EN ISO 14527-1:1999

Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14527-1:1999)

1.1 This part of ISO 14527 establishes a data block system for the designation of urea-formaldehyde and
urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs).
1.2 The various types of UF- and UF/MF-PMC are differentiated from each other by a classification system
based on information about the filler/reinforcement type and content, the intended method of processing, any
special properties and those of the special properties used specifically for designation purposes (designatory
properties).
1.3 This part of ISO 14527 is applicable to all UF- and UF/MF-PMCs ready for normal use in the form of powder,
granules or ground material.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 14527 does not provide engineering data, performance data or data on processing
conditions which may be required to specify a material for a particular application and/or method of processing. If
such additional properties are required, they shall be determined in accordance with the test methods specified in
ISO 14527-2, if suitable.
1.5 Whenever general requirement data, as covered by ISO 14527-3, need to be indicated, this is also done
using this data block system.
1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the
system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the
secretariats of ISO/TC 61/SC 1, SC 12 and SC 13.

Kunststoffe - Rieselfähige Harnstoff-Formaldehyd und Harnstoff/Melamin-Formaldehyd-Formmassen (UF- und UF/MF-PMC) - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 14527-1:1999)

1.1 In diesem Teil von ISO 14527 wird ein Daten-Blocksystem zur Bezeichnung von rieselfähigen Harnstoff-Formaldehyd- und Harnstoff/Melamin-Formaldehyd- Formmassen (UF- und UF/MF-PMC) festgelegt. 1.2 Die verschiedenen Typen von Harnstoff-Formaldehyd- und Harnstoff/Melamin-Formaldehyd-Formmassen (UF- und UF/MF-PMC) werden mit einem Einteilungssystem voneinander unterschieden, das auf Angaben über Füll/Verstärkungsstoffanteil und Art, vorgesehene Verarbeitungs- und/oder Herstellungsverfahren, Angaben zu besonderen Eigenschaften und jenen besonderen Eigenschaften beruht...

Plastiques - Poudres à mouler à base d'urée-formaldéhyde et d'urée/mélamine-formaldéhyde (UF- et UF/MF-PMC) - Partie 1: Système de désignation et base de spécification (ISO 14527-1999)

1.1 La présente partie de l'ISO 14527 établit un système de blocs de données pour la désignation des poudres à
mouler à base d'urée-formaldéhyde et d'urée/mélamine-formaldéhyde (UF- et UF/MF-PMC).
1.2 Les types d'UF- et UF/MF-PMC sont différenciés les uns des autres par un système de classification basé
sur des informations relatives à la nature et à la teneur en charges/matériaux de renforcement, à la méthode de
mise en oeuvre prévue, aux propriétés particulières en général et à celles utilisées spécifiquement pour les besoins
de la désignation (propriétés de désignation).
1.3 La présente partie de l'ISO 14527 est applicable à tous les UF- et UF/MF-PMC prêts à l'emploi pour un
usage courant sous forme de poudres, grains ou matériaux broyés.
1.4 Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les
mêmes performances. La présente partie de l'ISO 14527 ne comporte pas de données sur la conception, les
performances ou les conditions de mise en oeuvre qui peuvent être exigées pour spécifier un matériau pour une
application et/ou une méthode de mise en oeuvre particulière. Si de telles caractéristiques supplémentaires sont
nécessaires, elles doivent être déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 14527-2, le
cas échéant.
1.5 Chaque fois qu'il est nécessaire d'indiquer certaines exigences générales telles que traitées dans
l'ISO 14527-3, on utilise pour ce faire le présent système de blocs de données.
1.6 Pour garantir que la signification des lettres-codes et des nombres-codes demeure non ambiguë et pour
éviter toute contradiction au sein du système, les nouveaux lettres-codes et nombres-codes à utiliser dans les
blocs de données 1, 2 ou 3 doivent être approuvés par les secrétariats de l'ISO/TC 61/SC 1, SC 12 et SC 13 avant
utilisation.

Polimerni materiali - Sečnina-formaldehidne in sečnina/melamin-formaldehidne praškaste zmesi za oblikovanje (UF- in UF/MF- PMCs) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 14527-1:1999)

General Information

• Status: Published
• Publication Date: 14-Nov-1999
• Withdrawal Date: 30-May-2000
• ICS: 83.080.10 - Thermosetting materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 15-Nov-1999
• Completion Date: 15-Nov-1999
• Ref Project: SIST EN ISO 14527-1:2000 - Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14527-1:1999)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 14527-1:2000
01-december-2000
3ROLPHUQLPDWHULDOL6HþQLQDIRUPDOGHKLGQHLQVHþQLQDPHODPLQIRUPDOGHKLGQH
SUDãNDVWH]PHVL]DREOLNRYDQMH8)LQ8)0)30&VGHO6LVWHPR]QDþHYDQMD
LQSRGODJH]DVSHFLILNDFLMH,62
Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding
compounds (UF- and UF/MF-PMCs) - Part 1: Designation system and basis for
specifications (ISO 14527-1:1999)
Kunststoffe - Rieselfähige Harnstoff-Formaldehyd und Harnstoff/Melamin-Formaldehyd-
Formmassen (UF- und UF/MF-PMC) - Teil 1: Bezeichnungssystem und Basis für
Spezifikationen (ISO 14527-1:1999)
Plastiques - Poudres a mouler a base d'urée-formaldéhyde et d'urée/mélamine-
formaldéhyde (UF- et UF/MF-PMC) - Partie 1: Systeme de désignation et base de
spécification (ISO 14527-1999)
Ta slovenski standard je istoveten z: EN ISO 14527-1:1999
ICS:
83.080.10 Duromeri Thermosetting materials
SIST EN ISO 14527-1:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14527-1:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 14527-1:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 14527-1:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 14527-1:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 14527-1:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 14527-1:2000
INTERNATIONAL ISO
STANDARD 14527-1
First edition
1999-11-15
Plastics — Urea-formaldehyde and
urea/melamine-formaldehyde powder
moulding compounds (UF- and
UF/MF-PMCs) —
Part 1:
Designation system and basis for
specifications
Plastiques — Poudres à mouler à base d'urée-formaldéhyde et
d'urée/mélamine-formaldéhyde (UF- et UF/MF-PMC) —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 14527-1:1999(E)
�
©
ISO 1999

---------------------- Page: 7 ----------------------

SIST EN ISO 14527-1:2000
ISO 14527-1:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 1999 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 14527-1:2000
ISO 14527-1:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 14527 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14527-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 12, Thermosetting materials.
After a transitio
...