EN ISO 15876-2:2017/A1:2020
(Amendment)Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes - Amendment 1 (ISO 15876-2:2017/Amd 1:2020)
Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes - Amendment 1 (ISO 15876-2:2017/Amd 1:2020)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polybuten (PB) - Teil 2: Rohre - Änderung 1 (ISO 15876-2:2017/Amd 1:2020)
No scope available
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Polybutène (PB) - Partie 2: Tubes - Amendement 1 (ISO 15876-2:2017/Amd 1:2020)
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Polibuten (PB) - 2. del: Cevi - Dopolnilo A1 (ISO 15876-2:2017/Amd 1:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2021
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo -
Polibuten (PB) - 2. del: Cevi - Dopolnilo A1 (ISO 15876-2:2017/Amd 1:2020)
Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2:
Pipes - Amendment 1 (ISO 15876-2:2017/Amd 1:2020)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polybuten
(PB) - Teil 2: Rohre - Änderung 1 (ISO 15876-2:2017/Amd 1:2020)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide
Polybutène (PB) Partie 2: Tubes Amendement 1 (ISO 15876-2:2017/Amd 1:2020)
Ta slovenski standard je istoveten z: EN ISO 15876-2:2017/A1:2020
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 15876-2:2017/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2020
EUROPÄISCHE NORM
ICS 23.040.20; 91.140.60
English Version
Plastics piping systems for hot and cold water installations
- Polybutene (PB) - Part 2: Pipes - Amendment 1 (ISO
15876-2:2017/Amd 1:2020)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polybutène (PB) - Kaltwasserinstallation - Polybuten (PB) - Teil 2: Rohre
Partie 2: Tubes - Amendement 1 (ISO 15876- - Änderung 1 (ISO 15876-2:2017/Amd 1:2020)
2:2017/Amd 1:2020)
This amendment A1 modifies the European Standard EN ISO 15876-2:2017; it was approved by CEN on 12 October 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15876-2:2017/A1:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 15876-2:2017/A1:2020) has been prepared by Technical Committee ISO/TC
138 "Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical
Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held
by NEN.
This Amendment to the European Standard EN ISO 15876-2:2017 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by June 2021, and
conflicting national standards shall be withdrawn at the latest by June 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15876-2:2017/Amd 1:2020 has been approved by CEN as EN ISO 15876-
2:2017/A1:2020 without any modification.
INTERNATIONAL ISO
STANDARD 15876-2
Second edition
2017-01
AMENDMENT 1
2020-12
Plastics piping systems for hot
and cold water installations —
Polybutene (PB) —
Part 2:
Pipes
AMENDMENT 1
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polybutène (PB) —
Partie 2: Tubes
AMENDEMENT 1
Reference number
ISO 15876-2:2017/Amd.1:2020(E)
©
ISO 2020
ISO 15876-2:2017/Amd.1:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.