EN ISO 14921:2010
(Main)Thermal spraying - Procedures for the application of thermally sprayed coatings for engineering components (ISO 14921:2010)
Thermal spraying - Procedures for the application of thermally sprayed coatings for engineering components (ISO 14921:2010)
ISO 14921:2010 specifies the general procedure, when a thermally sprayed coating is applied to enhance the surface properties of a component or to reclaim worn and non-conforming parts.
ISO 14921:2010 does not provide definitive methods for specific work due to the variety of the technological, physical and/or chemical requirements and of the component's shape.
ISO 14921:2010 specifies the general conditions for the selection of the spraying procedure and materials for this purpose. ISO 14921:2010 does not apply to thermally sprayed zinc and/or aluminium coatings for protection of steel structures against atmospheric corrosion, for which ISO 2063 applies.
ISO 14921:2010 also does not apply to coatings of self-fluxing alloys which are subsequently fused. That procedure is covered by ISO 14920.
Thermisches Spritzen - Vorgehen für das Anwenden thermischer Spritzschichten für Bauteile im Maschinenbau (ISO 14921:2010)
Diese Internationale Norm legt die generelle Vorgehensweise fest, wenn thermisch gespritzte Schichten zur
Reparatur verschlissener und nicht passender Teile oder der Verbesserung der Oberflächeneigenschaften
von Bauteilen angewendet werden.
Diese Internationale Norm legt aufgrund der Vielfalt an technologischen, physikalischen und/oder chemischen
Anforderungen und der Bauteilgeometrie keine bestimmten Verfahren für spezielle Arbeiten fest.
Diese Internationale Norm legt allgemeine Auswahlbedingungen für das Spritzverfahren und Werkstoffe fest.
Sie gilt nicht für thermisch gespritzte Zink- und/oder Aluminiumschichten für den Schutz von
Stahlkonstruktionen gegen atmosphärische Korrosion, hierfür gilt ISO 2063.
Diese Internationale Norm gilt ebenfalls nicht für Schichten aus selbstfließenden Legierungen mit
anschließendem Umschmelzen, die durch ISO 14920 abgedeckt sind.
Projection thermique - Mode opératoire d'application de revêtements obtenus par projection thermique pour les pièces mécaniques (ISO 14921:2010)
L'ISO 14921:2010 spécifie le mode opératoire général à suivre lorsqu'un revêtement obtenu par projection thermique est appliqué pour améliorer les propriétés de la surface d'une pièce ou pour récupérer des pièces usées et non conformes.
Compte tenu de la diversité des exigences technologiques, physiques et/ou chimiques et de la forme de la pièce, il convient de ne pas utiliser l'ISO 14921:2010 pour fournir des méthodes reconnues pour une pièce à traiter spécifique.
L'ISO 14921:2010 spécifie les conditions générales pour le choix du mode opératoire de projection et des matériaux à utiliser cet effet. Elle n'est pas applicable aux revêtements de zinc et/ou d'aluminium obtenus par projection thermique destinés à protéger les structures en acier contre la corrosion atmosphérique, pour lesquels l'ISO 2063 est applicable.
L'ISO 14921:2010 ne s'applique pas non plus aux revêtements en alliages auto-fondants qui sont fondus à une étape ultérieure. Ce mode opératoire relève de l'ISO 14920.
Vroče brizganje - Postopki nanašanja vroče brizganih prevlek na strojne dele (ISO 14921:2010)
Ta mednarodni standard določa splošni postopek za nanos vroče brizgane prevleke, ki okrepi površinske lastnosti strojnega dela ali izboljša obrabljene in neskladne strojne dele. Ta mednarodni standard zaradi različnih tehnoloških, fizikalnih in/ali kemijskih zahtev in oblike strojnih delov ne podaja definitivnih metod za konkretno delo. Ta mednarodni standard določa splošne pogoje za izbiro postopka in materiale brizganja. Ne velja za vroče brizgane cinkove in/ali aluminijeve prevleke za zaščito jeklenih struktur pred atmosfersko korozijo, za kar velja ISO 2063. Ta mednarodni standard tudi ne velja za prevleke iz samotaljivih zlitin, ki se v nadaljevanju stalijo. Ta postopek je zajet v ISO 14920.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2012
1DGRPHãþD
SIST EN ISO 14921:2002
9URþHEUL]JDQMH3RVWRSNLQDQDãDQMDYURþHEUL]JDQLKSUHYOHNQDVWURMQHGHOH ,62
Thermal spraying - Procedures for the application of thermally sprayed coatings for
engineering components (ISO 14921:2010)
Thermisches Spritzen - Vorgehen für das Anwenden thermischer Spritzschichten für
Bauteile im Maschinenbau (ISO 14921:2010)
Projection thermique - Mode opératoire d'application de revêtements obtenus par
projection thermique pour les pièces mécaniques (ISO 14921:2010)
Ta slovenski standard je istoveten z: EN ISO 14921:2010
ICS:
25.220.20 Površinska obdelava Surface treatment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 14921
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2010
ICS 25.220.20 Supersedes EN ISO 14921:2001
English Version
Thermal spraying - Procedures for the application of thermally
sprayed coatings for engineering components (ISO 14921:2010)
Projection thermique - Mode opératoire d'application de Thermisches Spritzen - Vorgehen für das Anwenden
revêtements obtenus par projection thermique pour les thermischer Spritzschichten für Bauteile im Maschinenbau
pièces mécaniques (ISO 14921:2010) (ISO 14921:2010)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14921:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 14921:2010) has been prepared by Technical Committee CEN/TC 240 “Thermal
spraying and thermally sprayed coatings”, the secretariat of which is held by DIN, in collaboration with
Technical Committee ISO/TC 107 “Metallic and other inorganic coatings”.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2011, and conflicting national standards shall be withdrawn at
the latest by June 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14921:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
INTERNATIONAL ISO
STANDARD 14921
Second edition
2010-12-15
Thermal spraying — Procedures for the
application of thermally sprayed coatings
for engineering components
Projection thermique — Mode opératoire d'application de revêtements
obtenus par projection thermique pour les pièces mécaniques
Reference number
ISO 14921:2010(E)
©
ISO 2010
ISO 14921:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 14921:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Component and coating design considerations.1
4.1 General .1
4.2 Pre-inspection in the case of repair .2
4.3 Component substrate .2
4.4 Coating .2
5 Preliminary machining by turning, milling, or grinding .3
6 Masking .3
7 Methods of surface preparation.3
8 Thermal spraying.4
9 Inspection after spraying.4
10 Sealing.4
11 Finishing.4
12 Final inspection .4
13 Documentation .5
Annex A (informative) Flow chart for assessment of suitability of thermal spraying .6
Annex B (informative) Check list for evaluation of the most suitable coating system for the
intended purpose .7
Annex C (informative) Record for the applied thermal spray procedure .8
Bibliography.12
ISO 14921:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14921 was prepared by Technical Committee CEN/TC 240, Thermal spraying and thermally sprayed
coatings of the European Committee for Standardization (CEN) in collaboration with ISO Technical Committee
ISO/TC 107, Metallic and other inorganic coatings in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 14921:2001), which has been technically
revised.
iv © ISO 2010 – All rights reserved
ISO 14921:2010(E)
Introduction
Components might fail if the surface does not fulfil the physical, chemical, and/or technological requirements.
For several applications, this deficiency can be avoided by a thermally sprayed coating.
Where appropriate, a coating may be applied to protect the component's surface or to improve its behaviour
by increasing the resistance against wear and/or corrosion, or the electrical or thermal conductivity or
insulation or by reducing the friction coefficient.
There are limits to the applicable thickness of some thermally sprayed coatings. However, several different
coatings may be built up one upon another. In the case of extensive loss of material through corrosion or wear,
an alternative suitable spraying material may be applied prior to the top coat or the bond and top coat.
INTERNATIONAL STANDARD ISO 14921:2010(E)
Thermal spraying — Procedures for the application of thermally
sprayed coatings for engineering components
1 Scope
This International Standard specifies the general procedure, when a thermally sprayed coating is applied to
enhance the surface properties of a component or to reclaim worn and non-conforming parts.
This International Standard does not provide definitive methods for specific work due to the variety of the
technological, physical and/or chemical requirements and of the component's shape.
This International Standard specifies the general conditions for the selection of the spraying procedure and
materials for this purpose. It does not apply to thermally sprayed zinc and/or aluminium coatings for
protection of steel structures against atmospheric corrosion, for which ISO 2063 applies.
This International Standard also does not apply to coatings of self-fluxing alloys which are subsequently fused.
That procedure is covered by ISO 14920.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 14923, Thermal spraying — Characterization and testing of thermally sprayed coatings
EN 657:2005, Thermal spraying — Terminology, classification
EN 13507, Thermal spraying — Pre-treatment of surface of metallic parts and componen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.