EN ISO 22476-6:2018

Geotechnical investigation and testing - Field testing - Part 6: Self boring pressuremeter test (ISO 22476-6:2018)

This document specifies the equipment requirements, execution of and reporting on self-boring pressuremeter (SBP) tests.
NOTE       This document fulfils the requirements for self-boring pressuremeter test as part of the geotechnical investigation services according to EN 1997-1 and EN 1997-2.
Tests with the self-boring pressuremeter cover the measurement in situ of the deformation of soils and weak rocks by the expansion and contraction of a cylindrical flexible membrane under pressure.

Geotechnische Erkundung und Untersuchung - Felduntersuchungen - Teil 6: Versuch mit selbstbohrendem Pressiometer (ISO 22476-6:2018)

Reconnaissance et essais géotechniques - Essais en place - Partie 6: Essai pressiométrique autoforé (ISO 22476-6:2018)

Le présent document spécifie les exigences relatives à l'appareillage, à l'exécution et au compte rendu des essais pressiométriques autoforés (PAF).
NOTE       Ce document satisfait aux exigences relatives aux essais pressiométriques autoforés dans le cadre des services de reconnaissance géotechnique selon les normes EN 1997‑1 et EN 1997‑2.
Les essais pressiométriques autoforés couvrent la mesure in situ la déformation d'un sol ou d'une roche tendre produite par l'expansion et la contraction d'une sonde cylindrique à membrane souple sous l'effet de la pression.

Geotehnično preiskovanje in preskušanje - Preskušanje na terenu - 6. del: Preskus s samouvrtanim presiometrom (ISO 22476-6:2018)

Ta dokument zajema zahteve za preiskovanje zemljine in šibkih kamnin s preskusi s samouvrtanim presiometrom (SBP) kot del storitev geotehničnega preiskovanja v skladu s standardoma EN 1997-1 in EN 1997-2. Preskusi s samouvrtanim presiometrom zajemajo meritve deformacije zemljin in šibkih kamnin na kraju samem s širjenjem in krčenjem valjaste fleksibilne membrane pod tlakom. Samouvrtani presiometer se uvrta v tla z vgrajeno samouvrtalno glavo na spodnjem koncu na ta način, da sonda zamenja material, ki ga odstrani, in tako ustvari lastno preskusno luknjo ter zmanjša spremembe konfiguracije zemljine zunaj instrumenta. Pritisk na sondo in povezano širjenje sonde se izmerita in zabeležita, da se pridobi razmerje med napetostjo ter izpodrivom zemljine med preskusom. Med vrtanjem in preskušanjem se podatki samodejno beležijo.

General Information

• Status: Published
• Publication Date: 23-Oct-2018
• Withdrawal Date: 29-Apr-2019
• ICS: 93.020 - Earthworks. Excavations. Foundation construction. Underground works
• Technical Committee: CEN/TC 341 - Geotechnical Investigation and Testing
• Drafting Committee: CEN/TC 341/WG 5 - Borehole expansion tests
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 24-Oct-2018
• Due Date: 03-May-2019
• Completion Date: 24-Oct-2018
• Ref Project: SIST EN ISO 22476-6:2018 - Geotechnical investigation and testing - Field testing - Part 6: Self boring pressuremeter test (ISO 22476-6:2018)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 22476-6:2018
01-december-2018
*HRWHKQLþQRSUHLVNRYDQMHLQSUHVNXãDQMH3UHVNXãDQMHQDWHUHQXGHO3UHVNXV
VVDPRXYUWDQLPSUHVLRPHWURP,62
Geotechnical investigation and testing - Field testing - Part 6: Self boring pressuremeter
test (ISO 22476-6:2018)
Geotechnische Erkundung und Untersuchung - Felduntersuchungen - Teil 6:
Selbstbohrender Pressiometerversuch (ISO 22476-6:2018)
Reconnaissance et essais géotechniques - Essais en place - Partie 6: Essai
pressiométrique autoforé (ISO 22476-6:2018)
Ta slovenski standard je istoveten z: EN ISO 22476-6:2018
ICS:
93.020 Zemeljska dela. Izkopavanja. Earthworks. Excavations.
Gradnja temeljev. Dela pod Foundation construction.
zemljo Underground works
SIST EN ISO 22476-6:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 22476-6:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 22476-6:2018


EN ISO 22476-6
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2018
EUROPÄISCHE NORM
ICS 93.020
English Version

Geotechnical investigation and testing - Field testing - Part
6: Self boring pressuremeter test (ISO 22476-6:2018)
Reconnaissance et essais géotechniques - Essais en Geotechnische Erkundung und Untersuchung -
place - Partie 6: Essai pressiométrique autoforé (ISO Felduntersuchungen - Teil 6: Selbstbohrender
22476-6:2018) Pressiometerversuch (ISO 22476-6:2018)
This European Standard was approved by CEN on 1 October 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22476-6:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 22476-6:2018
EN ISO 22476-6:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 22476-6:2018
EN ISO 22476-6:2018 (E)
European foreword
This document (EN ISO 22476-6:2018) has been prepared by Technical Committee ISO/TC 182
"Geotechnics" in collaboration with Technical Committee CEN/TC 341 “Geotechnical Investigation and
Testing” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 22476-6:2018 has been approved by CEN as EN ISO 22476-6:2018 without any
modification.


3

---------------------- Page: 5 ----------------------

SIST EN ISO 22476-6:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 22476-6:2018
INT
...