EN 13523-20:2004

Coil coated metals - Test methods - Part 20: Foam adhesion

This part of EN 13523 describes a laboratory method for testing foam adhesion to an organic coating on a metallic substrate under dry and wet conditions.

Bandbeschichtete Metalle - Prüfverfahren - Teil 20: Haftfestigkeit von Schaum

Tôles prélaquées - Méthodes d'essai - Partie 20: Adhérence des mousses

La présente partie de l'EN 13523 décrit le mode opératoire de détermination de la résistance à l'adhérence et/ou au marbrage d'un revêtement organique appliqué sur un subjectile métallique.
La pression appliquée sur un rouleau ou une pile de tôles peut affecter la surface du revêtement et provoquer des marques de transfert de brillant, la migration de plastifiant, le changement de couleur, etc., voire un phénomène d'adhérence/de collage.
Les formes plus légères de marbrage sont normalement éliminées par un chauffage modéré (par exemple par exposition au soleil).

Kovine, prevlečene v svitkih - Preskusne metode - 20. del: Oprijemljivost pene

General Information

• Status: Withdrawn
• Publication Date: 16-Nov-2004
• Withdrawal Date: 06-Dec-2011
• ICS: 25.220.60 - Organic coatings
• Technical Committee: CEN/TC 139 - Paints and varnishes
• Drafting Committee: CEN/TC 139/WG 9 - Testing of coil coated metals
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 07-Dec-2011
• Completion Date: 07-Dec-2011
• Ref Project: SIST EN 13523-20:2005 - Coil coated metals - Test methods - Part 20: Foam adhesion

Relations

• Replaced By: EN 13523-20:2011 - Coil coated metals - Test methods - Part 20: Foam adhesion
• Effective Date: 14-Dec-2011

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2005
.RYLQHSUHYOHþHQHYVYLWNLK3UHVNXVQHPHWRGHGHO2SULMHPOMLYRVWSHQH
Coil coated metals - Test methods - Part 20: Foam adhesion
Bandbeschichtete Metalle - Prüfverfahren - Teil 20: Haftfestigkeit von Schaum
Tôles prélaquées - Méthodes d'essai - Partie 20: Adhérence des mousses
Ta slovenski standard je istoveten z: EN 13523-20:2004
ICS:
25.220.60 Organske prevleke Organic coatings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13523-20
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 25.220.60
English version
Coil coated metals - Test methods - Part 20: Foam adhesion
Tôles prélaquées - Méthodes d'essais - Partie 20: Bandbeschichtete Metalle - Prüfverfahren - Teil 20:
Adhérence des mousses Haftfestigkeit von Schaum
This European Standard was approved by CEN on 23 September 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-20:2004: E
worldwide for CEN national Members.

Foreword
This document (EN 13523-20:2004) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by May 2005, and conflicting national standards shall be withdrawn at the latest by
May 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
1 Scope
This part of EN 13523 describes a laboratory method for testing foam adhesion to an organic coating on a metallic
substrate under dry and wet conditions.

2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 13523-0:2001, Coil coated metals — Test methods — Part 0: General introducti
...