iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 23088:2020

(Main)

Gas cylinders - Periodic inspection and testing of welded steel pressure drums - Capacities up to 1 000 l (ISO 23088:2020)

Gas cylinders - Periodic inspection and testing of welded steel pressure drums - Capacities up to 1 000 l (ISO 23088:2020)

This document specifies the requirements for periodic inspection and testing of welded steel transportable pressure drums of water capacity from 150 l up to 1 000 l and up to 300 bar test pressure intended for compressed and liquefied gases.

Gasflaschen - Wiederkehrende Inspektion und Prüfung von geschweißten Druckfässern aus Stahl - Fassungsräume bis zu 1 000 l (ISO 23088:2020)

Dieses Dokument legt die Anforderungen an die wiederkehrende Inspektion und Prüfung von geschweißten, ortsbeweglichen Druckfässern aus Stahl mit einem Fassungsraum von 150 l bis 1 000 l und einem Prüfdruck von bis zu 300 bar fest, die für verdichtete und verflüssigte Gase vorgesehen sind.
ACHTUNG — Bei einigen der in diesem Dokument festgelegten Prüfungen werden Prozesse angewendet, die zu gefährlichen Situationen führen könnten.

Bouteilles à gaz - Contrôles et essais périodiques des fûts à pression soudés en acier - Capacité inférieure ou égale à 1 000 l (ISO 23088:2020)

Le présent document spécifie les exigences relatives aux contrôles et essais périodiques des fûts à pression soudés en acier transportables d'une capacité de 150 l à 1 000 l et pour une pression d'épreuve maximale de 300 bar, destinés au transport des gaz comprimés et liquéfiés.

Plinske jeklenke - Periodični pregledi in preskušanje varjenih tlačnih sodov - Prostornina do 1000 l (ISO 23088:2020)

General Information

Status
Published
Publication Date
22-Dec-2020
Withdrawal Date
29-Jun-2021
ICS
23.020.35 - Gas cylinders
Technical Committee
CEN/TC 23 - Transportable gas cylinders
Drafting Committee
CEN/TC 23 - Transportable gas cylinders
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
23-Dec-2020
Due Date
02-Aug-2022
Completion Date
23-Dec-2020
Ref Project
SIST EN ISO 23088:2021 - Gas cylinders - Periodic inspection and testing of welded steel pressure drums - Capacities up to 1 000 l (ISO 23088:2020)

Relations

Replaces
EN 14876:2007 - Transportable gas cylinders - Periodic inspection and testing of welded steel pressure drums
Effective Date
07-Apr-2021

Buy Standard

EN ISO 23088:2021 - BARVEEN ISO 23088:2021 - BARVE
PreviousNext
Standard
EN ISO 23088:2021 - BARVE
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 23088:2021
01-februar-2021
Plinske jeklenke - Periodični pregledi in preskušanje varjenih tlačnih sodov -
Prostornina do 1000 l (ISO 23088:2020)
Gas cylinders - Periodic inspection and testing of welded steel pressure drums -
Capacities up to 1 000 l (ISO 23088:2020)
Gasflaschen - Wiederkehrende Inspektion und Prüfung von geschweißten Druckfässern
aus Stahl - Fassungsräume bis zu 1 000 l (ISO 23088:2020)
Bouteilles à gaz - Contrôles et essais périodiques des fûts à pression soudés en acier -
Capacité inférieure ou égale à 1 000 l (ISO 23088:2020)l
Ta slovenski standard je istoveten z: EN ISO 23088:2020
ICS:
23.020.35 Plinske jeklenke Gas cylinders
SIST EN ISO 23088:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 23088:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 23088:2021


EN ISO 23088
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2020
EUROPÄISCHE NORM
ICS 23.020.35
English Version

Gas cylinders - Periodic inspection and testing of welded
steel pressure drums - Capacities up to 1 000 l (ISO
23088:2020)
 Gasflaschen - Wiederkehrende Inspektion und Prüfung
von geschweißten Druckfässern aus Stahl -
Fassungsräume bis zu 1 000 l (ISO 23088:2020)
This European Standard was approved by CEN on 13 December 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23088:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 23088:2021
EN ISO 23088:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 23088:2021
EN ISO 23088:2020 (E)
European foreword
The text of ISO 23088:2020 has been prepared by Technical Committee ISO/TC 58 "Gas cylinders” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 23088:2020
by Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat of which is held by
BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2021, and conflicting national standards shall be
withdrawn at the latest by June 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 23088:2020 has been approved by CEN as EN ISO 23088:2020 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 23088:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 23088:2021
INTERNATIONAL ISO
STANDARD 23088
First edition
2020-02
Gas cylinders — Periodic inspection
and testing of welded steel pressure
drums — Capacities up to
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11623:2023(Main)
Gas cylinders - Composite cylinders and tubes - Periodic inspection and testing (ISO 11623:2023)
SIST EN ISO 11623:2023

This document specifies the requirements for periodic inspection and testing to verify the integrity for further service of hoop-wrapped and fully-wrapped composite transportable gas cylinders and tubes, with aluminium-alloy, steel or non-metallic liners or of linerless construction (Types 2, 3, 4, and 5), intended for compressed, liquefied or dissolved gases under pressure, of water capacity from 0,5 l up to 3 000 l.
This document addresses the periodic inspection and testing of composite cylinders and tubes constructed according to ISO 11119-1, ISO 11119-2, ISO 11119-3, ISO 11119-4 or ISO 11515. It can be applied to other composite cylinders and tubes designed to comparable standards when authorized by the competent authority. As far as practicable, this document can also be applied to cylinders of less than 0,5 l water capacity when authorized by the manufacturer.
NOTE    Unless noted by exception, the use of the word “cylinder” in this document refers to both cylinders and tubes.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11114-1:2020/A1:2023(Amendment)
Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 1: Metallic materials - Amendment 1 (ISO 11114-1:2020/Amd 1:2023)
SIST EN ISO 11114-1:2020/A1:2023
  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11363-1:2018/A1:2023(Amendment)
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Amendment 1 (ISO 11363-1:2018/Amd 1:2023)
SIST EN ISO 11363-1:2018/A1:2023
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9809-4:2022(Main)
Gas cylinders - Design, construction and testing of refillable seamless steel gas cylinders and tubes - Part 4: Stainless steel cylinders with an Rm value of less than 1 100 MPa (ISO 9809-4:2021)
SIST EN ISO 9809-4:2023

This document specifies the minimum requirements for the materials, design, construction and workmanship, manufacturing processes, examinations and testing at time of manufacture for refillable, seamless, stainless steel gas cylinders with water capacities up to and including 150 l.
It is applicable to cylinders for compressed, liquefied and dissolved gases with a maximum actual tensile strength, Rma, of less than 1 100 MPa.
NOTE         If so desired, cylinders of water capacity between 150 l and 450 l can be manufactured to be in full conformance to this document.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10298:2020/A1:2022(Amendment)
Gas cylinders - Gases and gas mixtures - Determination of toxicity for the selection of cylinder valve outlets - Amendment 1 (ISO 10298:2018/Amd 1:2021)
SIST EN ISO 10298:2020/A1:2022

This document lists the best available acute-toxicity data of gases taken from a search of the current literature to allow the classification of gases and gas mixtures for toxicity by inhalation.
Scope of amendment
Changes to formula in clause 4.3

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11114-6:2022(Main)
Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 6: Oxygen pressure surge testing (ISO 11114-6:2022)
SIST EN ISO 11114-6:2022

This document specifies requirements for the test apparatus and test procedure in order to apply oxygen pressure surges consistently to devices being tested for resistance to ignition by adiabatic compression and to materials for oxygen compatibility.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13338:2022(Main)
Gas cylinders - Gases and gas mixtures - Determination of corrosiveness for the selection of cylinder valve outlet (ISO 13338:2022)
SIST EN ISO 13338:2022

This document specifies the following, in order to determine the corrosiveness of gases and gas mixtures so that a suitable outlet connection can be assigned to each of them:
—    for pure gases and some liquids, a complete list indicating their corrosiveness;
—    for gas mixtures, a calculation method, in the absence of experimental data, relating to the corrosiveness of each of their components.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12245:2022(Main)
Transportable gas cylinders - Fully wrapped composite cylinders
SIST EN 12245:2022

This document specifies minimum requirements for the materials, design, construction, prototype testing and routine manufacturing inspections of fully wrapped composite gas cylinders for compressed, liquefied and dissolved gases.
NOTE 1   For the purposes of this document, the word “cylinder” includes tubes (seamless transportable pressure receptacles of a water capacity exceeding 150 l and of not more than 3 000 l).
This document is applicable to cylinders that comprise a liner of metallic material (welded or seamless) or non-metallic material (or a mixture thereof), reinforced by a wound composite consisting of fibres of glass, carbon or aramid (or a mixture thereof) embedded in a matrix.
This document is also applicable to composite cylinders without liners.
This document is not applicable to gas cylinders which are partially covered with fibres and commonly called “hoop wrapped” cylinders. For hoop wrapped composite cylinders, see EN 12257.
NOTE 2   This document does not address the design, fitting and performance of removable protective sleeves. Where these are fitted, they are considered separately.
This document is primarily for compressed, liquefied and dissolved gases other than LPG.
NOTE 3   For dedicated LPG cylinders, see EN 14427.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22434:2022(Main)
Gas cylinders - Inspection and maintenance of valves (ISO 22434:2022)
SIST EN ISO 22434:2022

This document specifies requirements for the inspection and maintenance of valves [including ball valves and valves with integrated pressure regulator (VIPRs)] for:
a) refillable transportable gas cylinders;
b) cylinder bundles;
c) pressure drums and tubes;
which convey compressed, liquefied or dissolved gases.
This document does not apply to valves for liquefied petroleum gas (LPG).
NOTE       Where there is no risk of ambiguity, gas cylinders, cylinder bundles, pressure drums and tubes are addressed with the collective term “gas cylinders” within this document.
This document is applicable to valves reused at the time of the periodic inspection of gas cylinders, cylinder bundles, pressure drums and tubes, and can be applied at any other time, e.g. at a change of gas service (see ISO 11621).
This document does not apply to the routine inspection of valves, e.g. carried out at the time of a gas cylinder filling.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day