EN 1380:2009

Timber structures - Test methods - Load bearing nails, screws, dowels and bolts

This European Standard specifies test methods for determining the strength and deformation characteristics of laterally loaded connections with nail, screws, dowels and bolts in load-bearing timber structures.
The methods assess connections with members of timber (solid timber or glued laminated timber) or wood-based products or metal plates (but not punched metal plate fasteners) in the combination proposed for use in service.
The methods are used to determine load-slip characteristics and maximum load of connections where various angles between the applied force and the timber grain direction, or the main direction of the wood-based products, respectively, are possible.

Holzbauwerke - Prüfverfahren - Tragende Verbindungen mit Nägeln, Schrauben, Stabdübeln und Bolzen

In dieser Europäischen Norm werden Prüfverfahren zur Bestimmung der Festigkeits- und Verformungs-eigenschaften von auf Abscheren belasteten Verbindungen mit Nägeln, Schrauben, Stabdübeln oder Bolzen in tragenden Holzbauwerken festgelegt.
Mit den Verfahren werden Verbindungen mit Holzteilen (Vollholz oder Brettschichtholz) oder Holzwerkstoffen oder Metallblechen (jedoch keine Nagelplatten) in der für die Anwendung vorgesehenen Kombination beurteilt.
Die Verfahren dienen zur Bestimmung des Last-Verschiebungsverhaltens und der Höchstlast von Verbindungen, wobei verschiedene Winkel zwischen der einwirkenden Last und der Faserrichtung des Holzes oder der entsprechenden Hauptrichtung von Holzwerkstoffen möglich sind.

Structures en bois - Méthode d'essai - Pointes, tire-fonds, broches et boulons porteurs

La présente Norme européenne définit les méthodes d'essai permettant de déterminer les caractéristiques de
résistance et de déformation d'assemblages connectés latéralement par pointes, tire-fonds, broches et
boulons dans des structures porteuses en bois.
Les méthodes supposent l'assemblage d’éléments en bois (massif ou lamellé collé), en produits à base de
bois ou de plaques métalliques (à l'exception des connecteurs à plaque métallique emboutie) dans des
combinaisons correspondant à leur emploi en service.
Les méthodes sont utilisées pour déterminer les caractéristiques force-glissement ainsi que la charge
maximale des assemblages avec un angle quelconque entre la force appliquée et l'orientation des fibres du
bois ou de la direction principale des produits à base de bois.

Lesene konstrukcije - Metode preskušanja - Nosilni žebljani spoji

General Information

• Status: Published
• Publication Date: 31-Mar-2009
• Withdrawal Date: 30-Oct-2009
• ICS: 91.080.20 - Timber structures
• Technical Committee: CEN/TC 124 - Timber structures
• Drafting Committee: CEN/TC 124/WG 1 - Test methods
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 26-Feb-2020
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/BC/CEN/87/10 - Standardization request in the field of Construction products - timber
• Ref Project: SIST EN 1380:2009 - Timber structures - Test methods - Load bearing nails, screws, dowels and bolts

Relations

• Replaces: EN 1380:1999 - Timber structures - Test methods - Load bearing nailed joints
• Effective Date: 08-Apr-2009

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lesene konstrukcije - Metode preskušanja - Nosilni žebljani spojiHolzbauwerke - Prüfverfahren - Tragende NagelverbindungenStructures en bois - Méthode d'essai - Pointes, tire-fonds, broches et boulons porteursTimber structures - Test methods - Load bearing nails, screws, dowels and bolts91.080.20Lesene konstrukcijeTimber structuresICS:Ta slovenski standard je istoveten z:EN 1380:2009SIST EN 1380:2009en,fr,de01-september-2009SIST EN 1380:2009SLOVENSKI
STANDARDSIST EN 1380:20001DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1380April 2009ICS 91.080.20Supersedes EN 1380:1999
English VersionTimber structures - Test methods - Load bearing nails, screws,dowels and boltsStructures en bois - Méthode d'essai - Pointes, tire-fonds,broches et boulons porteursHolzbauwerke - Prüfverfahren - TragendeNagelverbindungenThis European Standard was approved by CEN on 2 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1380:2009: ESIST EN 1380:2009

3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 deformation of the connection mean value of the measurements of the relative displacements of the members 3.2 dowel type fasteners elements such as nails, screws, dowels and bolts as defined by EN 14592 4 Symbols and abbreviations For the purposes of this document, the following symbols and abbreviations apply. b
width of member cross-section, in millimetres F load, in newtons t member thickness, in millimetres 5 Requirements 5.1 Timber The timber (solid timber or glued laminated timber) shall satisfy the requirements of EN 14080, EN 14081-1 and shall be selected in accordance with either of the methods given in EN 28970. For each test piece, the individual members to be joined shall be selected to ensure a test piece of balanced density. For a group of similar test pieces, separate planks shall be used for each test piece. NOTE The members should be free from major defects, which could lead to premature failure in the area away from the fasteners. 5.2 Wood-based products The specification of the wood based products shall be established.
...