FprEN 13763-1
(Main)Explosives for civil uses - Detonators and detonating cord relays - Part 1: Requirements
Explosives for civil uses - Detonators and detonating cord relays - Part 1: Requirements
This document specifies the requirements for electric detonators, non-electric detonators, plain detonators, electronic detonators, electronic initiation systems, surface connectors, leading wires, shock tubes, coupling accessories and detonating cord relays.
This document specifies classification for electric detonators.
This document does not cover devices and accessories for reliable and safe function of detonators and relays; for this, see EN 13763 26:2004.
Explosivstoffe für zivile Zwecke - Zünder und Verzögerungselemente - Teil 1: Anforderungen
Dieses Dokument legt die Anforderungen an elektrische Zünder, nicht-elektrische Zünder, Sprengkapseln, elektronische Zünder, elektronische Zündsysteme, Oberflächenverbinder, Zünderdrähte, Zündschläuche, Verbinder und Sprengschnurverzögerer fest.
Dieses Dokument legt die Klassifizierung von elektrischen Zündern fest.
Dieses Dokument behandelt keine Geräte und Zubehörteile, die für die zuverlässige und sichere Funktionsweise von Zündern und Verzögerungselementen zuständig sind; hierzu siehe EN 13763 26:2004.
Explosifs à usage civil - Détonateurs et relais pour cordeau détonant - Partie 1 : Exigences
Le présent document spécifie les exigences relatives aux détonateurs électriques et non électriques, aux charges de détonateurs, aux détonateurs électroniques, aux systèmes d’amorçage électronique, aux connecteurs de surface, aux fils d’amorce, aux tubes à transmission d’ondes de choc, aux manchons d’accouplement et aux relais pour cordeau détonant.
Il spécifie également la classification des connecteurs électriques.
Le présent document ne couvre pas les dispositifs et les accessoires pour la fiabilité et la sécurité de fonctionnement des détonateurs et des relais (voir l’EN 13763 26:2004).
Eksplozivi za civilno uporabo - Detonatorji in zakasnilniki - 1. del: Zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2021
Nadomešča:
SIST EN 13763-1:2004
Eksplozivi za civilno uporabo - Detonatorji in zakasnilniki - 1. del: Zahteve
Explosives for civil uses - Detonators and relays - Part 1: Requirements
Explosivstoffe für zivile Zwecke - Zünder und Verzögerungselemente - Teil 1:
Anforderungen
Explosifs à usage civil - Détonateurs et relais - Partie 1 : Exigences
Ta slovenski standard je istoveten z: prEN 13763-1
ICS:
71.100.30 Eksplozivi. Pirotehnika in Explosives. Pyrotechnics and
ognjemeti fireworks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
prEN 13763-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2021
ICS 71.100.30 Will supersede EN 13763-1:2004
English Version
Explosives for civil uses - Detonators and detonating cord
relays - Part 1: Requirements
Explosifs à usage civil - Détonateurs et relais - Partie 1 : Explosivstoffe für zivile Zwecke - Zünder und
Exigences Verzögerungselemente - Teil 1: Anforderungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 321.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13763-1:2021 E
worldwide for CEN national Members.
prEN 13763-1:2021 (E)
Contents Page
European foreword . 3
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Requirements . 8
4.1 General. 8
4.2 Thermal stability at elevated temperatures . 12
4.3 Sensitiveness to impact . 12
4.4 Resistance to abrasion . 12
4.5 Resistance to cutting damage . 13
4.6 Resistance to cracking of insulation in low temperatures . 13
4.7 Mechanical strength . 13
4.8 Resistance to vibration . 14
4.9 Resistance to bending . 14
4.10 Resistance to damage by dropping . 14
4.11 Resistance to hydrostatic pressure . 14
4.12 Resistance to electrostatic discharge . 15
4.13 Equivalent initiating capability . 15
4.14 Delay accuracy . 16
4.15 No-fire current . 16
4.16 Series firing current . 16
4.17 Firing impulse . 16
4.18 Total electrical resistance . 16
4.19 Flash-over voltage . 16
4.20 Capacitance, insulation resistance and insulation breakdown . 17
4.21 Shock wave velocity . 17
4.22 Electrical non-conductivity . 17
4.23 Transfer capability . 17
4.24 Requirement for risk analysis electronic initiation systems . 17
4.25 Determination of resistance against electrostatic discharge . 18
4.26 Determination of resistance to overvoltage . 18
4.27 Determination of resistance to dynamic pressure . 18
4.28 Insulation resistance between exposed conducting parts . 19
4.29 Insulation resistance between exposed conducting parts . 19
4.30 Slow temperature change . 19
4.31 Rapid temperature change . 19
4.32 Determination of delay accuracy . 19
4.33 Determination of electromagnetic compatibility . 19
4.34 Climatic and mechanical test of electronic initiation systems . 20
4.35 Resistance to corrosion . 22
Annex A (normative) Classification of electric detonators . 23
Annex B (normative) Bruceton method . 24
Annex C (normative) PROBIT TEST (PBBS test) . 27
Annex D (informative) Classification of defects . 33
Bibliography . 42
prEN 13763-1:2021 (E)
European foreword
This document (prEN 13763-1:2021) has been prepared by Technical Committee CEN/TC 321
“Explosives for civil uses”, the secretariat of which is held by UNE.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13763-1:2004.
In comparison with the previous edition, the following technical modifications have been made:
a) Clause 1 Scope, these products have been specified: electric detonators, non-electric detonators,
plain detonators, electronic detonators, electronic initiation systems, leading wires and coupling
accessories. The scope also includes the classification for electric detonators;
b) Clause 2 Normative references, was updated;
c) Clause 4 Requirements, each subclause contain subclauses for each product. Requirements are given
for each product in the scope including the different types of detonators;
d) Clause 4.1 Requirement general, has been added. It contains a table showing what tests are required
for each product specified in the scope;
e) Clause 4.2 Thermal stability, 4.2.1 Electric detonators, non-electric detonators, electronic detonators,
plain detonators, surface connectors and detonating cord relays, the requirement has been changed
from “no detonation” to “no explosion or evidence of reaction, visible or audible”; “Evidence of
reaction” is defined in prEN 13857-1:2021;
f) Clause 4.2 Thermal stability, 4.2.2 Shock tubes, the requirement has been changed from “no visible
evidence of reaction” to “no initiation or evidence of reaction, visible or audible”; “Evidence of
reaction” is defined in prEN 13857-1:2021;
g) Clause 4.4 Resistance to abrasion, the requirement contains a clarification of the relationship with
the categories in Table 2;
h) Clause 4.7 Mechanical strength, the requirements have been listed for these two subclauses 4.7.1
Electric detonators and electronic detonators with leading wires and 4.7.2 Non-electric detonators
and electronic detonators with shock tube;
i) Clause 4.8 Resistance to vibration, the following requirement has been added: “during the vibration
test no plain detonators or semi-finished detonators shall explode”;
j) Clause 4.9 Resistance to bending, the requirement includes electronic detonators and has been
changed from “no detonator shall initiate” to “no detonator shall explode”. The following
requirement has been added: “in the functional test all detonators shall detonate”;
k) Clause 4.10 Resistance to damage by dropping, the requirement has changed from “detonate” to
explode” and from “fire to “detonate”;
l) Clause 4.11 Resistance to hydrostatic pressure, requirements for electronic detonators have been
added;
m) Clause 4.13 Equivalent initiating capability, the requirements for mean shock energy has been
replaced with requirements for mean peak pressure and requirement for mean pressure per time;
prEN 13763-1:2021 (E)
n) Clause 4.14 Delay accuracy, the requirement has changed from “all detonators shall fire” to “all
detonators shall detonate”;
o) Clause 4.19 Flash over voltage, the requirement has changed from “no detonator shall be initiated”
to “no detonator shall explode”;
p) Clause 4.23 Transfer capability, the receptors have been divided into two types, shock tubes and
detonating cord relays;
q) Clause 4.24 Requirement for risk analysis electronic initiation systems, new requirement has been
added. There was no requirement for risk analysis in the previous edition of the document;
r) Clause 4.25 Resistance against electrostatic discharge, new requirement has been added. There was
no requirement for resistance against electrostatic discharge in the previous edition of the document;
s) Clause 4.26 Determination of resistance to overvoltage, new requirement has been added. There was
no requirement for resistance to overvoltage in the previous edition of the document;
t) Clause 4.27 Determination or resistance to dynamic pressure, new requirement has been added.
There was no requirement for resistance to dynamic pressure in the previous edition of the
document;
u) Clause 4.28 Insulation resistance between exposed conducting parts, new requirement has been
added. There was no requirement for insulation resistance in the previous edition of the document;
v) Clause 4.29 Insulation resistance between exposed conducting parts, new requirement has been
added. There was no requirement for insulation resistance in the previous edition of the document;
w) Clause 4.30 Slow temperature change, new requirement has been added. There was no requirement
for slow temperature change in the previous edition of the document;
x) Clause 4.31 Rapid temperature change, new requirement has been added. There was no requirement
for rapid temperature change in the previous edition of the document;
y) Clause 4.32 Determination of delay accuracy, new requirement has been added. There was no
requirement for delay accuracy in the previous edition of the document;
z) Clause 4.33 Determination of electromagnetic compatibility, new requirement has been added.
There was no requirement for electromagnetic compatibility in the previous edition of the document;
aa) Clause 4.34 Climatic and m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.