EN ISO 2811-3:2023
(Main)Paints and varnishes - Determination of density - Part 3: Oscillation method (ISO 2811-3:2023)
Paints and varnishes - Determination of density - Part 3: Oscillation method (ISO 2811-3:2023)
ISO 2811-3:2011 specifies a method for determining the density of paints, varnishes and related products using an oscillator.
The method is suitable for all materials, including paste-like coatings. If a pressure-resistant type of apparatus is used, the method is also applicable to aerosols.
Beschichtungsstoffe - Bestimmung der Dichte - Teil 3: Schwingungsverfahren (ISO 2811-3:2023)
Dieses Dokument legt ein Verfahren zum Bestimmen der Dichte von Beschichtungsstoffen und ähnlichen Produkten mit einem Schwingungs-Dichtemesser fest.
Das Verfahren ist für alle Beschichtungsstoffe einschließlich pastenförmiger anwendbar. Wenn eine druckfeste Ausführung des Gerätes verwendet wird, ist das Verfahren auch für Aerosole anwendbar.
Peintures et vernis - Détermination de la masse volumique - Partie 3: Méthode par oscillation (ISO 2811-3:2023)
L'ISO 2811-3:2011 spécifie une méthode de détermination de la masse volumique des peintures, vernis et produits assimilés au moyen d'un oscillateur.
La méthode convient pour tous les produits, y compris les revêtements de consistance pâteuse. Si un type d'appareillage résistant à la pression est utilisé, la méthode est également applicable aux aérosols.
Barve in laki - Določanje gostote - 3. del: Oscilacijska metoda (ISO 2811-3:2023)
Standard ISO 2811-3:2011 določa metodo za določanje gostote barv, lakov in sorodnih izdelkov z uporabo oscilatorja.
Metoda je ustrezna za vse materiale, vključno s premazi, podobnimi pasti. V primeru uporabe tlačno odpornega aparata se metoda uporablja tudi za aerosole.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2024
Nadomešča:
SIST EN ISO 2811-3:2011
Barve in laki - Določanje gostote - 3. del: Oscilacijska metoda (ISO 2811-3:2023)
Paints and varnishes - Determination of density - Part 3: Oscillation method (ISO 2811-
3:2023)
Beschichtungsstoffe - Bestimmung der Dichte - Teil 3: Schwingungsverfahren (ISO 2811
-3:2023)
Peintures et vernis - Détermination de la masse volumique - Partie 3: Méthode par
oscillation (ISO 2811-3:2023)
Ta slovenski standard je istoveten z: EN ISO 2811-3:2023
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 2811-3
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2023
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 2811-3:2011
English Version
Paints and varnishes - Determination of density - Part 3:
Oscillation method (ISO 2811-3:2023)
Peintures et vernis - Détermination de la masse Beschichtungsstoffe - Bestimmung der Dichte - Teil 3:
volumique - Partie 3: Méthode par oscillation (ISO Schwingungsverfahren (ISO 2811-3:2023)
2811-3:2023)
This European Standard was approved by CEN on 2 July 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2811-3:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 2811-3:2023) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2024, and conflicting national standards shall be
withdrawn at the latest by May 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2811-3:2011.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 2811-3:2023 has been approved by CEN as EN ISO 2811-3:2023 without any
modification.
INTERNATIONAL ISO
STANDARD 2811-3
Third edition
2023-10
Paints and varnishes — Determination
of density —
Part 3:
Oscillation method
Peintures et vernis — Détermination de la masse volumique —
Partie 3: Méthode par oscillation
Reference number
ISO 2811-3:2023(E)
ISO 2811-3:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 2811-3:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Temperature . 1
6 Apparatus . 2
7 Sampling . 2
8 Procedure .2
8.1 General . 2
8.2 Determination . 2
9 Calculation . 3
10 Precision . 3
10.1 General . 3
10.2 Repeatability limit, r . . 3
10.3 Reproducibility limit, R . 3
11 Test report . 3
Annex A (informative) Calibration of the apparatus — Determination of the apparatus
constants . 5
Annex B (informative) Density values for damp air and air-free water .6
Annex C (informative) Calculation of density at the reference temperature from
measurements at other temperatures . 8
Bibliography . 9
iii
ISO 2811-3:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 2811-3:2011), which has been technically
revised.
The main changes are as follows:
— a requirement has been added to 8.2, to de-aerate the sample prior to the determination in order to
achieve reproducible results for the density;
— Table B.3 has been deleted;
— a bibliography has been added.
A list of all parts in the ISO 2811 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 2811-3:2023(E)
Paints and varnishes — Determination of density —
Part 3:
Oscillation method
1 Scope
This document specifies a method for determining the density of paints, varnishes and related products
using an oscillator.
The method is suitable for all materials, including paste-like coatings. If a pressure-resistant type of
apparatus is used, the method is also applicable to aerosols.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1513, Paints
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.