EN ISO 4753:2011
(Main)Fasteners - Ends of parts with external ISO metric thread (ISO 4753:2011)
Fasteners - Ends of parts with external ISO metric thread (ISO 4753:2011)
ISO 4753:2011 specifies the form and dimensions of ends of parts with external ISO metric screw thread (e.g. bolt, screw and stud ends) recommended for use. They apply to standardized or non-standardized threaded parts.
For each end type, a symbol is specified and it is intended that these symbols be used when specifying one of the ends for threaded fasteners.
Mechanische Verbindungselemente - Enden von Teilen mit metrischem ISO-Außengewinde (ISO 4753:2011)
Diese Internationale Norm legt Form und Maße von Enden von Teilen mit metrischem ISO-Außengewinde (z. B. Schraubenenden) fest, die zur Anwendung empfohlen werden. Sie gelten für genormte und nichtgenormte Teile mit Gewinde, sofern sie bei der Bestellung angegeben werden. Für jedes Ende ist ein Symbol festgelegt und es wird empfohlen, diese Symbole bei Bestellung eines dieser Enden für Verbindungselemente mit Gewinde zu verwenden.
Éléments de fixation - Extrémités des éléments à filetage extérieur métrique ISO (ISO 4753:2011)
L'ISO 4753:2011 spécifie la forme et les dimensions des extrémités des éléments à filetage extérieur métrique ISO (par exemple extrémités de vis) d'usage recommandé. Elle s'applique aux éléments filetés normalisés ou non, lorsque cela est spécifié à la commande.
Un symbole est défini pour chaque sorte d'extrémité et il est prévu d'utiliser ces symboles pour spécifier l'extrémité souhaitée d'un élément de fixation fileté.
Mehanski vezni elementi - Končine vijakov z zunanjim metrskim navojem po ISO (ISO 4753:2011)
Ta mednarodni standard določa formo in dimenzije vijakov s končinami vijakov z zunanjimi metrskimi navoji (npr. sorniki, vijaki in stojni vijaki), priporočenih za uporabo. Veljajo za standardizirane ali nestandardizirane dele z navojem. Za vsak tip končine je določen simbol in mišljeno je, da se ti simboli uporabijo pri določanju enega od končin mehanskih vezanih elementov z navojem.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2012
1DGRPHãþD
SIST EN ISO 4753:2001
0HKDQVNLYH]QLHOHPHQWL.RQþLQHYLMDNRY]]XQDQMLPPHWUVNLPQDYRMHPSR,62
,62
Fasteners - Ends of parts with external ISO metric thread (ISO 4753:2011)
Mechanische Verbindungselemente - Enden von Teilen mit metrischem ISO-
Außengewinde (ISO 4753:2011)
Éléments de fixation - Extrémités des éléments à filetage extérieur métrique ISO (ISO
4753:2011)
Ta slovenski standard je istoveten z: EN ISO 4753:2011
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 4753
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2011
ICS 21.060.01 Supersedes EN ISO 4753:1999
English Version
Fasteners - Ends of parts with external ISO metric thread (ISO
4753:2011)
Éléments de fixation - Extrémités des éléments à filetage Mechanische Verbindungselemente - Enden von Teilen mit
extérieur métrique ISO (ISO 4753:2011) metrischem ISO-Außengewinde (ISO 4753:2011)
This European Standard was approved by CEN on 31 October 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4753:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 4753:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the
latest by May 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4753:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 4753:2011 has been approved by CEN as a EN ISO 4753:2011 without any modification.
INTERNATIONAL ISO
STANDARD 4753
Third edition
2011-11-01
Fasteners — Ends of parts with external
ISO metric thread
Éléments de fixation — Extrémités des éléments à filetage extérieur
métrique ISO
Reference number
ISO 4753:2011(E)
©
ISO 2011
ISO 4753:2011(E)
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 4753:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules g
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.