iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 850:1996

(Main)

Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical use

Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical use

This European Standard applies to pin-index, yoke-type valve outlet connections for medical use, up to a maximum working pressure of 250 bar at 15 °C. These connections are for use with medical gas cylinders of water capacity below 5 l, for patient care, including therapeutic, diagnostic and prophylactic applications, in hospitals and for emergency treatment. It specifies: - basic dimensions; - requirements for alternative designs of pin-index, yoke-type valve connections; - dimension and positions for the holes and pins for the outlet connections for certain gases and gas mixtures.

Ortsbewegliche Gasflaschen - Ventilseitenstutzen mit Anschlußbügel nach dem Pin-index-System für medizinische Anwendung

Diese Europäische Norm gilt für Bügelverschlüsse nach dem Pin-Index System für die medizinische Anwendung, mit einem maximalen Fülldruck von 250 bar bei 15 °C. Diese Verschlüsse gelten für den medizinischen Gebrauch von Gasflaschen  mit weniger als 5 l Inhalt für die Krankenpflege, einschließlich therapeutischer, diagnostischer und prophylaktischer Anwendung, in Krankenhäusern und für Notfälle. Sie bestimmt: - Grundmaße; - Anforderungen für alternative Konstruktionen von Bügelventilverschlüssen; - Maße und Anordnungen der Paßlöcher und -stifte für die Auslaßverbindungen.

Bouteilles à gaz transportables - Raccords de sortie de robinets du type à étrier avec ergots de sécurité pour usage médical

Cette norme européenne s'applique aux raccords de sorties de robinets du type à étrier avec ergots de sécurité pour usage médical jusqu'à une pression de service maximale de 250 bar à 15 °C. Ces raccords de sorties sont utilisés pour les bouteilles à gaz médicaux, de contenance en eau inférieure à 5 l et, utilisés pour des soins aux malades comportant des applications thérapeutiques, diagnostiques et prophylactiques, dans les hôpitaux et pour les traitements d'urgence. Elle prescrit: - leurs dimensions de base.

Plinske jeklenke - Objemni nastavki ventila s sistemom pin-index za uporabo v medicini

General Information

Status
Withdrawn
Publication Date
23-Jul-1996
Withdrawal Date
31-Oct-2004
ICS
23.060.40 - Pressure regulators
Technical Committee
CEN/TC 23 - Transportable gas cylinders
Drafting Committee
CEN/TC 23/SC 2 - Fittings
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Nov-2004
Completion Date
01-Nov-2004
Ref Project
SIST EN 850:1999 - Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical use

Relations

Amended By
EN 850:1996/A1:2000 - Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical use
Effective Date
22-Dec-2008
Replaced By
EN ISO 407:2004 - Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2004)
Effective Date
22-Dec-2008
Corrected By
EN 850:1996/AC:1998 - Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical use
Effective Date
22-Dec-2008

Buy Standard

EN 850:1999EN 850:1999
PreviousNext
Standard
EN 850:1999
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 850:1999
01-januar-1999
Plinske jeklenke - Objemni nastavki ventila s sistemom pin-index za uporabo v
medicini
Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical
use
Ortsbewegliche Gasflaschen - Ventilseitenstutzen mit Anschlußbügel nach dem Pin-
index-System für medizinische Anwendung
Bouteilles a gaz transportables - Raccords de sortie de robinets du type a étrier avec
ergots de sécurité pour usage médical
Ta slovenski standard je istoveten z: EN 850:1996
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
SIST EN 850:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 850:1999

---------------------- Page: 2 ----------------------

SIST EN 850:1999

---------------------- Page: 3 ----------------------

SIST EN 850:1999

---------------------- Page: 4 ----------------------

SIST EN 850:1999

---------------------- Page: 5 ----------------------

SIST EN 850:1999

---------------------- Page: 6 ----------------------

SIST EN 850:1999

---------------------- Page: 7 ----------------------

SIST EN 850:1999

---------------------- Page: 8 ----------------------

SIST EN 850:1999

---------------------- Page: 9 ----------------------

SIST EN 850:1999

---------------------- Page: 10 ----------------------

SIST EN 850:1999

---------------------- Page: 11 ----------------------

SIST EN 850:1999

---------------------- Page:
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 17871:2020(Main)
Gas cylinders - Quick-release cylinder valves - Specification and type testing (ISO 17871:2020)
SIST EN ISO 17871:2020

This document, in conjunction with ISO 10297 and ISO 14246, specifies design, type testing, marking and manufacturing tests, and examinations requirements for quick-release cylinder valves intended to be fitted to refillable transportable gas cylinders, pressure drums and tubes which convey:
—     non-toxic;
—     non-oxidizing;
—     non-flammable; and
—     non-corrosive;
compressed or liquefied gases or extinguishing agents charged with compressed gases to be used for fire-extinguishing, explosion protection, and rescue applications.
NOTE 1  The main application of such quick-release cylinder valves is in the fire-fighting industry. However, there are other applications such as avalanche airbags, life raft inflation and similar applications.
NOTE 2  Where there is no risk of ambiguity, gas cylinders, pressure drums and tubes are addressed with the collective term "cylinders" within this document.
This document covers the function of a quick-release cylinder valve as a closure.
This document does not apply to quick-release cylinder valves for cryogenic equipment and for liquefied petroleum gas (LPG).
This document does not apply to quick-release cylinder valves if used as the main closure of portable fire extinguishers because portable fire extinguishers are not covered by transport regulation.
Quick-release cylinder valves of auxiliary refillable propellant gas cylinders used within or as part of portable fire extinguishers are covered by this document, if these cylinders are transported separately, e.g. for filling (see UN Model Regulations, Chapter 3.3, Special Provision 225, second note[1]).

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17879:2017(Main)
Gas cylinders - Self-closing cylinder valves - Specification and type testing (ISO 17879:2017)
SIST EN ISO 17879:2018

ISO 17879:2017 specifies the design, type testing, marking and manufacturing tests and examinations requirements for self-closing cylinder valves intended to be fitted to refillable transportable gas cylinders which convey compressed, liquefied or dissolved gases.
NOTE 1       The main applications for such self-closing cylinder valves are in the calibration gas and beverage industries.
ISO 17879:2017 covers the function of a self-closing cylinder valve as a closure.
NOTE 2       Requirements for standard cylinder valves are given in ISO 10297. Requirements for quick-release cylinder valves are given in ISO 17871.
ISO 17879:2017 is not applicable to self-closing cylinder valves for cryogenic equipment, for portable fire extinguishers, or for liquefied petroleum gas (LPG).
NOTE 3       Requirements for valves for cryogenic vessels are specified in ISO 21011 and at a regional level, for example, in EN 1626. Requirements for valves for portable fire extinguishers at a regional level are specified, for example, in EN 3 series. Requirements for self-closing LPG cylinder valves are specified in ISO 14245.
NOTE 4       Additional requirements for pressure-relief devices might be specified in international/regional regulations/standards.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15996:2017(Main)
Gas cylinders - Residual pressure valves - Specification and type testing of cylinder valves incorporating residual pressure devices (ISO 15996:2017)
SIST EN ISO 15996:2018

ISO 15996:2017 specifies design, type testing and marking requirements for cylinder valves incorporating residual pressure devices, hereinafter referred to as residual pressure valves (RPVs). This document applies to the following types of RPVs:
a)    cylinder valves intended to be fitted to refillable transportable gas cylinders;
b)    main valves (excluding ball valves) for cylinder bundles;
c)    cylinder valves or main valves with integrated pressure regulator (VIPR);
d)    valves for pressure drums and tubes;
which convey compressed or liquefied gases.
NOTE          Where there is no risk of ambiguity, cylinders, pressure drums, tubes and cylinder bundles are addressed with the collective term "cylinder" within this document.
These requirements are in addition to those in ISO 10297.
For RPD stand-alone devices this document can also be applied.
ISO 15996:2017 does not apply to RPVs for portable fire extinguishers, cryogenic equipment, low pressure refrigerant gases (cylinder test pressure less than 50 bar), dissolved gases or liquefied petroleum gas (LPG).

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11114-4:2017(Main)
Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 4: Test methods for selecting steels resistant to hydrogen embrittlement (ISO 11114-4:2017)
SIST EN ISO 11114-4:2017

ISO 11114-4: 2017 specifies test methods and the evaluation of results from these tests in order to qualify steels suitable for use in the manufacture of gas cylinders (up to 3 000 l) for hydrogen and hydrogen bearing embrittling gases.
This document only applies to seamless steel gas cylinders.
The requirements of this document are not applicable if at least one of the following conditions for the intended gas service is fulfilled:
-      the working pressure of the filled embrittling gas is less than 20 % of the test pressure of the cylinder;
-      the partial pressure of the filled embrittling gas of a gas mixture is less than 5 MPa (50 bar) in the case of hydrogen and other embrittling gases, with the exception of hydrogen sulphide and methyl mercaptan; in such cases, the partial pressure shall not exceed 0,25 MPa (2,5 bar).
NOTE       In such cases, it is possible to design the cylinder as for ordinary (non-embrittling) gases.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10297:2014/A1:2017(Amendment)
Gas cylinders - Cylinder valves - Specification and type testing - Amendment 1: Pressure drums and tubes (ISO 10297:2014/Amd 1:2017)
SIST EN ISO 10297:2014/A1:2018
  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12209:2013/A1:2016(Amendment)
Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Amendment 1: Outlet connection up to a maximum cylinder working pressure of 500 bar (ISO 12209:2013/Amd 1:2016, Corrected version 2017-03)
SIST EN ISO 12209:2013/A1:2017
  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13341:2010/A1:2015(Amendment)
Gas cylinders - Fitting of valves to gas cylinders - Amendment 1 (ISO 13341:2010/Amd 1:2015)
SIST EN ISO 13341:2011/A1:2015

2014-04-17 GVN: Draft for // vote received in ISO/CS (see notification of 2014-04-10 in dataservice).
2013-02-22 EMA: Draft for // ENQ received in ISO/CS (see notification of 2013-02-22 in dataservice).

  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    5 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10297:2014(Main)
Gas cylinders - Cylinder valves - Specification and type testing (ISO 10297:2014, Corrected version 2014-11-01)
SIST EN ISO 10297:2014

ISO 10297:2014 specifies design, type testing and marking requirements for:
a)    cylinder valves intended to be fitted to refillable transportable gas cylinders;
b)    main valves (excluding ball valves) for cylinder bundles;
c)    cylinder valves or main valves with integrated pressure regulator (VIPR);
which convey compressed, liquefied or dissolved gases.
ISO 10297:2014 covers the function of a valve as a closure. It does not apply to valves for cryogenic equipment, portable fire extinguishers and liquefied petroleum gas (LPG) and quick-release valves (e.g. for fire-extinguishing, explosion protection and rescue applications), non-return valves or ball valves.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12209:2013(Main)
Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air (ISO 12209:2013)
SIST EN ISO 12209:2013

ISO 12209:2013 specifies the characteristics of outlet connections for gas cylinder valves for compressed breathable air gas cylinders. It states the fundamental requirements for both; the connection and its components and includes basic dimensions. Included in ISO 12209:2013 the following connections:
a) yoke type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar;
b) threaded type outlet connections up to a maximum cylinder working pressure of 232 bar and 300 bar; and
c) threaded type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar including adaptor for users to convert into a yoke type outlet.
Annex A gives the outlet connection type test procedures.
Requirements for cylinder valves (see ISO 10297) are not covered by ISO 12209:2013.
Requirements for material specifications and gas/material compatibility (see ISO 11114‑1 and ISO 11114‑2) are not covered by ISO 12209:2013.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2007/A1:2012(Amendment)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2007/Amd 1:2012)
SIST EN ISO 22435:2009/A1:2013

2012-06-19 EMA: Draft for // vote received in ISO/CS (see 2012-06-15 notification in dataservice).
2011-02-21 EMA: // ENQ draft received in ISO/CS (see notification from 2011-02-18 in dataservice).

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day