prEN 1993-5
(Main)Eurocode 3 - Design of steel structures - Part 5: Piling
Eurocode 3 - Design of steel structures - Part 5: Piling
(1) EN 1993-5 provides rules for structural design of bearing piles and sheet piles made of steel.
(2) EN 1993-5 provides rules for the structural design of steel elements for foundations and retaining wall structures constructed using steel piles.
(3) EN 1993-5 is applicable to:
— steel piled foundations for civil engineering works on land and over water;
— temporary or permanent structures needed to carry out steel piling work;
— temporary and permanent retaining structures made of continuous steel piling.
(4) EN1993-5 does not apply to:
— offshore platforms;
— dolphins;
— ground reinforcing elements.
NOTE : Ground reinforcing elements include rock bolts; soil nails; sprayed concrete; wire mesh and facing elements.
(5) EN 1993-5 does not cover the following aspects :
— geotechnical design;
— seismic design.
NOTE 1 For geotechnical design refer to EN 1997 (all parts).
NOTE 2 For the effects of ground movement caused by earthquakes refer to EN 1998-5.
(6) EN 1993-5 provides methods for design by calculation and for design assisted by testing.
Eurocode 3 - Bemessung und Konstruktion von Stahlbauten - Teil 5: Pfähle und Spundwände
Eurocode 3 - Calcul des structures en acier - Partie 5: Pieux et palplanches
Evrokod 3 - Projektiranje jeklenih konstrukcij - 5. del: Pilotiranje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2023
Nadomešča:
SIST EN 1993-5:2007
Evrokod 3 - Projektiranje jeklenih konstrukcij - 5. del: Pilotiranje
Eurocode 3 - Design of steel structures - Part 5: Piling
Eurocode 3 - Bemessung und Konstruktion von Stahlbauten - Teil 5: Pfähle und
Spundwände
Eurocode 3 - Calcul des structures en acier - Partie 5: Pieux et palplanches
Ta slovenski standard je istoveten z: prEN 1993-5
ICS:
91.010.30 Tehnični vidiki Technical aspects
91.080.13 Jeklene konstrukcije Steel structures
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2023
ICS Will supersede EN 1993-5:2007
English Version
Eurocode 3 - Design of steel structures - Part 5: Piling
Eurocode 3 - Calcul des structures en acier - Partie 5: Eurocode 3 - Bemessung und Konstruktion von
Pieux et palplanches Stahlbauten - Teil 5: Pfähle und Spundwände
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 250.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1993-5:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 7
0 Introduction . 8
1 Scope .11
1.1 Scope of EN 1993-5 .11
1.2 Assumptions .11
2 Normative references .12
3 Terms, definitions, symbols .13
3.1 Terms and definitions .13
3.1.1 Terms and definitions for piles .13
3.1.2 Terms and definitions relating to anchors, tension piles and waling .16
3.2 Symbols .22
3.2.1 General .22
3.2.2 Latin upper-case symbols .23
3.2.3 Latin lower-case symbols .25
3.2.4 Greek symbols .26
3.3 Convention for sheet pile axes .28
4 Basis of design .29
4.1.1 Basic requirements .29
4.1.2 Structural reliability and consequences of failure .30
4.1.3 Robustness.30
4.1.4 Design service life .31
4.1.5 Durability .31
4.1.6 Sustainability .31
4.2 Principles of limit state design .31
4.2.1 Design situations .31
4.2.2 Ultimate limit state criteria .31
4.2.3 Serviceability limit state criteria .32
4.3 Basic variables .33
4.3.1 Actions and environmental influences .33
4.3.2 Material and product properties and geometrical data.34
4.4 Verification by the partial factor method .34
4.4.1 Design values of actions .34
4.4.2 Design values of material properties .34
4.4.3 Design values of geometrical properties .34
4.4.4 Construction tolerances .34
4.4.5 Imperfections .34
4.5 Driveability .34
4.6 Design assisted by finite element analysis.35
4.6.1 General .35
4.6.2 Secondary elements .35
4.7 Design assisted by testing .35
4.8 Verification by observational method .36
4.9 Fatigue .36
5 Materials .36
5.1 General .36
5.2 Material properties for steel piles .36
5.2.1 Strength of bearing piles .36
5.2.2 Strength of hot rolled sheet piles .37
5.2.3 Strength of cold formed sheet piles . 37
5.2.4 Strength of steel members used for combined walls . 37
5.2.5 Ductility of steel piles . 38
5.2.6 Fracture toughness of steel piles . 38
5.3 Interlocks and connecting devices . 39
5.4 Material properties for steel elements used for anchors and tension piles . 39
5.4.1 General . 39
5.4.2 Anchor tension elements . 39
5.4.3 Ductility of anchors and tension piles . 40
5.5 Material properties for steel members used for bracing . 40
6 Durability . 40
6.1 General . 40
6.2 Durability requirements for piling . 42
6.3 Durability requirements for anchors and tension piles . 43
6.4 Corrosion rates for design . 43
6.4.1 Corrosion rates for design in soil and water . 43
6.4.2 Corrosion rates for design due to mechanical wearing . 45
6.4.3 Corrosion due to stray currents . 46
6.4.4 Corrosion rates for design in atmospheric environment . 46
7 Structural analysis . 46
7.1 Structural modelling . 46
7.1.1 Modelling of the structure . 46
7.1.2 Modelling of anchors, tension piles, walings, bracing and connections . 46
7.2 Global analysis for ultimate limit state design checks . 47
7.3 Imperfections . 51
7.4 Methods of analysis considering material nonlinearities . 52
7.5 Classification of cross-sections . 52
7.5.1 Classification of U, Z and Ω sheet piles . 52
7.5.2 Classification of other cross-sections . 53
8 Ultimate limit state . 53
8.1 General . 53
8.2 Partial factors . 54
8.3 Sheet piling .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.