EN ISO/IEC 17050-2:2004
(Main)Conformity assessment - Supplier's declaration of conformity - Part 2: Supporting documentation (ISO/IEC 17050-2:2004)
Conformity assessment - Supplier's declaration of conformity - Part 2: Supporting documentation (ISO/IEC 17050-2:2004)
IEC 60567:2011 deals with the techniques for sampling free gases from gas-collecting relays from power transformers. Three methods of sampling free gases are described. The techniques described take account, on the one hand, of the problems peculiar to analyses associated with acceptance testing in the factory, where gas contents of oil are generally very low and, on the other hand, of the problems imposed by monitoring equipment in the field, where transport of samples may be by un-pressurized air freight and where considerable differences in ambient temperature may exist between the plant and the examining laboratory. Since the publication of the previous edition, CIGRE TF.D1.01.15 has made progress in several areas of dissolved gas analysis (DGA). These advances are included in this fourth edition.
Konformitätsbewertung - Konformitätserklärung von Anbeitern - Teil 2: Unterstützende Dokumentation (ISO/IEC 17050-2:2004)
Dieser Teil von ISO/IEC 17050 legt allgemeine Anforderungen für die unterstützende Dokumentation fest, um die in ISO/IEC 17050-1 beschriebene Konformitätserklärung eines Anbieters zu bekräftigen.
Für die Anwendung dieses Teils von ISO/IEC 17050 kann der Gegenstand der Konformitätserklärung ein Produkt, ein Prozess, ein Managementsystem, eine Person oder eine Stelle sein.
Anstelle von "Konformitätserklärung eines Anbieters" kann, wenn es angemessen erscheint, die Benennung "Konformitätserklärung" verwendet werden.
Evaluation de la conformité - Déclaration de conformité du fournisseur - Partie 2: Documentation d'appui (ISO/IEC 17050-2:2004)
La CEI 60567:2011 traite des techniques d'échantillonnage de gaz libres au niveau des relais de protection des transformateurs de puissance. Trois méthodes d'échantillonnage des gaz libres sont décrites. Les techniques décrites tiennent compte, d'une part, des problèmes spéciaux d'analyse liés aux essais de réception en usine, pour lesquels les teneurs en gaz sont généralement très faibles et, d'autre part, des problèmes rencontrés dans la surveillance de l'équipement en service, pour lesquels il se peut que le transport des échantillons se fasse par fret aérien non pressurisé, ou que des différences importantes de températures puissent exister entre le site de prélèvement et le laboratoire d'analyse. Depuis la publication de l'édition précédente, CIGRE TF.D1.01.15 a fait des progrès dans plusieurs domaines de l'analyse AGD. Ces avancées sont incluses dans la quatrième édition.
Z oljem polnjena električna oprema - Vzorčenje plinov in analiziranje prostih in raztopljenih plinov - Napotek
Ta mednarodni standard obravnava tehnike za vzorčenje prostih plinov iz plinskih relejev močnostnih transformatorjev. Opisane so tri metode za vzorčenje prostih plinov. Ta standard ne zajema tehnik za vzorčenje olja iz opreme, polnjene z oljem, kot so močnostni in instrumentni transformatorji, dušilke, skoznjiki, oljni tlačni kabli in oljni kondenzatorji za nihajni krog; opisane so v točki 4.2 standarda IEC 60475:2011. V olju raztopljeni plini se pred analizo ekstrahirajo iz olja. Opisane so tri osnovne metode, prva z ekstrakcijo v vakuumu (Toeplerjeva črpalka in delno razplinjevanje), druga z nadomeščanjem raztopljenih plinov z vpihavanjem nosilnega plina v vzorce olja (odparevanje) in tretja z ločitvijo plinov med vzorcem olja in majhno količino nosilnega plina (plinska faza). Po ekstrakciji s plinsko kromatografijo se plini kvantitativno analizirajo; opisana je analizna metoda. Prosti plini iz plinskih relejev se analizirajo brez predhodne obdelave. Prednostna metoda, s katero se zagotovi zmogljivost opreme za ekstrakcijo plina in analizo, obravnavane kot enoten sistem, je razplinjevanje vzorcev olja, ki so bili pripravljeni v laboratoriju in vsebujejo znane koncentracije plinov (»standardi za plin v olju«), ter kvantitativna analiza ekstrahiranih plinov. Opisani sta metodi za pripravo standardov za plin v olju. Za dnevna preverjanja kalibracije kromatografa je primerno uporabiti standardno mešanico plinov, ki vsebuje znane količine plinskih sestavin v razmerju, podobnem povprečnim razmerjem plinov, ekstrahiranih iz transformatorskih olj. Opisane tehnike na eni strani upoštevajo težave, značilne za analize v zvezi s preskušanjem sprejemljivosti v tovarni, kjer je vsebnost plinov v olju običajno zelo nizka, na drugi pa tudi težave, ki jih nadzorna oprema povzroča na terenu, če se vzorci prevažajo s tovornim letalom, na katerem se tlak ne uravnava, ali se temperaturi prostora obrata in preiskovalnega laboratorija znatno razlikujeta.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60567:2012
01-marec-2012
=ROMHPSROQMHQDHOHNWULþQDRSUHPD9]RUþHQMHSOLQRYLQDQDOL]LUDQMHSURVWLKLQ
UD]WRSOMHQLKSOLQRY1DSRWHN
Oil-filled electrical equipment - Sampling of gases and analysis of free and dissolved
gases - Guidance
Ölgefüllte elektrische Betriebsmittel - Probennahme von Gasen und die Analyse freier
und gelöster Gase - Anleitung
Matériels électriques immergés - Echantillonnage de gaz et analyse des gaz libres et
dissous - Lignes directrices
Ta slovenski standard je istoveten z: EN 60567:2011
ICS:
29.040.10 Izolacijska olja Insulating oils
SIST EN 60567:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60567:2012
---------------------- Page: 2 ----------------------
SIST EN 60567:2012
EUROPEAN STANDARD
EN 60567
NORME EUROPÉENNE
December 2011
EUROPÄISCHE NORM
ICS 29.040 Supersedes EN 60567:2005
English version
Oil-filled electrical equipment -
Sampling of gases and analysis of free and dissolved gases -
Guidance
(IEC 60567:2011)
Matériels électriques immergés - Ölgefüllte elektrische Betriebsmittel –
Echantillonnage de gaz et analyse des Probennahme von Gasen und Analyse
gaz libres et dissous - freier und gelöster Gase – Anleitung
Lignes directrices (IEC 60567:2011)
(CEI 60567:2011)
This European Standard was approved by CENELEC on 2011-11-24. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60567:2011 E
---------------------- Page: 3 ----------------------
SIST EN 60567:2012
EN 60567:2011 - 2 -
Foreword
The text of document 10/849/FDIS, future edition 4 of IEC 60567, prepared by IEC/TC 10 "Fluids for
electrotechnical applications" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60567:2011.
The following dates are fixed:
(dop) 2012-08-24
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2014-11-24
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60567:2005.
EN 60567:2011 includes the following significant technical changes with respect to EN 60567:2005:
Since the publication of EN 60567:2005, CIGRE TF.D1.01.15 has made progress in several areas of
dissolved gas analysis (DGA), notably
a) oil sampling,
b) laboratory analysis and solubility coefficients of gases in non-mineral oils,
c) calibration of the headspace gas extraction method,
d) more sensitive detectors for chromatography,
e) preparation of air-saturated standards and
f) evaluation of gas monitor readings.
These advances are included in EN 60567:2011.
Sampling of oil for DGA from oil-filled equipment has been moved from EN 60567 to EN 60475 as
reflected in the revised title of this standard.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 60567:2011 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
[1] ISO/IEC 17025 NOTE Harmonized as EN ISO/IEC 17025.
[2] ISO 3675 NOTE Harmonized as EN ISO 3675.
---------------------- Page: 4 ----------------------
SIST EN 60567:2012
- 3 - EN 60567:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60296 - Fluids for electrotechnical applications - EN 60296 -
Unused mineral insulating oils for
transformers and switchgear
IEC 60475 2011 Method of sampling insulating liquids EN 60475 2011
IEC 60599 - Mineral oil-impregnated electrical equipment EN 60599 -
in service - Guide to the interpretation of
dissolved and free gases analysis
ISO 5725 Series Accuracy (trueness and precision) of - -
measurement methods and results
ASTM D2780 - Standard Test Method for Solubility of Fixed - -
Gases in Liquids
---------------------- Page: 5 ----------------------
SIST EN 60567:2012
---------------------- Page: 6 ----------------------
SIST EN 60567:2012
IEC 60567
®
Edition 4.0 2011-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Oil-filled electrical equipment – Sampling of gases and analysis of free and
dissolved gases – Guidance
Matériels électriques immergés – Échantillonnage de gaz et analyse des gaz
libres et dissous – Lignes directrices
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX XA
ICS 29.040 ISBN 978-2-88912-768-9
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60567:2012
– 2 – 60567 © IEC:2011
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 9
2 Normative references . 9
3 Sampling of gases from gas-collecting (Buchholz) relays . 10
3.1 General remarks. 10
3.2 Sampling of free gases by syringe . 10
3.2.1 Sampling equipment . 10
3.2.2 Sampling procedure. 11
3.3 Sampling of free gases by displacement of oil . 12
3.4 Sampling of free gases by vacuum . 13
3.5 Sampling of oil from oil filled equipment . 14
4 Labelling of gas samples . 14
5 Sampling, labelling and transferring of oil from oil-filled equipment . 14
5.1 Sampling and labelling of oil . 14
5.2 Transfer of oil for DGA analysis . 14
5.2.1 Transfer from oil syringes . 14
5.2.2 Transfer from ampoules . 15
5.2.3 Transfer from flexible metal bottles . 15
5.2.4 Transfer from glass and rigid metal bottles . 15
6 Preparation of gas-in-oil standards . 15
6.1 General remark . 15
6.2 First method: preparation of a large volume of gas-in-oil standard . 15
6.2.1 Equipment . 15
6.2.2 Procedure . 16
6.2.3 Calculation . 18
6.3 Second method: preparation of gas-in-oil standards in a syringe or a vial . 18
6.3.1 Equipment . 19
6.3.2 Procedure . 20
7 Extraction of gases from oil . 20
7.1 General remarks. 20
7.2 Multi-cycle vacuum extraction using Toepler pump apparatus . 21
7.2.1 Toepler pump extraction apparatus . 21
7.2.2 Extraction procedure . 24
7.3 Vacuum extraction by partial degassing method . 25
7.3.1 General remark . 25
7.3.2 Partial degassing apparatus . 25
7.3.3 Extraction procedure . 26
7.4 Stripping extraction method . 26
7.4.1 Stripping apparatus . 26
7.4.2 Outline of procedure . 29
7.5 Headspace method . 30
7.5.1 Principle of the method . 30
7.5.2 Symbols and abbreviations . 30
7.5.3 Headspace extraction apparatus. 31
7.5.4 Headspace extraction procedure . 35
---------------------- Page: 8 ----------------------
SIST EN 60567:2012
60567 © IEC:2011 – 3 –
7.5.5 Calibration of the headspace extractor . 39
8 Gas analysis by gas-solid chromatography . 41
8.1 General remarks. 41
8.2 Outline of suitable methods using Table 4 . 42
8.3 Apparatus . 42
8.3.1 Gas chromatograph . 42
8.3.2 Columns . 44
8.3.3 Carrier gas . 44
8.3.4 Detectors . 44
8.3.5 Methanator . 44
8.3.6 Cold trap . 44
8.3.7 Integrator and recorder . 44
8.4 Preparation of apparatus . 45
8.5 Analysis . 45
8.6 Calibration of the chromatograph . 45
8.7 Calculations . 46
9 Quality control . 46
9.1 Verification of the entire analytical system . 46
9.2 Limits of detection and quantification . 47
9.3 Repeatability, reproducibility and accuracy . 47
9.3.1 General remark . 47
9.3.2 Repeatability . 48
9.3.3 Reproducibility . 48
9.3.4 Accuracy . 48
10 Report of results . 49
Annex A (informative) Correction for incomplete gas extraction in partial degassing
method by calculation . 51
Annex B (informative) Mercury-free and shake test versions of the standard extraction
methods . 53
Annex C (informative) Preparation of air-saturated standards . 55
Annex D (informative) Correction for gas bubbles in syringes and air gap in rigid
bottles . 56
Annex E (informative) Procedure for comparing gas monitor readings to laboratory
results . 57
Bibliography . 58
Figure 1 – Sampling of gas by syringe . 11
Figure 2 – Sampling of free gases by oil displacement . 12
Figure 3 – Sampling of free gases by vacuum . 13
Figure 4 – First method of preparing gas-in-oil standards . 17
Figure 5 – Second method for preparing gas-in-oil standards . 19
Figure 6 – Example of a Toepler pump extraction apparatus . 23
Figure 7 – Types of glass strippers . 27
Figure 8 – Stainless steel stripper . 28
Figure 9 – Schematic arrangement for connecting an oil stripper to a gas
chromatograph . 29
Figure 10 – Schematic representation of headspace sampler . 30
---------------------- Page: 9 ----------------------
SIST EN 60567:2012
– 4 – 60567 © IEC:2011
Figure 11 – Vial filled with water . 32
Figure 12 – Revolving table . 34
Figure 13 – Schematic arrangement for gas chromatography . 43
Figure B.1 – Schematic representation of methods in Annex B . 54
Table 1 – Information required for gas samples . 14
Table 2 – Examples of headspace operating conditions . 35
Table 3 – Headspace partition coefficients at 70 °C in mineral insulating oil . 40
Table 4 – Examples of gas chromatographic operating conditions . 41
Table 5 – Required limits of detection in oil . 47
Table 6 – Examples of accuracy of extraction methods . 49
Table A.1 – Examples of solubility coefficients a (at 25 ºC) reported by CIGRE TF
i
D1.01.15 . 51
Table C.1 – Examples of solubility values of air for different oil types . 55
Table C.2 – Examples of temperature variations for oxygen and nitrogen solubility in
mineral oil . 55
---------------------- Page: 10 ----------------------
SIST EN 60567:2012
60567 © IEC:2011 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OIL-FILLED ELECTRICAL EQUIPMENT –
SAMPLING OF GASES AND ANALYSIS
OF FREE AND DISSOLVED GASES –
GUIDANCE
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60567 has been prepared by IEC technical committee 10: Fluids
for electrotechnical applications.
This fourth edition cancels and replaces the third edition, published in 2005, and constitutes a
technical revision.
The main changes with respect to the previous edition are listed below:
Since the publication of the third edition, CIGRE TF.D1.01.15 has made progress in several
areas of dissolved gas analysis (DGA), notably
a) oil sampling,
b) laboratory analysis and solubility coefficients of gases in non-mineral oils,
c) calibration of the headspace gas extraction method,
---------------------- Page: 11 ----------------------
SIST EN 60567:2012
– 6 – 60567 © IEC:2011
d) more sensitive detectors for chromatography,
e) preparation of air-saturated standards and
f) evaluation of gas monitor readings.
These advances are included in this fourth edition.
Sampling of oil for DGA from oil-filled equipment has been moved from IEC 60567 to
IEC 60475 as reflected in the revised title of this standard.
The text of this standard is based on the following documents:
FDIS Report on voting
10/849/FDIS 10/872/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 12 ----------------------
SIST EN 60567:2012
60567 © IEC:2011 – 7 –
INTRODUCTION
Gases may be formed in oil-filled electrical equipment due to natural ageing but also, to a
much greater extent, as a result of faults.
Operation with a fault may seriously damage the equipment, and it is valuable to be able to
detect the fault at an early stage of development.
Where a fault is not severe, the gases formed will normally dissolve in the oil, with a small
proportion eventually diffusing from the liquid into any gas phase above it. Extracting
dissolved gas from a sample of the oil and determining the amount and composition of this
gas is a means of detecting such faults, and the type and severity of any fault may often be
inferred from the composition of the gas and the rate at which it is formed.
In the case of a sufficiently severe fault, free gas will pass through the oil and collect in the
gas-collecting (Buchholz) relay if fitted; if necessary, this gas may be analysed to assist in
determining the type of fault that has generated it. The composition of gases within the
bubbles changes as they move through the oil towards the gas-collecting relay.
This can be put to good use, as information on the rate of gas production may often be
inferred by comparing the composition of the free gases collected with the concentrations
remaining dissolved in the liquid.
The interpretation of the gas analyses is the subject of IEC 60599.
These techniques are valuable at all stages in the life of oil-filled equipment. During
acceptance tests on transformers in the factory, comparison of gas-in-oil analyses before,
during and after a heat run test can show if any hot-spots are present, and similarly analysis
after dielectric testing can add to information regarding the presence of partial discharges or
sparking. During operation in the field, the periodic removal of an oil sample and analysis of
the gas content serve to monitor the condition of transformers and other oil-filled equipment.
The importance of these techniques has led to the preparation of this standard, to the
procedures to be used for the sampling, from oil-filled electrical equipment, of gases and oils
containing gases, and for subsequent analysis.
NOTE Methods described in this standard apply to insulating oils, since experience to date has been almost
entirely with such oils. The methods may also be applied to other insulating liquids, in some cases with
modifications.
General caution, health, safety and environmental protection
This International Standard does not purport to address all the safety problems associated
with its use. It is the responsibility of the user of the standard to establish appropriate health
and safety practices and determine the applicability of regulatory limitations prior to use.
The insulating oils which are the subject of this standard should be handled with due regard to
personal hygiene. Direct contact with the eyes may cause irritation. In the case of eye
contact, irrigation with copious quantities of clean running water should be carried out and
medical advice sought. Some of the tests specified in this standard involve the use of
processes that could lead to a hazardous situation. Attention is drawn to the relevant standard
for guidance.
Mercury presents an environmental and health hazard. Any spillage should immediately be
removed and be properly disposed of. Consult local regulations for mercury use and handling.
Mercury-free methods may be requested in some countries.
---------------------- Page: 13 ----------------------
SIST EN 60567:2012
– 8 – 60567 © IEC:2011
Environment
This standard is applicable to insulating oils, chemicals and used sample containers.
Attention is drawn to the fact that, at the time of writing of this standard, many insulating oils
in service are known to be contaminated to some degree by PCBs. If this is the case, safety
countermeasures should be taken to avoid risks to workers, the public and the environment
during the life of the equipment, by strictly controlling spills and emissions. Disposal or
decontamination of these oils should be carried out strictly according to local regulations.
Every precaution should be taken to prevent release of insulating oil into the environment.
---------------------- Page: 14 ----------------------
SIST EN 60567:2012
60567 © IEC:2011 – 9 –
OIL-FILLED ELECTRICAL EQUIPMENT –
SAMPLING OF GASES AND ANALYSIS
OF FREE AND DISSOLVED GASES –
GUIDANCE
1 Scope
This International Standard deals with the techniques for sampling free gases from gas-
collecting relays from power transformers. Three methods of sampling free gases are
described.
The techniques for sampling oil from oil-filled equipment such as power and instrument
transformers, reactors, bushings, oil-filled cables and oil-filled tank-type capacitors are no
longer covered by this standard, but are instead described in 4.2 of IEC 60475:2011
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.