EN ISO 4033:2000
(Main)Hexagon nuts, style 2 - Product grades A and B (ISO 4033:1999)
Hexagon nuts, style 2 - Product grades A and B (ISO 4033:1999)
Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months because //FV has been missed (Res BT C 243/1999) (CC/991125)
Sechskantmuttern, Typ 2 - Produktklassen A und B (ISO 4033:1999)
Diese Internationale Norm enthält Festlegungen über Sechskantmuttern, Typ 2, mit Gewinden von M5 bis M36, in Produktklasse A für Gewinde d <= M16 und Produktklasse B für Gewinde d > M16. Falls in besonderen Fällen andere Festlegungen als die in dieser Norm aufgeführten benötigt werden, sollten diese den entsprechenden Internationalen Normen entnommen werden, z.B. ISO 724, ISO 898-2, ISO 965-1 und ISO 4759-1. ANMERKUNG: Sechskantmuttern Typ 1 siehe ISO 4032.
Ecrous hexagonaux, style 2 - Grades A et B (ISO 4033:1999)
Šestrobe matice, tip 2 - Razreda izdelave A in B (ISO 4033:1999)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4033:2002
01-julij-2002
1DGRPHãþD
SIST EN 24033:1996
Šestrobe matice, tip 2 - Razreda izdelave A in B (ISO 4033:1999)
Hexagon nuts, style 2 - Product grades A and B (ISO 4033:1999)
Sechskantmuttern, Typ 2 - Produktklassen A und B (ISO 4033:1999)
Ecrous hexagonaux, style 2 - Grades A et B (ISO 4033:1999)
Ta slovenski standard je istoveten z: EN ISO 4033:2000
ICS:
21.060.20 Matice Nuts
SIST EN ISO 4033:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 4033:2002
---------------------- Page: 2 ----------------------
SIST EN ISO 4033:2002
---------------------- Page: 3 ----------------------
SIST EN ISO 4033:2002
---------------------- Page: 4 ----------------------
SIST EN ISO 4033:2002
---------------------- Page: 5 ----------------------
SIST EN ISO 4033:2002
---------------------- Page: 6 ----------------------
SIST EN ISO 4033:2002
INTERNATIONAL ISO
STANDARD 4033
Second edition
1999-08-15
Hexagon nuts, style 2 — Product
grades A and B
Écrous hexagonaux, style 2 — Grades A et B
A
Reference number
ISO 4033:1999(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 4033:2002
ISO 4033:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 4033 was prepared by Technical Committee ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 4033:1979) which has been technically revised.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
---------------------- Page: 8 ----------------------
SIST EN ISO 4033:2002
© ISO
ISO 4033:1999(E)
Introduction
This International Standard is part of the complete ISO product standard series on external hexagon drive
fasteners. The series comprises:
a) hexagon head bolts (ISO 4014 to ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032 to ISO 4036, ISO 8673 to ISO 8675);
d) hexagon bolts with flange (ISO 4162 and ISO 15071);
e) hexagon nuts with flange (ISO 4161 and ISO 10663);
f) structural bolts and nuts (ISO 4775, ISO 7411 to ISO 7414 and ISO 7417).
iii
---------------------- Page: 9 ----------------------
SIST EN ISO 4033:2002
---------------------- Page: 10 ----------------------
SIST EN ISO 4033:2002
INTERNATIONAL STANDARD © ISO ISO 4033:1999(E)
Hexagon nuts, style 2 — Product grades A and B
1 Scope
This International Standard specifies the characteristics of hexagon nuts, style 2, with threads from M5 up to and
including M36, with product grade A for threads d < d .
M16 and product grade B for threads M16.
If, in special cases, specifications other than those listed in this International Standard are required, they should be
selected from existing International Standards, for example ISO 724, ISO 898-2, ISO 965-1 and ISO 4759-1.
NOTE For hexagon nuts style 1, see ISO 4032.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.