EN 14915:2013+A1:2017
(Main)Solid wood panelling and cladding - Characteristics, requirements and marking
Solid wood panelling and cladding - Characteristics, requirements and marking
This European Standard defines and specifies the relevant characteristics and the appropriate test methods to determine these characteristics for solid wood products to be used as panelling and cladding (including siding) for:
- wall and ceiling panelling for internal use,
- wall and ceiling cladding for external uses.
It provides for the assessment and verification of constancy of performance and the requirements for marking these products.
This European Standard does not cover panels intended for use as stiffening elements.
This European Standard does not cover suspended ceiling in wood panelling and cladding.
This European Standard does not cover the processes for treatment, surface coating or modification.
This European standard does not cover products which are produced from laminated layer section.
This European Standard covers treated, untreated and surface coated products, including those made of thermally or chemically modified wood, as well as finger jointed and edge glued products.
NOTE Prescriptions for surface coating and treatment can be found in documents valid in the place of use.
This European Standard covers products in compliance with EN 14519, EN 15146 and EN 14951, and other solid timber products manufactured for use as panelling and cladding.
Wand- und Deckenbekleidungen aus Massivholz - Eigenschaften, Anforderungen und Kennzeichnung
Lambris et bardages en bois - Caractéristiques, exigences et marquage
Notranje in zunanje obloge iz masivnega lesa - Lastnosti, zahteve in označevanje
Ta evropski standard opredeljuje in navaja veljavne značilnosti in primerne preskusne metode za določanje lastnosti izdelkov iz masivnega lesa, ki se uporabljajo za notranje in zunanje obloge:
– stenske in stropne obloge za notranjo uporabo,
– stenske in stropne obloge za zunanjo uporabo.
»Omogoča ocenjevanje in preverjanje nespremenljivosti lastnosti teh izdelkov in podaja zahteve za njihovo označevanje«.
Ta evropski standard ne vključuje plošč, ki se uporabljajo kot ojačitveni elementi.
Ta evropski standard ne vključuje visečih lesenih stropnih opažev.
Ta evropski standard ne vključuje procesov za obdelavo, premazovanje ali spreminjanje površin.
Ta evropski standard ne vključuje izdelkov z laminirano plastjo.
Ta evropski standard vključuje vse obdelane, neobdelane in površinsko premazane izdelke, vključno s tistimi iz toplotno ali kemično obdelanega lesa ter izdelke z zobatimi spoji in robno lepljenimi izdelki.
OPOMBA: Predpise za površinske premaze in obdelavo lahko najdete v dokumentih, veljavnih na mestu uporabe.
Ta evropski standard vključuje izdelke, navedene v standardih EN 14519, EN 15146 in EN 14951, in druge izdelke iz masivnega lesa, proizvedene za stenske in stropne opaže.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Wand- und Deckenbekleidungen aus Massivholz - Eigenschaften, Anforderungen und KennzeichnungLambris et bardages en bois - Caractéristiques, exigences et marquageSolid wood panelling and cladding - Characteristics, requirements and marking79.080Polizdelki iz lesaSemi-manufactures of timberICS:Ta slovenski standard je istoveten z:EN 14915:2013+A1:2017SIST EN 14915:2013+A1:2017en,fr,de01-september-2017SIST EN 14915:2013+A1:2017SLOVENSKI
STANDARDSIST EN 14915:20131DGRPHãþD
SIST EN 14915:2013+A1:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14915:2013+A1
June
t r s y ICS
y {ä r z r Supersedes EN
s v { s wã t r s uEnglish Version
Solid wood panelling and cladding æ Characteristicsá requirements and marking Lambris et bardages en bois æ Caractéristiquesá exigences et marquage
Wandæ und Deckenbekleidungen aus Massivholz æ Eigenschaftená Anforderungen und Kennzeichnung This European Standard was approved by CEN on
z August
t r s u and includes Amendment
s approved by CEN on
s r April
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v { s wã t r s u ªA sã t r s y ESIST EN 14915:2013+A1:2017
EN 14915:2013+A1:2017 (E) 2 Contents
Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 5 4 Durability against biological attack . 5 4.1 Biological durability . 5 4.2 !Wood" treated against biological attack. 6 5 Testing, assessment and sampling methods . 6 5.1 Reaction to fire . 6 5.2 Dangerous substances . 8 5.3 Release of other dangerous substances . 9 5.4 Water vapour permeability . 9 5.5 Sound absorption . 9 5.6 Thermal conductivity . 10 5.7 Resistance to fixing . 10 6 Assessment and verification of constancy of performance - AVCP . 10 6.1 General . 10 6.2 Type testing .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.