EN 10111:2008
(Main)Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions
Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions
This European Standard specifies the grades of continuously hot rolled low carbon steel sheet and strip (in coils) for cold forming.
Depending on its actual width, strip is classified as:
- hot rolled wide strip if its width is greater than or equal to 600 mm;
- hot rolled slit wide strip if its width is less than 600 mm.
For each grade, it specifies the chemical composition and the mechanical properties.
This European Standard is applicable to products of thickness not less than 1,0 mm and not exceeding 11 mm.
This European Standard is not applicable to products covered by other standards, such as:
- hot rolled products of non-alloy structural steels for general use (see EN 10025 all parts);
- steel sheet for pressure purposes (see EN 10028 all parts);
- steel sheet for welded gas cylinders (see EN 10120);
- quenched and tempered steels (see EN 10083-1 and EN 10083-2).
Kontinuierlich warmgewalztes Band und Blech aus weichen Stählen zum Kaltumformen - Technische Lieferbindungen
Diese Europäische Norm gilt für kontinuierlich warmgewalztes Blech und Band (in Rollen) aus weichen
Stählen zum Kaltumformen.
Nach seiner tatsächlichen Breite wird das Band unterteilt nach:
- Warmbreitband mit Breiten ≥ 600 mm und
- längsgeteiltes Warmbreitband mit Breiten < 600 mm.
Diese Europäische Norm enthält für jede Stahlsorte die Anforderungen an die chemische Zusammensetzung
und die mechanischen Eigenschaften.
Diese Europäische Norm gilt für Erzeugnisse in Dicken ≥ 1,0 mm und ≤ 11 mm.
Diese Europäische Norm gilt nicht für Erzeugnisse, die in anderen Normen erfasst sind, z. B.:
- warmgewalzte Erzeugnisse aus unlegierten Baustählen (siehe EN 10025, alle Teile);
- Flacherzeugnisse aus Stählen für Druckbehälter (siehe EN 10028, alle Teile);
- Flacherzeugnisse aus Stählen für geschweißte Gasflaschen (siehe EN 10120);
- Vergütungsstähle (siehe EN 10083-1 und EN 10083-2).
Tôles et bandes en acier à bas carbone laminées à chaud en continu pour formage à froid - Conditions techniques de livraison
La présente Norme européenne détermine les nuances des tôles et bandes en acier doux (en bobines) laminées à chaud en continu pour formage à froid.
Suivant sa largeur réelle, les bandes sont classées en :
- larges bandes à chaud dont la largeur est supérieure ou égale à 600 mm ;
- larges bandes à chaud refendues dont la largeur est inférieure à 600 mm.
L présente Norme européenne spécifie la composition chimique et les propriétés mécaniques de chaque nuance.
Elle s’applique à des produits dont l’épaisseur est au moins égale à 1,0 mm et au plus 11 mm.
La présente Norme européenne ne s’applique pas aux produits couverts par d’autres normes, tels que :
- les produits laminés à chaud en acier de construction non allié d’usage général (voir toutes les parties de l’EN 10025) ;
- les tôles en acier pour appareils à pression (voir toutes les parties de l’EN 10028) ;
- les tôles en acier pour bouteilles à gaz soudées (voir l’EN 10120) ;
les aciers pour trempe et revenu (voir l’EN 10083-1 et l’EN 10083-2).
Kontinuirno vroče valjane pločevine in trakovi iz maloogljičnega jekla za preoblikovanje v hladnem - Tehnični dobavni pogoji
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditionsBandes et tôles laminées a chaud en continu, en acier doux pour emboutissage ou pliage a froid - Conditions techniques de livraisonKontinuierlich warmgewalztes Band und Blech aus weichen Stählen zum Kaltumformen - Technische Lieferbindungen77.140.50SROL]GHONLFlat steel products and semi-productsICS:SIST EN 10111:2008en,deTa slovenski standard je istoveten z:EN 10111:200801-junij-2008SIST EN 10111:2008SLOVENSKI
STANDARDSIST EN 10111:19981DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10111April 2008ICS 77.140.50Supersedes EN 10111:1998
English VersionContinuously hot rolled low carbon steel sheet and strip for coldforming - Technical delivery conditionsTôles et bandes en acier doux laminées à chaud en continupour formage à froid - Conditions techniques de livraisonKontinuierlich warmgewalztes Band und Blech aus weichenStählen zum Kaltumformen - Technische LieferbindungenThis European Standard was approved by CEN on 29 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10111:2008: E
The choice of steel grade and product type is left to the purchaser. For this choice, the purchaser may be advised by the manufacturer, but without any liability on the part of the latter, unless agreed at the time of enquiry and order. Hot rolled products are classified into four grades DD11, DD12, DD13 and DD14 defined by chemical composition, mechanical and forming characteristics (see Table 1). 4.2 Designation 4.2.1
The steel names are in compliance with EN 10027-1; the steel numbers, with EN 10027-2. 4.2.2 Products conforming to this European Standard shall be designated, in order, in the following way: a) product designation (e.g. “strip”, “sheet” or “slit strip cut longitudinally”) in line with EN 10079; b) number of this European Standard (EN 10111); c) symbolic or numerical designation of the steel (see Table 1). EXAMPLE Strip EN 10111 – DD13
or
Strip EN 10111 – 1.0335 5 Requirements 5.1 Steelmaking and manufacturing processes Unless otherwise agreed at the time of enquiry and order, the steelmaking and manufacturing processes are left to the discretion of the manufacturer.
The purchaser shall be informed of these processes if he specifies it. 5.2 Deoxidation For grade DD11 the method of deoxidation shall be at the manufacturer’s discretion. Grades DD12, DD13 and DD14 shall be fully killed. 5.3 Chemical composition Table 1 gives the permissible chemical composition limits in the cast. 5.4 Delivery conditions 5.4.1 The products shall usually be delivered with their surface as rolled. By agreement at the time of enquiry and order, the products may be delivered with descaled surface. When they are delivered as rolled, they are covered with a thin layer of scale of variable coloration. The products may be supplied with a light skin-pass, either at the manufacturer’s discretion or by agreement at the time of enquiry and order.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.