to 6 (disposition of tolerances) shall be valid only as a positive
tolerance (see 6.1.2 and Annex A);
4) whether thickness and/or flatness tolerances of steel grades with a minimum specified yield
strength > 960 MPa need to be agreed (see 6.1.2);
5) whether for sheet/plate special tolerances on flatness are required (see 6.4 and Table 9);
6) whether for sheet/plate the tolerances o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.