EN ISO 6507-4:2005

Metallic materials - Vickers hardness test - Part 4: Tables and hardness values (ISO 6507-4:2005)

ISO 6507-4:2005 gives tables of Vickers hardness for use in tests made on flat surfaces.

Metallische Werkstoffe - Härteprüfung nach Vickers - Teil 4: Tabellen zur Bestimmung der Härtewerte (ISO 6507-4:2005)

In diesem Teil von ISO 6507 ist das Verfahren für die Kalibrierung von Härtevergleichsplatten, die bei der indirekten Prüfung von Härteprüfmaschinen nach Vickers nach ISO 6507-2 verwendet werden, festgelegt.
Das Verfahren ist nur anwendbar für Eindrücke mit Diagonalenlängen ³ 0,020 mm.

Matériaux métalliques - Essai de dureté Vickers - Partie 4: Tableaux des valeurs de dureté (ISO 6507-4:2005)

L'ISO 6507-4:2005 donne les Tableaux de dureté Vickers pour utilisation lors d'essais réalisés sur surfaces planes.

Kovinski materiali – Preskus trdote po Vickersu – 4. del: Tabela za določanje trdote (ISO 6507-4:2005)

General Information

• Status: Withdrawn
• Publication Date: 14-Dec-2005
• Withdrawal Date: 20-Mar-2018
• ICS: 77.040.10 - Mechanical testing of metals
• Technical Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Drafting Committee: ECISS/TC 1 - Steel - Mechanical testing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 21-Mar-2018
• Ref Project: SIST EN ISO 6507-4:2006 - Metallic materials - Vickers hardness test - Part 4: Tables and hardness values (ISO 6507-4:2005)

Relations

• Replaced By: EN ISO 6507-4:2018 - Metallic materials - Vickers hardness test - Part 4: Tables of hardness values (ISO 6507-4:2018)
• Effective Date: 18-Sep-2013

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2006
.RYLQVNLPDWHULDOL±3UHVNXVWUGRWHSR9LFNHUVX±GHO7DEHOD]DGRORþDQMH
WUGRWH,62
Metallic materials - Vickers hardness test - Part 4: Tables and hardness values (ISO
6507-4:2005)
Metallische Werkstoffe - Härteprüfung nach Vickers - Teil 4: Tabellen zur Bestimmung
der Härtewerte (ISO 6507-4:2005)
Matériaux métalliques - Essai de dureté Vickers - Partie 4: Tableaux des valeurs de
dureté (ISO 6507-4:2005)
Ta slovenski standard je istoveten z: EN ISO 6507-4:2005
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 6507-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 77.040.10
English Version
Metallic materials - Vickers hardness test - Part 4: Tables and
hardness values (ISO 6507-4:2005)
Matériaux métalliques - Essai de dureté Vickers - Partie 4: Metallische Werkstoffe - Härteprüfung nach Vickers - Teil
Tableaux des valeurs de dureté (ISO 6507-4:2005) 4: Tabellen zur Bestimmung der Härtewerte (ISO 6507-
4:2005)
This European Standard was approved by CEN on 14 December 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6507-4:2005: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 6507-4:2005) has been prepared by Technical Committee ISO/TC 164
"Mechanical testing of metals" in collaboration with Technical Committee ECISS/TC 1 "Steel -
Mechanical testing", the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2006, and conflicting national
standards shall be withdrawn at the latest by June 2006.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 6507-4:2005 has been approved by CEN as EN ISO 6507-4:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 6507-4
First edition
2005-12-15
Metallic materials — Vickers hardness
test —
Part 4:
Tables of hardness values
Matériaux métalliques — Essai de dureté Vickers —
Partie 4: Tableaux des valeurs de dureté

Reference number
ISO 6507-4:2005(E)
©
ISO 2005
ISO 6507-4:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 6507-4:2005(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Tables of Vickers hardness values for use in tests made on flat surfaces. 1

ISO 6507-4:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6507-4 was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals, Subcommittee
SC 3, Hardness testing.
This first edition cancels and replaces Annexes B, C and D of ISO 6507-1:1997.
ISO 6507 consists of the following parts, under the general title Metallic materials — Vickers hardness test:
⎯ Part 1: Test method
⎯ Part 2: Verification and calibration of testing machines
⎯ Part 3: Calibration of reference blocks
⎯ Part 4: Tables of hardness values

iv © ISO 2005 – All rights reserved

INTERNATIONAL STANDARD ISO 6507-4:2005(E)

Metallic materials — Vickers hardness test —
Part 4:
Tables of hardness values
1 Scope
This part of ISO 6507 gives tables of Vickers hardness for use in tests made on flat surfaces.
2 Tables of Vickers hardness values for use in tests made on flat surfaces
See Table 1 for range < HV 0,2.
See Table 2 for range HV 0,2 to HV 3.
See Table 3 for range HV 5 to HV 100.
Table 1 — Range < HV 0,2
Test force, F
Mean
N
diagonal
0,009 807 0,019 61 0,049 03 0,098 07 0,196 12 0,245 2 0,490 3 0,980 7
of
indentation
Vickers hardness
d
HV HV HV HV HV HV HV HV
mm
0,001 0,002 0,005 0,01 0,02 0,025 0,05 0,1
0,020 0 4,64 9,27 23,18 46,36 92,72 115,9 231,8 463,6
0,020 2 4,54 9,09 22,72 45,45 90,89 113,6 227,2 454,5
0,020 4 4,46 8,91 22,28 44,56 89,12 111,4 222,8 445,6
0,020 6 4,37 8,74 21,85 43,70 87,39 109,3 218,5 437,0
0,020 8 4,29 8,57 21,43 42,86 85,72 107,2 214,3 428,6
0,021 0 4,21 8,41 21,02 42,05 84,10 105,1 210,2 420,5
0,021 2 4,13 8,25 20,63 41,26 82,52 103,2 206,3 412,6
0,021 4 4,05 8,10 20,25 40,49 80,98 101,2 202,5 404,9
0,021 6 3,97 7,95 19,87 39,75 79,49 99,38 198,7 397,5
0,021 8 3,90 7,80 19,51 39,02 78,04 97,57 195,1 390,2
0,022 0 3,83 7,66 19,16 38,32 76,62 95,80 191,6 383,2
0,022 2 3,76 7,52 18,81 37,63 75,25 94,08 188,1 376,3
0,022 4 3,70 7,39 18,48 36,96 73,91 92,41 184,8 369,6
0,022 6 3,63 7,26 18,15 36,31 72,61 90,78 181,5 363,1
0,022 8 3,57 7,13 17,84 35,67 71,34 89,20 178,4 356,7
0,023 0 3,51 7,01 17,53 35,06 70,11 87,65 175,3 350,6
0,023 2 3,45 6,89 17,23 34,45 68,90 86,15 172,3 344,5
0,023 4 3,39 6,77 16,93 33,87 67,73 84,68 169,3 338,7
0,023 6 3,33 6,66 16,65 33,30 66,59 83,25 166,5 333,0
0,023 8 3,27 6,55 16,37 32,74 65,47 81,86 163,7 327,4

ISO 6507-4:2005(E)
Table 1 (continued)
Test force, F
Mean
N
diagonal
0,009 807 0,019 61 0,049 03 0,098 07 0,196 12 0,245 2 0,490 3 0,980 7
of
indentation
Vickers hardness
d
HV HV HV HV HV HV HV HV
mm
0,001 0,002 0,005 0,01 0,02 0,025 0,05 0,1
0,024 0 3,22 6,44 16,10 32,20 64,39 80,50 161,0 322,0
0,024 2 3,17 6,33 15,83 31,67 63,33 79,17 158,3 316,7
0,024 4 3,11 6,23 15,57 31,15 62,29 77,88 155,7 311,5
0,024 6 3,06 6,13 15,32 30,64 61,28 76,62 153,2 306,4
0,024 8 3,02 6,03 15,07 30,15 60,30 75,39 150,7 301,5
0,025 0 2,97 5,93 14,83 29,67 59,34 74,19 148,3 296,7
0,025 2 2,92 5,84 14,60 29,20 58,40 73,01 146,0 292,0
0,025 4 2,87 5,75 14,37 28,74 57,48 71,87 143,7 287,4
0,025 6 2,83 5,66 14,15 28,30 56,59
70,75 141,5 283,0
0,025 8 2,79 5,57 13,93 27,86 55,72 69,66 139,3 278,6
0,026 0 2,74 5,49 13,72 27,43 54,86 68,59 137,2 274,3
0,026 2 2,70 5,40 13,51 27,02 54,03 67,55 135,1 270,2
0,026 4 2,66 5,32 13,30 26,61 53,21 66,53 133,0 266,1
0,026 6 2,62 5,24 13,10 26,21 52,41 65,53 131,0 262,1
0,026 8 2,58 5,16 12,91 25,82 51,63 64,56 129,1 258,2
0,027 0 2,54 5,09 12,72 25,44 50,87 63,60 127,2 254,4
0,027 2 2,51 5,01 12,53 25,07 50,13 62,67 125,3 250,7
0,027 4 2,47 4,94 12,35 24,70 49,40 61,76 123,5 247,0
0,027 6 2,43 4,87 12,17 24,34 48,69 60,87 121,7 243,4
0,027 8 2,40 4,80 12,00 24,00 47,99 60,00 120,0 240,0
0,028 0 2,37 4,73 11,83 23,65 47,30 59,14 118,3 236,5
0,028 2 2,33 4,66 11,66 23,32 46,64 58,31 116,6 233,2
0,028 4 2,30 4,60 11,50 22,99 45,98 57,49 115,0 229,9
0,028 6 2,27 4,53 11,33 22,67 45,34 56,69 113,3 226,7
0,028 8 2,24 4,47 11,18 22,36 44,71 55,90 111,8 223,6
0,029 0 2,21 4,41 11,02 22,05 44,10 55,13 110,2 220,5
0,029 2 2,18 4,35 10,87 21,75 43,50 54,38 108,7 217,5
0,029 4 2,15 4,29 10,73 21,46 42,91 53,64 107,3 214,6
0,029 6 2,12 4,23 10,58 21,17 42,33 52,92 105,8 211,7
0,029 8 2,09 4,18 10,44 20,88 41,76 52,21 104,4 208,8
0,030 0 2,06 4,12 10,30 20,61 41,21 51,52 103,0 206,1
0,030 2 2,03 4,07 10,17 20,33 40,66 50,84 101,7 203,3
0,030 4 2,01 4,01 10,03 20,07 40,13 50,17 100,3 200,7
0,030 6 1,98 3,96 9,90 19,81 39,61 49,52 99,02 198,1
0,030 8 1,95 3,91 9,77 19,55 39,09 48,88 97,74 195,5
0,031 0 1,93 3,86 9,65 19,30 38,59 48,25 96,48 193,0
0,031 2 1,91 3,81 9,52 19,05 38,10 47,63 95,25 190,5
0,031 4 1,88 3,76 9,40 18,81 37,61 47,03 94,04 188,1
0,031 6 1,86 3,71 9,28 18,57 37,14 46,43 92,85 185,7
0,031 8 1,83 3,67 9,17 18,34 36,67 45,85 91,69 183,4
0,032 0 1,81 3,62 9,05 18,11 36,22 45,28 90,54 181,1
0,032 2 1,79 3,58 8,94 17,89 35,77 44,72 89,42 178,9
0,032 4 1,77 3,53 8,83 17,67 35,33 44,17 88,32 176,7
0,032 6 1,74 3,49 8,72 17,45 34,90 43,63 87,24 174,5
0,032 8 1,72 3,45 8,62 17,24 34,47 43,10 86,18 172,4
0,033 0 1,70 3,41 8,51 17,03 34,06 42,58 85,14 170,3
0,033 2 1,68 3,36 8,41 16,82 33,65 42,07 84,12 168,2
0,033 4 1,66 3,32 8,31 16,62 33,24 41,56 83,11 166,2
0,033 6 1,64 3,28 8,21 16,43 32,85 41,07 82,12 164,3
0,033 8 1,62 3,25 8,12 16,23 32,46 40,59 81,16 162,3
2 © ISO 2005 – All rights reserved

ISO 6507-4:2005(E)
Table 1 (continued)
Test force, F
Mean
N
diagonal
0,009 807 0,019 61 0,049 03 0,098 07 0,196 12 0,245 2 0,490 3 0,980 7
of
indentation
Vickers hardness
d
HV HV HV HV HV HV HV HV
mm
0,001 0,002 0,005 0,01 0,02 0,025 0,05 0,1
0,034 0 1,60 3,21 8,02 16,04 32,08 40,11 80,20 160,4
0,034 2 1,59 3,17 7,93 15,86 31,71 39,64 79,27 158,6
0,034 4 1,57 3,13 7,83 15,67 31,34 39,18 78,35 156,7
0,034 6 1,55 3,10 7,74 15,49 30,98 38,73 77,45 154,9
0,034 8 1,53 3,06 7,66 15,31 30,62 38,29 76,56 153,1
0,035 0 1,51 3,03 7,57 15,14 30,27 37,85 75,69 151,4
0,035 2 1,50 2,99 7,48 14,97 29,93 37,42 74,83 149,7
0,035 4 1,48 2,96 7,40 14,80 29,59 37,00 73,99 148,0
0,035 6 1,46 2,93 7,32 14,63 29,26
36,59 73,16 146,3
0,035 8 1,45 2,89 7,23 14,47 28,94 36,18 72,34 144,7
0,036 0 1,43 2,86 7,15 14,31 28,62 35,78 71,54 143,1
0,036 2 1,42 2,83 7,08 14,15 28,30 35,38 70,75 141,5
0,036 4 1,40 2,80 7,00 14,00 27,99 35,00 69,98 140,0
0,036 6 1,38 2,77 6,92 13,84 27,69 34,61 69,21 138,4
0,036 8 1,37 2,74 6,85 13,69 27,39 34,24 68,46 136,9
0,037 0 1,35 2,71 6,77 13,55 27,09 33,87 67,73 135,5
0,037 2 1,34 2,68 6,70 13,40 26,80 33,51 67,00 134,0
0,037 4 1,33 2,65 6,63 13,26 26,51 33,15 66,28 132,6
0,037 6 1,31 2,62 6,56 13,12 26,23 32,80 65,58 131,2
0,037 8 1,30 2,60 6,49 12,98 25,96 32,45 64,89 129,8
0,038 0 1,28 2,57 6,42 12,84 25,68 32,11 64,21 128,4
0,038 2 1,27 2,54 6,35 12,71 25,41 31,77 63,54 127,1
0,038 4 1,26 2,51 6,29 12,58 25,15 31,44 62,88 125,8
0,038 6 1,24 2,49 6,22 12,45 24,89 31,12 62,23 124,5
0,038 8 1,23 2,46 6,16 12,32 24,63 30,80 61,59 123,2
0,039 0 1,22 2,44 6,10 12,19 24,38 30,48 60,96 121,9
0,039 2 1,21 2,41 6,03 12,07 24,13 30,17 60,34 120,7
0,039 4 1,19 2,39 5,97 11,95 23,89 29,87 59,73 119,5
0,039 6 1,18 2,36 5,91 11,83 23,65 29,57 59,12 118,3
0,039 8 1,17 2,34 5,85 11,71 23,41 29,27 58,53 117,1
0,040 0 1,16 2,
...