EN 1440:2008
(Main)LPG equipment and accessories - Periodic inspection of transportable refillable LPG cylinders
LPG equipment and accessories - Periodic inspection of transportable refillable LPG cylinders
This European Standard specifies procedures for periodic inspection and testing, for transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l.
This standard is applicable to the following:
welded and brazed steel LPG cylinders with a specified minimum wall thickness (see EN 1442 and EN 12807 or the equivalent standard);
welded steel LPG cylinders without specified minimum wall thickness (see EN 14140:2003+A1 or the equivalent standard);
welded aluminium LPG cylinders (see EN 13110 or the equivalent standard);
composite LPG cylinders (see EN 14427 or the equivalent standard).
This standard is intended to be applied to cylinders complying with RID/ADR (including pi marked cylinders) and also to existing non RID/ADR cylinder populations.
This standard does not apply to cylinders permanently installed in vehicles.
Flüssiggas-Geräte und Ausrüstungsteile - Wiederkehrende Prüfung von ortsbeweglichen, wiederbefüllbaren Flaschen für Flüssiggas (LPG)
Diese Europäische Norm legt Verfahren für die wiederkehrende Prüfung von ortsbeweglichen, wieder¬befüll¬baren Flaschen für Flüssiggas (LPG) mit einem Fassungsraum von 0,5 l bis einschließlich 150 l fest.
Diese Norm gilt für:
geschweißte und gelötete Flaschen aus Stahl für Flüssiggas (LPG) mit festgelegter Mindest-Wanddicke (siehe EN 1442 und EN 12807 oder gleichwertige Norm);
geschweißte Flaschen aus Stahl für Flüssiggas (LPG) ohne festgelegte Mindest-Wanddicke (siehe EN 14140:2003+A1 oder gleichwertige Norm);
geschweißte Flaschen aus Aluminium für Flüssiggas (LPG) (siehe EN 13110 oder gleichwertige Norm);
Flüssiggasflaschen aus Verbundwerkstoff (siehe EN 14427 oder gleichwertige Norm).
Diese Norm ist für Flaschen vorgesehen, die RID/ADR entsprechen (einschließlich Flaschen mit Pi Kenn¬zeichnung) sowie für bestehende Flaschengruppen, die nicht mit RID/ADR übereinstimmen.
Diese Norm gilt nicht für Flaschen, die dauerhaft in Fahrzeugen eingebaut sind.
Equipement et accessoires GPL - Contrôle périodique des bouteilles de GPL transportables et réutilisables
Cette Norme européenne spécifie des modes opératoires pour des contrôles et des essais périodiques pour des bouteilles pour GPL rechargeables et transportables d’une capacité en eau comprise entre 0,5 et 150 l.
Cette norme s’applique aux éléments suivants :
bouteilles pour GPL en acier soudées et brasées avec une épaisseur de paroi minimale précisée (voir l’EN 1442 et EN 12807 et norme équivalente) ;
bouteilles pour GPL en acier soudées et brasées sans épaisseur de paroi minimale précisée (voir l’EN 14140:2003+A1 ou une norme équivalente) ;
bouteilles pour GPL en aluminium soudées (voir l’EN 13110 ou une norme équivalente) ;
bouteilles pour GPL en matériaux composites (voir l’EN 14427 ou une norme équivalente).
Il est prévu d’appliquer cette norme à des bouteilles conformes au RID/ADR (y compris les bouteilles comportant un marquage pi), ainsi qu’aux familles de bouteilles existantes non-conformes aux RID/ADR
Cette norme ne s’applique pas aux bouteilles installées en permanence dans des véhicules.
Oprema in pribor za utekočinjeni naftni plin (UNP) - Periodični pregledi premičnih, ponovno polnljivih jeklenk za UNP
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flüssiggas-Geräte und Ausrüstungsteile - Wiederkehrende Prüfung von ortsbeweglichen, wiederbefüllbaren Flaschen für Flüssiggas (LPG)Bouteilles en acier soudé transportables et rechargeables pour gaz de pétrole liquéfié (GPL) - Requalification périodiqueLPG equipment and accessories - Periodic inspection of transportable refillable LPG cylinders23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN 1440:2008SIST EN 1440:2008en,fr,de01-junij-2008SIST EN 1440:2008SLOVENSKI
STANDARDSIST EN 14795:20061DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1440February 2008ICS 23.020.30Supersedes EN 1440:2005, EN 14767:2005, EN14795:2005, EN 14914:2005
English VersionLPG equipment and accessories - Periodic inspection oftransportable refillable LPG cylindersBouteilles en acier soudé transportables et rechargeablespour gaz de pétrole liquéfié (GPL) - RequalificationpériodiqueFlüssiggas-Geräte und Ausrüstungsteile - WiederkehrendePrüfung von ortsbeweglichen, wiederbefüllbaren Flaschenfür Flüssiggas (LPG)This European Standard was approved by CEN on 6 January 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1440:2008: ESIST EN 1440:2008
Specific requirements for welded and brazed steel LPG cylinders.16 Annex B (normative)
Specific requirements for welded steel LPG cylinders in accordance with EN 14140:2003+A1 or the equivalent standard.18 B.1 General.18 B.2 Procedure for establishing rejection criteria carbon steel cylinders.18 B.3 Rejection criteria for stainless steel cylinders.20 Annex C (normative)
Specific requirements for welded aluminium LPG cylinders.23 Annex D (normative)
Specific requirements for composite LPG cylinders.25 D.1 Establishment of rejection criteria.25 D.1.1 General.25 D.1.2 Procedure.25 D.2 Examples of rejection criteria.26 Annex E (normative)
Requirements for 15-year periodic inspection interval for welded and brazed steel cylinders.32 SIST EN 1440:2008
Guidance on requirements for 10-year periodic inspection interval on composite cylinders.34 Annex G (normative)
Periodic inspection procedure for a particular design of protected cylinder.35 G.1 Scope and cylinder description.35 G.2 Cylinders design and manufacturing requirements.36 G.2.1 Steel cylinder.36 G.2.2 External protection.36 G.2.3 Marking and recording requirements.36 G.3 Inspection at filling.36 G.4 Periodic destructive tests on batch sampling.36 G.4.1 Testing procedure.36 G.4.2 Destructive tests.37 G.4.3 Rejection criteria and batch sampling.37 G.4.4 Periodic inspection tests reports and records.37 Bibliography.38
Therefore the standards listed in the normative references and covering basic requirements of the RID/ADR not addressed within the present standard are normative only when the standards themselves are referred to in the RID and/or in the technical annexes of the ADR. The main changes between this version of the standard and the 2005 version is that this version combines EN 1440:2005, EN 14767:2005, EN 14795:2005 and EN 14914:2005 into a single standard. This European Standard supersedes EN 1440:2005, EN 14767:2005, EN 14795:2005 and EN 14914:2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 1440:2008
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.