EN ISO 16147:2021
(Main)Small craft - Inboard diesel engines - Engine-mounted fuel, oil and electrical components (ISO 16147:2020)
Small craft - Inboard diesel engines - Engine-mounted fuel, oil and electrical components (ISO 16147:2020)
This document establishes requirements for the design and installation of engine-mounted fuel, oil and electrical components on diesel inboard-mounted engines for minimizing fuel leakage, risk of electric shock and the risk of and/or the spread of fire on small craft of hull length up to 24 m in accordance with ISO 8666.
Kleine Wasserfahrzeuge - Eingebaute Dieselmotoren - Am Motor befestigte Kraftstoff-, Öl- und Elektrikbauteile (ISO 16147:2020)
Dieses Dokument legt Anforderungen für Konstruktion und Montage von am Motor befestigten Kraftstoff-, Öl- und Elektrikbauteilen von Innenbord Dieselmotoren fest, um die Leckage von Kraftstoff, das Risiko eines Stromschlags und das Risiko und/oder die Ausbreitung eines Feuers auf kleinen Wasserfahrzeugen bis zu einer Rumpflänge von 24 m nach ISO 8666 zu minimieren.
Petits navires - Moteurs intérieurs diesels - Éléments des circuits d'alimentation, des systèmes de lubrification et des systèmes électriques fixés sur le moteur (ISO 16147:2020)
Le présent document établit les exigences relatives à la conception et à l'installation des composants des circuits d'alimentation, des systèmes de lubrification et des systèmes électriques montés sur des moteurs intérieurs diesels, afin de réduire le plus possible les fuites de carburant, les risques de choc électrique et les risques d'incendie et/ou la propagation du feu sur les petits navires d'une longueur de coque inférieure ou égale à 24 m conformément à l'ISO 8666.
Mala plovila - Vgrajeni dizelski motorji - Nameščene komponente za gorivo, olje in elektriko (ISO 16147:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2021
Nadomešča:
SIST EN ISO 16147:2018
Mala plovila - Vgrajeni dizelski motorji - Nameščene komponente za gorivo, olje in
elektriko (ISO 16147:2020)
Small craft - Inboard diesel engines - Engine-mounted fuel, oil and electrical components
(ISO 16147:2020)
Kleine Wasserfahrzeuge - Eingebaute Dieselmotoren - Am Motor befestigte Kraftstoff-,
Öl- und Elektrikbauteile (ISO 16147:2020)
Petits navires - Moteurs intérieurs diesels - Éléments des circuits d'alimentation, des
systèmes de lubrification et des systèmes électriques fixés sur le moteur (ISO
16147:2020)
Ta slovenski standard je istoveten z: EN ISO 16147:2021
ICS:
47.020.20 Ladijski motorji Marine engines and
propulsion systems
47.080 Čolni Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 16147
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2021
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 16147:2018
English Version
Small craft - Inboard diesel engines - Engine-mounted fuel,
oil and electrical components (ISO 16147:2020)
Petits navires - Moteurs intérieurs diesels - Éléments Kleine Wasserfahrzeuge - Eingebaute Dieselmotoren -
des circuits d'alimentation, des systèmes de Am Motor befestigte Kraftstoff-, Öl- und
lubrification et des systèmes électriques fixés sur le Elektrikbauteile (ISO 16147:2020)
moteur (ISO 16147:2020)
This European Standard was approved by CEN on 3 November 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16147:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4
European foreword
This document (EN ISO 16147:2021) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of which is
held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2021, and conflicting national standards shall be
withdrawn at the latest by July 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 16147:2018.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 16147:2020 has been approved by CEN as EN ISO 16147:2021 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding Essential Requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2013/53/EU
Essential requirements (ERs) of Clauses/subclauses of Qualifying remarks/Notes
EU Directive 2013/53/EU this European Standard
Annex I, Part A, 5.1.1 - Installation 4, 5, 6 In respect of inspection of fuel, oil
requirements; inboard engine and electrical components fitted to
diesel inboard-mounted engines.
Annex I, Part A, 5.2.1 - Fuel system; 4, 5, 7 In respect of minimising the risk of
general fuel leakage and risk/spread of fire
from fuel components that are
engine mounted.
Annex I, Part A, 5.3 - Electrical 4, 6 Only in respect of minimising the
system risk/spread of fire from electrical
components that are engine
mounted.
Annex I, Part A, 5.6.1 Fire protection 4, 5, 6, 7 In respect of the design and
- General installation arrangements for
engine mounted fuel, oil and
electrical components on inboard
diesel engines.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 16147
Third edition
2020-12
Small craft — Inboard diesel engines
— Engine-mounted fuel, oil and
electrical components
Petits navires — Moteurs intérieurs diesels — Éléments des circuits
d'alimentation, des systèmes de lubrification et des systèmes
électriques fixés sur le moteur
Reference number
ISO 16147:2020(E)
©
ISO 2020
ISO 16147:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 16147:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 2
5 Engine fuel and oil system and components . 2
5.1 General . 2
5.2 High-pressure fuel pipes . 3
5.3 Low-pressure fuel lines . 3
5.4 Fuel and lubrication oil filters . 3
6 Electrical systems and components. 3
6.1 General . 3
6.2 Cranking motors . 3
6.3 Wiring and connections . 4
6.4 Relays, fuse boxes and electronic control modules (ECMs) . 4
7 Installation manual . 4
Bibliography . 5
ISO 16147:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small craft, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 464, Small craft, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition of ISO 16147 cancels and replaces the second edition (ISO 16147:2018), of which it
constitutes a minor revision. The changes compared to the previous edition are as follows:
— clarification in the Scope that the length of hull is as defined in ISO 8666, a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.