Abstract

This document specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:
Method A, using a trouser test piece;
Method B, using an angle test piece without a nick.

Status
Published
Publication Date
27-Oct-2026
Technical Committee
CEN/TC 249 - Plastics
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
28-Oct-2026
Completion Date
28-Oct-2026

Buy Documents

EN ISO 8067:2026 is a CEN standard for determining the tear strength of flexible cellular polymeric materials. It specifies two laboratory methods: Method A with a trouser test piece and Method B with an angle test piece without a nick. The document is written for testing flexible foam materials where tear resistance has to be measured in a repeatable way.

What does EN ISO 8067:2026 specify?

EN ISO 8067:2026 specifies the scope of the tear-strength test and the full test workflow, from apparatus and test-piece preparation to calculation and reporting. It is organized into clauses on apparatus, test pieces, number of test pieces, conditioning, procedure, expression of results, and test report, plus one informative annex on precision.

AnnexWhat it covers
Annex APrecision comparison for the two types of test piece

The document covers two tear methods for flexible cellular polymeric materials only. Clause 1 names Method A and Method B, and the rest of the document explains how to prepare, test, calculate, and report the result for each method.

What are the key requirements of EN ISO 8067:2026?

EN ISO 8067:2026 requires a tensile-testing machine that shows the force at rupture, with accuracy class 2 or better to ISO 7500-1. In practice, the machine must be able to capture the maximum force cleanly, because that value is used directly in the tear-strength result.

Test pieces and orientation

Clause 5 requires test pieces free of voids and flow lines. They may be taken with or without skin, but if the material has a predominant direction of cellular structure, the test piece has to be oriented relative to the predominant foam-rise direction, and any unavoidable orientation must be stated in the test report.

Method A uses a trouser test piece cut from sheet material, with a 45 mm to 55 mm cut at one end and a marked tear length of 25 mm. Method B uses an angle test piece cut from a sheet with thickness between 10 mm and 15 mm. These shapes matter because they control how the tear starts and propagates.

Number of test pieces

Clause 6 requires three test pieces. Additional test pieces are used if the spread of results is too large or if the tear path deviates during Method A. This keeps the reported value representative of the material rather than a single abnormal tear.

Conditioning before test

Clause 7 sets the conditioning rules. Materials are normally not tested before 72 h after manufacture, unless earlier results are shown to stay within ±10 % of the 72 h mean. Test pieces are then conditioned for at least 16 h in one of two specified atmospheres, and quality-control testing may use shorter manufacture and conditioning times within stated limits.

Procedure and result calculation

Clause 8 requires thickness measurement in accordance with ISO 1923 before the tear test. For Method A, the jaw speed is 50 mm/min to 500 mm/min, and the tear is followed until 25 ± 5 mm has been torn; rupture before 20 mm means the piece is rejected. For referee purposes, Method A uses 50 ± 5 mm/min. For Method B, the specimen is clamped symmetrically, the same speed range applies, and the referee speed is 500 ± 50 mm/min.

Clause 9 defines tear strength R as the maximum force divided by the original thickness, reported in newtons per centimetre (N/cm). The result is the median of the three values, and if one or more values differs by more than 20 % from that median, two more test pieces are tested and the median of all five values is reported.

Reporting

Clause 10 requires the report to identify the document, the material, the test-piece type, conditioning, jaw speed, sampling location, predominant cellular direction if relevant, skin surfaces if any, original thickness, median tear strength, deviations, and the test date. This makes the result traceable for quality control, product comparison, and dispute work.

What terms does EN ISO 8067:2026 define?

  • Tear strength R - The maximum force per unit thickness observed when a test piece is stretched to rupture.
  • Method A - The tear test using a trouser test piece.
  • Method B - The tear test using an angle test piece without a nick.
  • Trouser test piece - The specimen shape used for Method A, with a pre-cut end that starts the tear.
  • Angle test piece - The specimen shape used for Method B, cut from a sheet with a V-shaped side.
  • Predominant foam-rise direction - The main direction of the cellular structure, used to orient the specimen.
  • Conditioning - The required storage atmosphere and time before testing.
  • Referee purposes - The stricter test conditions used when a formal or disputed result is needed.

Who uses EN ISO 8067:2026?

EN ISO 8067:2026 is used by laboratories that test flexible cellular polymeric materials, by manufacturers of foam products, and by quality-control teams that need comparable tear-strength results. It is also useful for buyers and technical reviewers who need to compare materials using the same test method and reporting format.

What changed in EN ISO 8067:2026 from the previous edition?

The foreword says this edition cancels and replaces ISO 8067:2018 and that it has been technically revised. The main change stated in the document is in Clause 10 f), where the location and number of surfaces with skin were added.

Which standards are used with EN ISO 8067:2026?

  • ISO 1923 - Used to measure the thickness of the test piece before calculating tear strength.
  • ISO 7500-1 - Sets the machine calibration and verification level for the tensile-testing machine force system.
  • ISO/TR 9272 - Used in Annex A to calculate the precision data for the comparative trial.

What does the EN ISO 8067:2026 document contain?

The document contains the two test methods, specimen shapes, conditioning requirements, test speeds, result formula, and reporting items needed to measure tear strength. It also includes figures for the trouser and angle test pieces and the test arrangement for Method A, plus a worked precision comparison in Annex A. Annex A compares the two specimen types using flexible polyurethane foam and presents precision data that support method selection and laboratory assessment.

Relations

Effective Date
13-Mar-2024
Effective Date
12-Feb-2026

Buy Documents

Get Certified

Connect with accredited certification bodies for this standard

DIN CERTCO

DIN Group product certification.

DAKKS Germany Verified

Smithers Quality Assessments

US management systems and product certification.

ANAB United States Verified

Sponsored listings

Frequently Asked Questions

EN ISO 8067:2026 is a standard published by the European Committee for Standardization (CEN). Its full title is "Flexible cellular polymeric materials - Determination of tear strength (ISO 8067:2026)". This standard covers: This document specifies two methods for the determination of the tear strength of flexible cellular polymeric materials: Method A, using a trouser test piece; Method B, using an angle test piece without a nick.

This document specifies two methods for the determination of the tear strength of flexible cellular polymeric materials: Method A, using a trouser test piece; Method B, using an angle test piece without a nick.

EN ISO 8067:2026 is classified under the following ICS (International Classification for Standards) categories: 83.100 - Cellular materials. The ICS classification helps identify the subject area and facilitates finding related standards.

EN ISO 8067:2026 has the following relationships with other standards: It is inter standard links to EN ISO 8067:2018, ISO 8067:2026. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN ISO 8067:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2027
Mehki penjeni polimerni materiali - Ugotavljanje pretržne trdnosti (ISO 8067:2026)
Flexible cellular polymeric materials - Determination of tear strength (ISO 8067:2026)
Flexible Polymer-Schaumstoffe - Bestimmung des Weiterreißwiderstands (ISO
8067:2026)
Matériaux polymères alvéolaires souples - Détermination de la résistance au
déchirement (ISO 8067:2026)
Ta slovenski standard je istoveten z: EN ISO 8067:2026
ICS:
83.100 Penjeni polimeri Cellular materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 8067
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2026
EUROPÄISCHE NORM
ICS 83.100 Supersedes EN ISO 8067:2018
English Version
Flexible cellular polymeric materials - Determination of
tear strength (ISO 8067:2026)
Matériaux polymères alvéolaires souples - Flexible Polymer-Schaumstoffe - Bestimmung des
Détermination de la résistance au déchirement (ISO Weiterreißwiderstands (ISO 8067:2026)
8067:2026)
This European Standard was approved by CEN on 20 September 2025.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8067:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 8067:2026) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of
which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2027, and conflicting national standards shall be
withdrawn at the latest by April 2027.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8067:2018.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8067:2026 has been approved by CEN as EN ISO 8067:2026 without any modification.

International
Standard
ISO 8067
Fourth edition
Flexible cellular polymeric
2026-09
materials — Determination of tear
strength
Matériaux polymères alvéolaires souples — Détermination de la
résistance au déchirement
Reference number
ISO 8067:2026(en) © ISO 2026
ISO 8067:2026(en)
© ISO 2026
All rights reserved.
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
an ISO member body, or an authorized third-party distributor.
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
photocopying, scanning, recording, or posting on internal or external digital platforms.
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 8067:2026(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 1
5 Test pieces . 2
5.1 General .2
5.2 Trouser test piece for method A .2
5.3 Angle test piece for method B .3
6 Number of test pieces . 4
7 Conditioning . 4
8 Procedure . 5
8.1 General .5
8.2 Method A .5
8.3 Method B .6
9 Expression of results . 6
10 Test report . 6
Annex A (informative) Precision comparison for the two types of test piece. 8
Bibliography .10

iii
ISO 8067:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 4, Products (other than hoses), in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 8067:2018), which has been technically
revised.
The main change is as follows:
— addition of information regarding the location and number of surfaces with skin in Clause 10.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

© ISO
...