CEN/TC 124/WG 1 - Test methods

This document specifies test methods for the determination of natural frequencies, damping, unit point load deflection and acceleration of floors composed of sawn timber, engineered wood products, and mass timber beams or slabs (e.g. cross laminated timber CLT, glued laminated timber GL, nail laminated timber), with or without concrete screeds, as well as for timber-concrete composite floors.

This European Standard specifies a test method for the determination of the long duration withdrawal strength of coated and uncoated dowel-type fasteners in structural timber and timber products and wood based products for structural application.
The method applies to all types of nails, screws and staples.

This European Standard specifies the test method for determining the withdrawal capacity of fasteners which have been inserted into timber (solid timber, LVL, CLT and glued laminated timber).
The test method applies to all types of nails, screws and staples.

This European Standard specifies test methods for determining the strength and deformation characteristics of stapled joints in load-bearing timber structures.
The methods assess joints with members of timber (solid timber and glued laminated timber) or wood-based products in the combination proposed for use in service and using all types of staples up to 3 mm diameter for circular cross-section staples or 4 mm x 2 mm for rectangular or oval cross-section staples.
The methods determine load-slip characteristics and maximum load of joints with laterally loaded staples where various angles between the applied force and the timber grain direction or the main direction of the wood-based products, respectively, are possible.

This European Standard specifies the test method for determining the resistance of timber to the head pull through of timber fasteners.
In this standard 'timber' includes solid timber, glued laminated timber and wood-based products.
The test method applies to all types of nails, screws and staples excluding screws with fully threaded shank.

This European Standard specifies the test methods for determining the strength capacity and stiffness of joints made with punched metal plate fasteners in load bearing timber structures, being used to join two or more pieces of timber of the same thickness in the same plane. The properties measured are:
-   load-slip characteristics and maximum load resulting from the lateral resistance of the embedded projections, at various angles between the direction of the applied force and;
-   the axis of the fastener (load-fastener angle );
-   the direction of the grain of the timber (load-grain angle β);
-   the tension capacity of the fastener at various angles ;
-   the compression capacity of the fastener at various angles ;
-   the shear capacity of the fastener at various angles ..
A nail root test method is shown in Annex A.

This European Standard specifies test methods for determining the following properties of structural timber and glued laminated timber: modulus of elasticity in bending; shear modulus; bending strength; modulus of elasticity in tension parallel to the grain; tension strength parallel to the grain; modulus of elasticity in compression parallel to the grain; compression strength parallel to the grain; modulus of elasticity in tension perpendicular to the grain; tension strength perpendicular to the grain; modulus of elasticity in compression perpendicular to the grain; compression strength perpendicular to the grain and shear strength.
In addition, the determination of dimensions, moisture content, and density of test pieces are specified.
The methods apply to rectangular and circular shapes (of substantially constant cross section) of solid unjointed timber or finger-jointed timber and glued laminated timber unless stated otherwise.

This European Standard specifies the test method to be used in determining the racking strength and stiffness of timber frame wall panels.
The test method is intended primarily for panels as described, to provide:
- comparative performance values for the materials used in the manufacture of the panels, and
- data information for use in structural design.
The principle of the test method is suited to other sizes and shapes of panels and to other methods of hold down as well as panels which are partially sheathed and to combinations of panels.
NOTE   The method is detailed for a general situation where the client for the test knows the materials to be used in the construction, which may cover a range of different panels and walls and therefore wishes to test a standard configuration of panel. Where specific details are fixed they may be incorporated into the test but any additions or changes to the standard configuration are indicated in the test report and, later, can lead to limitations on the use of the test data.

This standard specifies a test method to determine the torsional resistance to driving of screws in solid timber or glued laminated timber or other wood based materials.

This European Standard specifies a test method to determine the withdrawal behaviour of punched metal plate fasteners.

This European Standard specifies a method for determining the yield moment of dowel type fasteners.

This European Standard specifies test methods for determining the strength and deformation characteristics of laterally loaded connections with nail, screws, dowels and bolts in load-bearing timber structures.
The methods assess connections with members of timber (solid timber or glued laminated timber) or wood-based products or metal plates (but not punched metal plate fasteners) in the combination proposed for use in service.
The methods are used to determine load-slip characteristics and maximum load of connections where various angles between the applied force and the timber grain direction, or the main direction of the wood-based products, respectively, are possible.

This standard specifies laboratory methods to determine the embedding strength and foundation values of solid timber, glued laminated timber and wood based sheet products with dowel type fasteners.

UAP of 3 months applies.
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)

This standard specifies test methods for determining some mechanical properties of commercial wood-based panel products for use in load-bearing timber structures. These properties are intended for the calculation of characteristic values for use in obtaining material design values. For each type and grade of panel product, as defined for example in an EN wood based panel standard, it is necessary to determine characteristic values of mechanical properties to enable it to be used for structural purposes.

This standard applies for structural round wood timber other than specified in EN 12509.
This test standard specifies test methods for determining the following properties of structural round timber; the bending strength, modulus of elasticity in bending; the compressive strength parallel to the grain and modulus of elasticity in compression parallel to the grain.
In addition, the determination of dimensions, moisture content and density is specified. The methods apply to debarked round timber.
This standard is not intended for quality-control test purposes.

This European Standard specifies a test method for determining the ductility, impairment of strength and energy dissipation properties of joints made with mechanical fasteners under cyclic loading.
NOTE   This standard is written, for uniformity, in terms of direct axial loads and their effects only. The standard is, however, also appropriate to the determination of the moment resisting properties of joints.

This standard specifies test methods for determining the performance of structural floor decking subjected to: - specified concentrated static load (due e.g. to imposed action from persons, furniture and equipment) and - specified impact load (produced e.g. by human motion). The decking considered is constructed of boards, laminated boards or wood based panel products supported on timber joists.

This standard specifies a test method for determining the resistance of a timberframe wall panel to impact from a soft body allowed to strike the sheathing of the panel.

This standard specifies the test procedures for determining the strength and deformation behaviour of trusses. Note: The tests are based on EN 380.

This standard specifies the general principles to be adopted for static load testing of timber structures or components. It is intended for use where it is necessary to verify by test that a structure or components complies with stated criteria. Relevant parts may be used for proof loading or for the testing of structures in service. This standard is not intended to be used for testing of individual pieces of timber, individual joints or structural scaled models

This European Standard specifies test methods for determining the following properties of structural timber and glued laminated timber: modulus of elasticity in bending; shear modulus; bending strength, modulus of elasticity in tension and tension strength parallel to the grain; modulus of elasticity in compression and compression strength parallel to the grain; modulus of elasticity in tension and tension strength perpendicular to the grain; modulus of elasticity in compression and compression strength perpendicular to the grain; and shear strength.

This European Standard specifies the test method for determining the resistance of timber to the head pull through of timber fasteners. The test method applies to all types of nails, screws and staples.

This standard specifies test methods for determining the strength and deformation characteristics of stapled joints in load-bearing timber structures. The methods assess joints with members of timber (solid timber and glued laminated timber) or wood-based products in the combination proposed for use in service and using all types of staples up to 3 mm diameter for circular cross-section staples or 4 mm x 2 mm for rectangular or oval cross-section staples.

This European Standard specifies the test method for determining the withdrawal capacity of fasteners which have been inserted into timber (solid timber and glued laminated timber). The test method applies to all types of nails, screws and staples.

This European Standard specifies the test methods for determining the strength capacity and stiffness of joints made with punched metal plate fasteners in load bearing timber structures, being used to join two or more pieces of timber of the same thickness in the same plane. The properties measured are: load-slip characteristics and maximum load resulting from th lateral resistance of the embedded projections, at various angles between the direction of the applied force and the axis of the fastener and the direction of the grain of the timber, the tension capacity of the fastener at various angles, the compression...

This standard specifies the test method to be used in determining the racking strength and stiffness of timber frame wall panels. The test method is intended, primarily for panels as described, to provide: - comparative performance values for the materials used in the manufacture of the panels and; - datum information for use in structural design. The principle of the test method is suited to other sizes or shapes of panels and to panels which are partially sheathed and to combinations of panels.

This European Standard specifies test methods for determining the strength and deformation characteristics of laterally loaded nailed joints in load-bearing timber structures. The methods assess joints with members of timber (solid timber or glued laminated timber) or wood based products or metal plates (but not punched metal plate fasteners) in the combination proposed for use in service using all types of nails. The methods are used to determine load-slip characteristics and maximum load of joints where various angles between the applied force and the timber grain direction, or the main direction of the wood based products,...

This Standard specifies a method for determining the yield moment of nails having a maximum diameter of 8 mm. The results may be used to determine the characteristic yield moment of the nails for use in structural design

This standard specifes laboratory methods of determining the embedding strength and foundation values of solid timber, glued laminated timber, and wood based sheet products for with dowel type fasteners.

This standard specifies test methods for determining some mechanical properties of commercial wood-based panel products for use in load-bearing timber structures. These properties are intended for the calculation of characteristic values for use in obtaining material design values. For each type and grade of panel product, as defined for example in an EN wood based panel standard, it is necessary to determine characteristic values of mechanical properties to enable it to be used for structural purposes.

This standard specifies test methods for determining: a) tensile and compressive  strengths perpendicular to the grain of structural timber and glued laminated  timber and b) tensile and compressive moduli of elasticity perpendicular to the  grain of structural timber and glued laminated timber and c) shear strength parallel to the grain of structural timber and of the laminates used in glued laminated timber.

This standard specifies test methods for determining the following properties of structural timber and glued laminated timber: modulus of elasticity in bending; shear modulus; bending strength; modulus of elasticity in tension parallel to the grain; tension strength parallel to the grain; modulus of elasticity in compression parallel to the grain; compression strength parallel to the grain. In addition, the determination of dimensions, moisture content, and density are specified.