EN ISO 15876-5:2017/A1:2020
(Amendment)Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 15876-5:2017/Amd 1:2020)
Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 15876-5:2017/Amd 1:2020)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polybuten (PB) - Teil 5: Gebrauchstauglichkeit des Systems - Änderung 1 (ISO 15876-5:2017/Amd 1:2020)
No scope available
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Polybutène (PB) - Partie 5: Aptitude à l'emploi du système - Amendement 1 (ISO 15876-5:2017/Amd 1:2020)
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Polibuten (PB) - 5. del: Ustreznost sistema namenu - Dopolnilo A1 (ISO 15876-5:2017/Amd 1:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15876-5:2017/A1:2021
01-februar-2021
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo -
Polibuten (PB) - 5. del: Ustreznost sistema namenu - Dopolnilo A1 (ISO 15876-
5:2017/Amd 1:2020)
Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5:
Fitness for purpose of the system - Amendment 1 (ISO 15876-5:2017/Amd 1:2020)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polybuten
(PB) - Teil 5: Gebrauchstauglichkeit des Systems - Änderung 1 (ISO 15876-5:2017/Amd
1:2020)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polybutène (PB) - Partie 5: Aptitude à l'emploi du système - Amendement 1 (ISO 15876-
5:2017/Amd 1:2020)
Ta slovenski standard je istoveten z: EN ISO 15876-5:2017/A1:2020
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 15876-5:2017/A1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15876-5:2017/A1:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 15876-5:2017/A1:2021
EN ISO 15876-5:2017/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2020
EUROPÄISCHE NORM
ICS 23.040.20; 91.140.60
English Version
Plastics piping systems for hot and cold water installations
- Polybutene (PB) - Part 5: Fitness for purpose of the
system - Amendment 1 (ISO 15876-5:2017/Amd 1:2020)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polybutène (PB) - Kaltwasserinstallation - Polybuten (PB) - Teil 5:
Partie 5: Aptitude à l'emploi du système - Amendement Gebrauchstauglichkeit des Systems - Änderung 1 (ISO
1 (ISO 15876-5:2017/Amd 1:2020) 15876-5:2017/Amd 1:2020)
This amendment A1 modifies the European Standard EN ISO 15876-5:2017; it was approved by CEN on 12 October 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15876-5:2017/A1:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15876-5:2017/A1:2021
EN ISO 15876-5:2017/A1:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15876-5:2017/A1:2021
EN ISO 15876-5:2017/A1:2020 (E)
European foreword
This document (EN ISO 15876-5:2017/A1:2020) has been prepared by Technical Committee ISO/TC
138 "Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical
Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held
by NEN.
This Amendment to the European Standard EN ISO 15876-5:2017 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by June 2021, and
conflicting national standards shall be withdrawn at the latest by June 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Est
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.