prEN ISO 2719
(Main)Determination of flash point - Pensky-Martens closed cup method (ISO/DIS 2719:2024)
Determination of flash point - Pensky-Martens closed cup method (ISO/DIS 2719:2024)
ISO 2719:2016 describes three procedures, A, B and C, using the Pensky-Martens closed cup tester, for determining the flash point of combustible liquids, liquids with suspended solids, liquids that tend to form a surface film under the test conditions, biodiesel and other liquids in the temperature range of 40 °C to 370 °C.
CAUTION - For certain mixtures no flash point, as defined, is observed; instead a significant enlargement of the test flame (not halo effect) and a change in colour of the test flame from blue to yellowish-orange can occur. Continued heating can result in significant burning of vapours outside the test cup, and can be a potential fire hazard.
NOTE 1 Although, technically, kerosene with a flash point above 40 °C can be tested using this International Standard, it is standard practice to test kerosene according to ISO 13736.[5] Similarly, lubricating oils are normally tested according to ISO 2592[2].
Procedure A is applicable to distillate fuels (diesel, biodiesel blends, heating oil and turbine fuels), new and in-use lubricating oils, paints and varnishes, and other homogeneous liquids not included in the scope of Procedures B or C.
Procedure B is applicable to residual fuel oils, cutback residua, used lubricating oils, mixtures of liquids with solids, liquids that tend to form a surface film under test conditions or are of such kinematic viscosity that they are not uniformly heated under the stirring and heating conditions of Procedure A.
Procedure C is applicable to fatty acid methyl esters (FAME) as specified in specifications such as EN 14214[11] or ASTM D6751[13].
ISO 2719:2016 is not applicable to water-borne paints and varnishes.
NOTE 2 Water-borne paints and varnishes can be tested using ISO 3679[3]. Liquids containing traces of highly volatile materials can be tested using ISO 1523[1] or ISO 3679.
Bestimmung des Flammpunktes - Verfahren nach Pensky-Martens mit geschlossenem Tiegel (ISO/DIS 2719:2024)
Détermination du point d'éclair - Méthode Pensky-Martens en vase clos (ISO/DIS 2719:2024)
ISO 2719:2016 décrit trois méthodes, A, B, et C, pour la détermination du point d'éclair des liquides combustibles, des liquides contenant des matières solides en suspension, des liquides ayant tendance à former un film en surface dans les conditions d'essai, des biocarburants et d'autres liquides, au moyen de l'appareil d'essai Pensky-Martens en vase clos, dans la plage de température entre 40 °C et 370 °C.
ATTENTION ? Pour certains mélanges, aucun point d'éclair, tel que défini, n'est observé; à la place, il peut y avoir un élargissement significatif de la flamme d'essai (pas de phénomène de halo) et un changement de couleur de la flamme passant du bleu à l'orange jaunâtre. Le maintien du chauffage peut faire qu'une quantité significative de vapeurs soit brûlée à l'extérieur du vase d'essai, ce qui peut constituer un danger d'incendie.
NOTE 1 Techniquement les kérosènes ayant un point d'éclair supérieur à 40 °C peuvent être soumis à essai selon la présente Norme internationale. Cependant, il est d'usage courant de déterminer le point d'éclair des kérosènes selon l'ISO 13736[5]. De façon analogue, les huiles lubrifiantes sont normalement soumises à essai suivant l'ISO 2592[2].
La Méthode A est applicable aux distillats de pétrole (carburant diesel, mélanges de biocarburant, fioul domestique et turbocombustibles), aux huiles lubrifiantes neuves et en service, aux peintures et vernis, et à d'autres liquides homogènes ne faisant pas partie du champ d'application des Méthodes B ou C.
La Méthode B est applicable aux combustibles résiduels, aux résidus de bitumes fluidifiés, aux huiles lubrifiantes usagées, aux mélanges de liquides contenant des matières solides, aux liquides ayant tendance à former un film en surface dans les conditions d'essai ou ayant une viscosité cinématique telle qu'ils ne sont pas chauffés de manière uniforme sous agitation et dans les conditions de chauffage de la Méthode A.
La Méthode C est applicable aux esters méthyliques d'acides gras (EMAG) tels que définis dans des spécifications telles que l'EN 14214[11] ou l'ASTM D 6751[13].
La présente Norme internationale n'est pas applicable aux peintures et vernis renfermant de l'eau.
NOTE 2 Le point d'éclair des peintures et vernis renfermant de l'eau peut être déterminé suivant l'ISO 3679[3]. Les liquides contenant des traces de produits hautement volatils peuvent être analysés conformément à l'ISO 1523[1] ou l'ISO 3679.
Določevanje plamenišča - Metoda Pensky-Martens z zaprto posodo (ISO/DIS 2719:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Določevanje plamenišča - Metoda Pensky-Martens z zaprto posodo (ISO/DIS
2719:2024)
Determination of flash point - Pensky-Martens closed cup method (ISO/DIS 2719:2024)
Bestimmung des Flammpunktes - Verfahren nach Pensky-Martens mit geschlossenem
Tiegel (ISO/DIS 2719:2024)
Détermination du point d'éclair - Méthode Pensky-Martens en vase clos (ISO/DIS
2719:2024)
Ta slovenski standard je istoveten z: prEN ISO 2719
ICS:
75.080 Naftni proizvodi na splošno Petroleum products in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 2719
ISO/TC 28
Determination of flash point —
Secretariat: NEN
Pensky-Martens closed cup method
Voting begins on:
Détermination du point d'éclair — Méthode Pensky-Martens en
2024-08-19
vase clos
Voting terminates on:
ICS: 75.080 2024-11-11
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 2719:2024(en)
DRAFT
ISO/DIS 2719:2024(en)
International
Standard
ISO/DIS 2719
ISO/TC 28
Determination of flash point —
Secretariat: NEN
Pensky-Martens closed cup method
Voting begins on:
Détermination du point d'éclair — Méthode Pensky-Martens en
vase clos
Voting terminates on:
ICS: 75.080
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 2719:2024(en)
ii
ISO/DIS 2719:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Principle . 2
5 Chemicals and materials . 2
6 Apparatus . 2
7 Apparatus preparation . 3
7.1 General .3
7.2 Location of the apparatus .3
7.3 Cleaning the test cup .3
7.4 Apparatus assembly .3
7.5 Apparatus verification .3
8 Sampling . 4
9 Sample handling . 5
9.1 Petroleum products .5
9.1.1 Sub-sampling .5
9.1.2 Samples containing undissolved water.5
9.1.3 Samples that are liquid at ambient temperature .5
9.1.4 Samples that are very viscous, semi-solid or solid at ambient temperature .5
9.2 Paints and varnishes .6
10 Procedure . 6
10.1 General .6
10.2 Procedure A .6
10.3 Procedure B .7
10.4 Procedure C .8
11 Calculation . 9
11.1 Conversion of barometric pressure reading .9
11.2 Correction of detected flash point .9
12 Expression of results . 9
13 Precision . 9
13.1 General .9
13.2 Repeatability, r.9
13.3 Reproducibility, R .10
14 Test report .11
Annex A (normative) Apparatus verification using reference materials .12
Annex B (normative) Pensky-Martens closed cup test apparatus .15
Annex C (normative) Temperature measuring device specification .21
Annex D (normative) Requirements for hot wire ignitors and flash point detectors .23
Annex E (informative) Automated cover assembly .25
Bibliography .26
iii
ISO/DIS 2719:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO [had/had not] received notice of
(a) patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.