EN 61000-6-3:2007

Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments

This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in residential, commercial and light-industrial environments. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or product-family EMC emission standard exists. This standard applies to apparatus intended to be directly connected to a low-voltage public mains network or connected to a dedicated DC source, which is intended to interface between the apparatus and the low-voltage public mains network. This standard applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, low-voltage power distribution system if this apparatus is intended to be used in the locations described below. The environments encompassed by this standard are residential, commercial and light-industrial locations, both indoor and outdoor. The following list, although not comprehensive, gives an indication of locations that are included: - residential properties, for example houses, apartments; - retail outlets, for example shops, supermarkets; - business premises, for example offices, banks; - areas of public entertainment, for example cinemas, public bars, dance halls; - outdoor locations, for example petrol stations, car parks, amusement and sports centres; - light-industrial locations, for example workshops, laboratories, service centres. Locations that are characterised by being supplied directly at low voltage from the public mains network are considered to be residential, commercial or light-industrial. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in residential, commercial and light-industrial locations do not exceed a level which could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements. Requirements are specified for each port considered.

Elektromagnetische Verträglichkeit (EMV) - Teil 6-3: Fachgrundnormen - Störaussendung für Wohnbereich, Geschäfts- und Gewerbebereiche sowie Kleinbetriebe

Compatibilité électromagnétique (CEM) - Partie 6-3: Normes génériques - Norme sur l'émission pour les environnements résidentiels, commerciaux et de l'industrie légère

La présente partie de la CEI 61000 concernant les exigences d'émissions en matière de compatibilité électromagnétique s'applique aux appareils électriques et électroniques destinés à être utilisés dans des environnements résidentiels, commerciaux et de l'industrie légère. Les exigences d'émissions dans la gamme de fréquences de 0 kHz à 400 GHz sont couvertes. Il n'est pas nécessaire de réaliser des mesures aux fréquences pour lesquelles aucune exigence n'a été spécifiée. Cette norme d'émission CEM générique s'applique en l'absence de norme applicable d'émission CEM spécifique à un produit ou à une famille de produits. Cette norme s'applique aux appareils destinés à être raccordés directement au réseau public d'alimentation basse tension ou à une source de courant continu spécifique destinée à servir d'interface entre l'appareil et le réseau public d'alimentation basse tension. Cette norme s'applique également aux appareils alimentés par piles ou batteries ou par un système de distribution basse tension non public mais non industriel, lorsque cet appareil est destiné à être utilisé dans les emplacements décrits ci-dessous. Les environnements couverts par cette norme sont les sites résidentiels, les locaux commerciaux et de l'industrie légère, à la fois intérieurs et extérieurs. La liste suivante, bien que non exhaustive, donne une indication sur les sites qui sont couverts: - propriétés résidentielles, par exemple maisons, appartements ; - lieux de vente au détail, par exemple boutiques, supermarchés; - centres d'affaires, par exemple bureaux, banques; - locaux de loisirs recevant du public, par exemple cinémas, bars, dancings; - sites extérieurs, par exemple stations service, parcs de stationnement, centres de loisirs et centres sportifs; - locaux de l'industrie légère, par exemple ateliers, laboratoires, centres de services. Les sites qui sont caractérisés comme étant alimentés directement en basse tension par le réseau public sont considérés comme résidentiels, commerciaux ou pour l'industrie légère. L'objet de cette norme est de définir les exigences d'essais d'émissions aux perturbations continues et transitoires, conduites et rayonnées, pour les appareils définis dans le domaine d'application. Les exigences des perturbations émises ont été choisies de manière à assurer que les perturbations engendrées par l'appareil en fonctionnement normal, dans un environnement résidentiel, commercial ou de l'industrie légère, ne dépassent pas un niveau qui pourrait empêcher d'autres appareils de fonctionner comme prévu normalement. Les conditions de défaut de l'appareil ne sont pas prises en compte. Cette norme ne comporte pas, pour les besoins des essais, tous les phénomènes perturbateurs mais uniquement ceux considérés comme applicables pour les appareils couverts par la norme. Ces exigences représentent les exigences essentielles de compatibilité électromagnétique concernant les émissions. Les exigences sont spécifiées pour chacun des accès considérés.

Elektromagnetna združljivost (EMC) - 6-3. del: Osnovni standardi - Standard oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih industrijskih okoljih (IEC 61000-6-3:2006)

Ta del standarda IEC 61000 za zahteve glede oddajanja motenj v zvezi z elektromagnetno združljivostjo se uporablja za električne in elektronske naprave, ki so namenjene za uporabo v stanovanjskih, poslovnih in manj zahtevnih industrijskih okoljih. Zajema zahteve glede oddajanja motenj v frekvenčnem razponu od 0 Hz do 400 GHz. Za frekvence, za katere ni določenih zahtev, ni treba opraviti meritev. Ta generični standard oddajanja motenj v zvezi z elektromagnetno združljivostjo se uporablja, če ne obstaja ustrezen poseben standard oddajanja motenj v zvezi z elektromagnetno združljivostjo izdelka ali družine izdelkov. Ta standard se uporablja za naprave, ki so namenjene za neposredno povezavo z glavnim javnim nizkonapetostnim omrežjem ali povezavo s posebnim virom enosmernega toka, ki je namenjen povezavi med napravo in glavnim javnim nizkonapetostnim omrežjem. Ta standard se uporablja tudi za naprave, ki delujejo na baterije ali se napajajo iz zasebnega, vendar ne industrijskega, nizkonapetostnega sistema za distribucijo energije, če je naprava namenjena za uporabo na spodaj navedenih lokacijah. Ta standard zajema stanovanjske, poslovne in manj zahtevne industrijske lokacije, in sicer znotraj in na prostem. Na naslednjem seznamu so navedene nekatere od zajetih lokacij: – stanovanjski objekti, na primer hiše in stanovanja, – maloprodajna mesta, na primer trgovine in supermarketi, – poslovni objekti, na primer pisarne in banke, – javne zabaviščne površine, na primer kinodvorane, javni lokali in plesišča, – lokacije na prostem, na primer bencinski servisi, parkirišča ter zabaviščni in športni centri, – manj zahtevna industrijska okolja, na primer delavnice, laboratoriji in storitvena središča. Lokacije, ki se napajajo neposredno z nizko napetostjo iz glavnega javnega omrežja, se štejejo za stanovanjska, poslovna ali manj zahtevna industrijska okolja. Cilj tega standarda je opredeliti zahteve za preskus oddajanja motenj za naprave, ki so opredeljene za to področje uporabe, v zvezi s trajnimi in prehodnimi motnjami ter motnjami sevanja. Zahteve glede oddajanja motenj so izbrane tako, da zagotavljajo, da motnje, ki jih proizvedejo naprave pri normalnem delovanju v stanovanjskih, poslovnih in manj zahtevnih industrijskih okoljih, ne presežejo ravni, ki bi lahko drugim napravam preprečila delovanje, za katerega so namenjene. Motnje naprav se ne upoštevajo. Ta standard ne zajema vseh motenj za namene preskušanja, ampak le motnje, ki so pomembne za opremo, zajeto v tem standardu. Te zahteve predstavljajo osnovne zahteve glede oddajanja motenj v zvezi z elektromagnetno združljivostjo.

General Information

• Status: Withdrawn
• Publication Date: 11-Jan-2007
• Withdrawal Date: 30-Nov-2009
• ICS: 33.100 - Electromagnetic compatibility (EMC)
• ICS: 33.100.10 - Emission
• Technical Committee: CLC/TC 210 - Electromagnetic Compatibility (EMC)
• Drafting Committee: IEC/SC CISPR/H - IEC_SC_CISPR/H
• Parallel Committee: IEC/SC CISPR/H - IEC_SC_CISPR/H
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 26-Mar-2024
• Completion Date: 26-Mar-2024
• Directive: 1999/5/EC - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity
• Directive: 2004/108/EC - Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
• Directive: 2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
• Directive: 2014/30/EU - Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast)
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Directive: 89/336/EEC - Electromagnetic compatibility (EMC)
• Mandate: M/404 - Standardisation Mandate to CEN, CENELEC and ETSI for harmonized standard according to the Electro Magnetic Compatibility (EMC) Directive 2004/108/EC
• Mandate: M/490 - Standardisation mandate to the European Standardisation Organisations (ESOs) to support European Smart Grid deployment
• Mandate: M/536 - [C(2015)536] Standardisation request as regards radio equipment in support of Directive 2014/53/EU
• Mandate: M/552 - [C(2016) 7641 final] Standardisation request as regards harmonised standards in support of Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility
• Ref Project: SIST EN 61000-6-3:2007 - Electromagnetic compatibility (EMC) -- Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments

Relations

• Replaces: EN 61000-6-3:2001/A11:2004 - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
• Effective Date: 28-Jan-2023
• Replaces: EN 61000-6-3:2001 - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
• Effective Date: 28-Jan-2023
• Replaced By: EN IEC 61000-6-3:2021 - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for equipment in residential environments
• Effective Date: 11-Dec-2018
• Amended By: EN 61000-6-3:2007/A1:2011 - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2007
1DGRPHãþD
SIST EN 61000-6-3:2002
SIST EN 61000-6-3:2002/A11:2005
Elektromagnetna združljivost (EMC) - 6-3. del: Osnovni standardi - Standard
oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih industrijskih
okoljih (IEC 61000-6-3:2006)
Electromagnetic compatibility (EMC) -- Part 6-3: Generic standards - Emission standard
for residential, commercial and light-industrial environments
Elektromagnetische Verträglichkeit (EMV) - Teil 6-3: Fachgrundnormen -
Störaussendung für Wohnbereich, Geschäfts- und Gewerbebereiche sowie Kleinbetriebe
Compatibilité électromagnétique (CEM) -- Partie 6-3: Normes génériques - Norme sur
l'émission pour les environnements résidentiels, commerciaux et de l'industrie légere
Ta slovenski standard je istoveten z: EN 61000-6-3:2007
ICS:
33.100.10 Emisija Emission
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61000-6-3
NORME EUROPÉENNE
January 2007
EUROPÄISCHE NORM
ICS 33.100.10 Supersedes EN 61000-6-3:2001 + A11:2004

English version
Electromagnetic compatibility (EMC) -
Part 6-3: Generic standards -
Emission standard for residential, commercial
and light-industrial environments
(IEC 61000-6-3:2006)
Compatibilité électromagnétique (CEM) - Elektromagnetische Verträglichkeit
Partie 6-3: Normes génériques - (EMV) -
Norme sur l'émission Teil 6-3: Fachgrundnormen -
pour les environnements résidentiels, Störaussendung für Wohnbereich,
commerciaux et de l'industrie légère Geschäfts- und Gewerbebereiche
(CEI 61000-6-3:2006) sowie Kleinbetriebe
(IEC 61000-6-3:2006)
This European Standard was approved by CENELEC on 2006-12-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61000-6-3:2007 E
Foreword
The text of document CISPR/H/121/FDIS, future edition 2 of IEC 61000-6-3, prepared by CISPR SC H,
Limits for the protection of radio services, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 61000-6-3 on 2006-12-01.
This European Standard supersedes EN 61000-6-3:2001 + A11:2004.
The major changes in EN 61000-6-3:2007 are the inclusion of a clause on tests for equipment in series
production, a new clause on measurement uncertainty and the inclusion of requirements on dc power
ports and telecommunications ports. The informative annex has been deleted.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2009-12-01
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and covers essential requirements of
EC Directives EMC (89/336/EEC), EMC (2004/108/EC) and RTTED (1999/5/EC). See Annex ZZ.
Annexes ZA and ZZ have been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61000-6-3:2006 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61000-6-1 NOTE  Harmonized as EN 61000-6-1:2007 (not modified).
IEC 61000-6-4 NOTE  Harmonized as EN 61000-6-4:2007 (not modified).
__________
- 3 - EN 61000-6-3:2007
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

1) 2)
IEC 61000-3-2 - Electromagnetic compatibility (EMC) - EN 61000-3-2 2006
Part 3-2: Limits - Limits for harmonic current
emissions (equipment input current ≤ 16 A
per phase)
1) 2)
IEC 61000-3-3 - Electromagnetic compatibility (EMC) - EN 61000-3-3 1995
Part 3-3: Limits - Limitation of voltage + corr. July 1997
changes, voltage fluctuations and flicker in
public low-voltage supply systems, for
equipment with rated current ≤ 16 A per
phase and not subject to conditional
connection
1) 2)
IEC 61000-3-11 - Electromagnetic compatibility (EMC) - EN 61000-3-11 2000
Part 3-11: Limits - Limitation of voltage
changes, voltage fluctuations and flicker in
public low-voltage supply systems -
Equipment with rated current ≤ 75 A and
subject to conditional connection

1) 2)
IEC 61000-3-12 - Electromagnetic compatibility (EMC) - EN 61000-3-12 2005
Part 3-12: Limits - Limits for harmonic
currents produced by equipment connected to
public low-voltage systems with input current
> 16 A and ≤ 75 A per phase
1) 2)
CISPR 14-1 - Electromagnetic compatibility - Requirements EN 55014-1 2006
for household appliances, electric tools and
similar apparatus -
Part 1: Emission
CISPR 16-1-2 2003 Specification for radio disturbance and EN 55016-1-2 2004
immunity measuring apparatus and methods -
Part 1-2: Radio disturbance and immunity
measuring apparatus - Ancillary equipment -
Conducted disturbances
CISPR 16-2-1 2003 Specification for radio disturbance and EN 55016-2-1 2004
immunity measuring apparatus and methods -
Part 2-1: Methods of measurement of
disturbances and immunity - Conducted
disturbance measurements
1)
Undated reference.
2)
Valid edition at date of issue.

Publication Year Title EN/HD Year
1) 2)
CISPR 16-2-3 - Specification for radio disturbance and EN 55016-2-3 2006
immunity measuring apparatus and methods -
Part 2-3: Methods of measurement of
disturbances and immunity - Radiated
disturbance measurements
1) 2)
CISPR 16-4-2 - Specification for radio disturbance and EN 55016-4-2 2004
immunity measuring apparatus and methods -
Part 4-2: Uncertainties, statistics and limit
modelling - Uncertainty in EMC
measurements
1) 2)
CISPR 22 - Information technology equipment - Radio EN 55022 2006
disturbance characteristics - Limits and
methods of measurement
- 5 - EN 61000-6-3:2007
Annex ZZ
(informative)
Coverage of Essential Requirements of EC Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers the
essential requirements as given in Article 4(a) of the EC Directive 89/336/EEC and Annex I Article 1(a) of
the EC Directive 2004/108/EC, and the essential requirements of Article 3.1(b) (emission only) of the
EC Directive 1999/5/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.
__________
INTERNATIONAL
IEC
ELECTROTECHNICAL
61000-6-3
COMMISSION
Second edition
2006-07
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
Electromagnetic compatibility (EMC) –
Part 6-3:
Generic standards –
Emission standard for residential, commercial
and light-industrial environments

© IEC 2006 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale N
International Electrotechnical Commission
Международная Электротехническая Комиссия
For price, see current catalogue

61000-6-3  IEC:2006 – 3 –
CONTENTS
FOREWORD.5
INTRODUCTION.9

1 Scope and object.11
2 Normative references .13
3 Terms and definitions .15
4 Conditions during testing .17
5 Product documentation.17
6 Applicability.19
7 Emission requirements .19
8 Application of limits in tests for conformity of equipment in series production .19
9 Measurement uncertainty .21

Bibliography.27

Figure 1 – Examples of ports .15

Table 1 − Emission .23

61000-6-3  IEC:2006 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
___________
ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 6-3: Generic standards –
Emission standard for residential,
commercial and light-industrial environments

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61000-6-3 has been prepared by CISPR subcommittee H: Limits
for the protection of radio services.
This second edition cancels and replaces the first edition published in 1996 as
CISPR/IEC 61000-6-3. It constitutes a technical revision. The major changes in this edition
are the inclusion of a clause on tests for equipment in series production, a new clause on
measurement uncertainty and the inclusion of requirements on dc power ports and
telecommunications ports. The informative annex has been deleted.

61000-6-3  IEC:2006 – 7 –
The text of this standard is based on the following documents:
FDIS Report on voting
CISPR/H/121/FDIS CISPR/H/124/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
61000-6-3  IEC:2006 – 9 –
INTRODUCTION
IEC 61000 is published in separate parts according to the following structure:
Part 1: General
General considerations (introduction, fundamental principles)
Definitions, terminology
Part 2: Environment
Description of the environment
Classification of the environment
Compatibility levels
Part 3: Limits
Emission limits
Immunity limits (insofar as they do not fall under the responsibility of the product
committees)
Part 4: Testing and measurement techniques
Measurement techniques
Testing techniques
Part 5: Installation and mitigation guidelines
Installation guidelines
Mitigation methods and devices
Part 6: Generic standards
Part 9: Miscellaneous
Each part is further subdivided into several parts published either as International Standards
or technical reports/specifications, some of which have already been published as sections.
Others will be published with the part number followed by a dash and a second number
identifying the subdivision (example: 61000-6-1).
...

SLOVENSKI SIST EN 61000-6-3
STANDARD
september 2007
Elektromagnetna združljivost (EMC) – 6-3. del: Osnovni standardi –
Standard oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih
industrijskih okoljih (IEC 61000-6-3:2006)
Electromagnetic compatibility (EMC) – Part 6-3: Generic standards –
Emission standard for residential, commercial and light-industrial environments
(IEC 61000-6-3:2006)
Compatibilité électromagnétique (CEM) – Partie 6-3: Normes génériques –
Norme sur l'émission pour les environnements résidentiels, commerciaux et de
l'industrie légère (CEI 61000-6-3:2006)

Elektromagnetische Verträglichkeit (EMV) – Teil 6-3: Fachgrundnormen –
Störaussendung für Wohnbereich, Geschäfts- und Gewerbebereiche sowie
Kleinbetriebe (IEC 61000-6-3:2006)

Referenčna oznaka
ICS 33.100.10 SIST EN 61000-6-3:2007 (sl)

Nadaljevanje na straneh II in III ter od 1 do 17

© 2016-05. Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN 61000-6-3 : 2007
NACIONALNI UVOD
Standard SIST EN 61000-6-3 (sl), Elektromagnetna združljivost (EMC) – 6-3. del: Osnovni standardi –
Standard oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih industrijskih okoljih (IEC
61000-6-3:2006), 2007, ima status slovenskega standarda in je istoveten evropskemu standardu EN
61000-6-3 (en), Electromagnetic compatibility (EMC) – Part 6-3: Generic standards – Emission
standard for residential, commercial and light-industrial environments (IEC 61000-6-3:2006), 2007.

Ta standard nadomešča SIST EN 61000-6-3:2002.

NACIONALNI PREDGOVOR
Evropski standard EN 61000-6-3:2007 je pripravil tehnični odbor CLC/TC 210 Elektromagnetna
združljivost (EMC). Slovenski standard SIST EN 61000-6-3:2007 je prevod evropskega standarda EN
61000-6-3:2007. V primeru spora glede besedila slovenskega prevoda v tem standardu je odločilen
izvirni evropski standard v angleškem jeziku. Slovensko izdajo standarda je potrdil tehnični odbor
SIST/TC EMC Elektromagnetna združljivost.

Odločitev za privzem tega standarda je v septembru 2007 sprejel tehnični odbor SIST/TC EMC
Elektromagnetna združljivost.
ZVEZA Z NACIONALNIMI STANDARDI

S privzemom tega evropskega standarda veljajo za omejeni namen referenčnih standardov vsi
standardi, navedeni v izvirniku, razen tistih, ki so že sprejeti v nacionalno standardizacijo:
SIST EN 61000-3-2 Elektromagnetna združljivost (EMC) – 3-2. del: Mejne vrednosti – Mejne
vrednosti za oddajanje harmonskih tokov (vhodni tok opreme do vključno
16 A na fazo)
SIST EN 61000-3-3 Elektromagnetna združljivost (EMC) – 3-3. del: Mejne vrednosti –
Omejitev vrednosti kolebanja napetosti in flikerja v nizkonapetostnih
napajalnih sistemih za opremo z naznačenim tokom do 16 A in ni
priključena pod posebnimi pogoji
SIST EN 61000-3-11 Elektromagnetna združljivost (EMC) – 11. del: Mejne vrednosti – Mejne
vrednosti napetostnih sprememb, kolebanja napetosti in flikerja v javnih
nizkonapetostnih napajalnih sistemih – Oprema z naznačenim tokom do
vključno 75 A, ki je predmet pogojnega priklopa
SIST EN 61000-3-12 Elektromagnetna združljivost (EMC) – 3-12. del: Mejne vrednosti – Mejne
vrednosti za harmonske tokove, ki jih povzroča oprema, priključena na
nizkonapetostne napajalne sisteme z naznačenim tokom, večjim od 16 A
in ≤ 75 A po liniji
SIST EN 55014-1 Elektromagnetna združljivost – Zahteve za (električne) gospodinjske
aparate, električna ročna orodja in podobne aparate – 1. del: Oddajanje
SIST EN 55016-1-2:2005 Specifikacija za merilne naprave in metode za merjenje radijskih motenj
in odpornosti – 1-2. del: Merilne naprave za merjenje radijskih motenj in
odpornosti – Pomožna oprema – Motnje po vodnikih (CISPR 16-1-
2:2003)
SIST EN 55016-2-1:2005 Specifikacija za merilne naprave in metode za merjenje radijskih motenj
in odpornosti – 2-1. del: Metode za merjenje radijskih motenj in
odpornosti – Merjenje motenj po vodnikih (CISPR 16-2-1:2003)
SIST EN 55016-2-3 Specifikacija merilnih naprav in metod za merjenje radijskih motenj in
odpornosti – 2-3. del: Metode za merjenje radijskih motenj in odpornosti –
Merjenje sevanih motenj
II
SIST EN 61000-6-3 : 2007
SIST EN 55016-4-2 Specifikacija za merilne naprave in metode za merjenje radijskih motenj
in odpornosti – 4-2. del: Modeliranje negotovosti, statistike in mejnih
vrednosti - Negotovost merilnih instrumentov
SIST EN 55022 Oprema za informacijsko tehnologijo – Karakteristike občutljivosti za
radijske motnje – Mejne vrednosti in merilne metode

OSNOVA ZA IZDAJO STANDARDA
– privzem standarda EN 61000-6-3:2007

PREDHODNA IZDAJA
– SIST EN 61000-6-3:2002, Elektromagnetna združljivost (EMC) – 6-3. del: Osnovni standardi –
Standard oddajanja motenj v stanovanjskih, poslovnih in lahkoindustrijskih okoljih

OPOMBE
– Povsod, kjer se v besedilu standarda uporablja izraz "evropski" ali "mednarodni" standard, v SIST
– Nacionalni uvod in nacionalni predgovor nista sestavni del standarda.
– Ta nacionalni dokument je istoveten EN 61000-6-3:2007 in je objavljen z dovoljenjem

CEN/CENELEC
Upravni center
Avenue Marnix 17
B-1000 Bruselj
This national document is identical with EN 61000-6-3:2007 and is published with the permission of

CEN/CENELEC
Management Centre
Avenue Marnix 17
B -1000 Brussels
III
EVROPSKI STANDARD EN 61000-6-3
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM januar 2007
ICS: 33.100.10    Nadomešča EN 61000-6-3:2001+A11:2004

Slovenska izdaja
Elektromagnetna združljivost (EMC) – 6-3. del: Osnovni standardi – Standard
oddajanja motenj v stanovanjskih, poslovnih in manj zahtevnih industrijskih
okoljih (IEC 61000-6-3:2006)
Electromagnetic compatibility Compatibilité électromagnétique Elektromagnetische Verträglichkeit
(EMC) – Part 6-3: Generic (CEM) – Partie 6-3: Normes (EMV) – Teil 6-3: Fachgrundnormen
standards – Emission standard génériques – Norme sur l'émission – Störaussendung für Wohnbereich,
for residential, commercial and pour les environnements Geschäfts- und Gewerbebereiche
light-industrial environments résidentiels, commerciaux et de sowie Kleinbetriebe (IEC 61000-6-
(IEC 61000-6-3:2006) l'industrie légère (CEi 61000-6- 3:2006)
3:2006)
Ta evropski standard je CENELEC sprejel 1. decembra 2006. Člani CENELEC morajo izpolnjevati
notranje predpise CEN/CENELEC, s katerimi so predpisani pogoji za privzem tega evropskega
standarda na nacionalno raven brez kakršnihkoli sprememb.

Najnovejši seznami teh nacionalnih standardov z njihovimi bibliografskimi podatki se na zahtevo lahko
dobijo pri Centralnem sekretariatu ali kateremkoli članu CENELEC.

Ta evropski standard obstaja v treh uradnih izdajah (angleški, francoski in nemški). Izdaje v drugih
jezikih, ki jih člani CENELEC na lastno odgovornost prevedejo in izdajo ter prijavijo pri Centralnem
sekretariatu, veljajo kot uradne izdaje.

Člani CENELEC so nacionalni elektrotehniški komiteji Avstrije, Belgije, Bolgarije, Cipra, Češke
republike, Danske, Estonije, Finske, Francije, Grčije, Islandije, Irske, Italije, Latvije, Litve,
Luksemburga, Madžarske, Malte, Nemčije, Nizozemske, Norveške, Poljske, Portugalske, Romunije,
Slovaške, Slovenije, Španije, Švedske, Švice in Združenega kraljestva.

CENELEC
Evropski komite za standardizacijo v elektrotehniki
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Centralni sekretariat: Rue de Stassart 35, B-1050 Bruselj

© 2007 CENELEC Lastnice avtorskih pravic so vse države članice CENELEC. Ref. št. EN 61000-6-3:2007 E

SIST EN 61000-6-3 : 2007
VSEBINA Stran
Predgovor k evropskemu standardu . 3
Dodatek ZA (normativni): Sklicevanje na mednarodne publikacije z njihovimi ustreznimi
evropskimi publikacijami . 4
Dodatek ZZ (informativni): Vključitev bistvenih zahtev direktiv ES . 6
Predgovor k mednarodnemu standardu . 7
Uvod . 9
1 Področje uporabe in namen . 10
2 Zveze s standardi . 11
3 Izrazi in definicije . 11
4 Pogoji med preskušanjem . 13
5 Dokumentacija o proizvodu . 13
6 Uporabnost . 13
7 Zahteve za oddajanje motenj . 13
8 Uporaba mejnih vrednosti in preskusov za skladnost opreme v serijski proizvodnji . 14
9 Merilna negotovost . 14
Literatura. 17

Preglednica 1: Oddajanje motenj . 15

Slika 1: Prrimeri portov . 12

SIST EN 61000-6-3 : 2007
Predgovor k evropskemu standardu

Besedilo dokumenta CISPR/H/121/FDIS, prihodnje 2. izdaje IEC 61000-6-3, ki ga je pripravil
pododbor CISPR SC H Meje za zaščito radijskih storitev, je CENELEC po vzporednem glasovanju v
IEC in CENELEC 1. decembra 2006 sprejel kot EN 61000-6-3.

Ta evropski standard nadomešča EN 61000-6-3:2001+A11:2004.

Glavne spremembe v EN 61000-6-3:2007 so dodana točka o preskusih opreme v serijski proizvodnji,
nova točka o merilni negotovosti ter dodane zahteve za enosmerne napajalne in telekomunikacijske
porte. Izbrisan je bil informativni dodatek.

Določena sta bila naslednja datuma:
– zadnji datum, do katerega mora EN dobiti status
nacionalnega standarda bodisi z objavo istovetnega besedila
ali z razglasitvijo (dop) 2007-09-01
– zadnji datum, ko je treba razveljaviti nacionalne standarde,
ki so z EN v nasprotju (dow) 2009-12-01
Dodatka ZA in ZZ je dodal CENELEC.

Razglasitvena objava
Besedilo mednarodnega standarda IEC 61000-6-3:2006 je CENELEC odobril kot evropski standard
brez kakršnihkoli sprememb.
V uradni verziji je treba v Literaturi dodati opombo k naslednjima standardoma:

IEC 61000-6-1 OPOMBA Harmoniziran kot EN 61000-6-1:2007 (nespremenjen)
IEC 61000-6-4 OPOMBA Harmoniziran kot EN 61000-6-4 (nespremenjen)

SIST EN 61000-6-3 : 2007
Dodatek ZA
(normativni)
Sklicevanje na mednarodne publikacije z njihovimi ustreznimi evropskimi
publikacijami
Pri uporabi tega dokumenta so nujno potrebni naslednji referenčni dokumenti. Pri datiranih
sklicevanjih velja le navedena izdaja dokumenta. Pri nedatiranih sklicevanjih se uporablja zadnja
izdaja publikacije (vključno z dopolnili).

OPOMBA: Kadar je mednarodna publikacija spremenjena in so spremembe označene z (mod), se uporablja ustrezni
dokument EN/HD.
Standard Leto Naslov EN/HD Leto
1) 2)
IEC 61000-3-2 - Elektromagnetna združljivost (EMC) – EN 61000-3-2 2006
3-2. del: Mejne vrednosti – Mejne vrednosti
za oddajanje harmonskih tokov (vhodni tok
opreme do vključno 16 A na fazo)
1) 2)
IEC 61000-3-3 - Elektromagnetna združljivost (EMC) – EN 61000-3-3+ 1995
3-3. del: Mejne vrednosti – Omejitev popr. julij
vrednosti kolebanja napetosti in flikerja v
nizkonapetostnih napajalnih sistemih za
opremo z naznačenim tokom do 16 A in ni
priključena pod posebnimi pogoji
1) 2)
IEC 61000-3-11 - Elektromagnetna združljivost (EMC) – EN 61000-3-11 2000
3-11. del: Mejne vrednosti – Mejne
vrednosti napetostnih sprememb,
kolebanja napetosti in flikerja v javnih
nizkonapetostnih napajalnih sistemih –
Oprema z naznačenim tokom do vključno
75 A, ki je predmet pogojnega priklopa
1) 2)
IEC 61000-3-12 - Elektromagnetna združljivost (EMC) – EN 61000-3-12 2005
3-12. del: Mejne vrednosti – Mejne
vrednosti za harmonske tokove, ki jih
povzroča oprema, priključena na
nizkonapetostne napajalne sisteme z
naznačenim tokom, večjim od 16 A in
≤ 75 A po liniji
1) 2)
CISPR 14-1 - Elektromagnetna združljivost – Zahteve za EN 55014-1 2006
(električne) gospodinjske aparate,

električna ročna orodja in podobne aparate
– 1. del: Oddajanje
1)
Nedatirano sklicevanje.
2)
Veljavna izdaja ob izidu.
SIST EN 61000-6-3 : 2007
Standard Leto Naslov EN/HD Leto
CISPR 16-1-2 2003 Specifikacija za merilne naprave in metode EN 55016-1-2 2004
za merjenje radijskih motenj in odpornosti –
1-2. del: Merilne naprave za merjenje
radijskih motenj in odpornosti – Pomožna
oprema – Motnje po vodnikih
CISPR 16-2-1 2003 Specifikacija za merilne naprave in metode EN 55016-2-1 2004
za merjenje radijskih motenj in odpornosti –
2-1. del: Metode za merjenje radijskih
motenj in odpornosti – Merjenje motenj po
vodnikih
1) 2)
CISPR 16-2-3 - Specifikacija merilnih naprav in metod za EN 55016-2-3 2006
merjenje radijskih motenj in odpornosti –

2-3. del: Metode za merjenje radijskih
motenj in odpornosti – Merjenje sevanih
motenj
1) 2)
CISPR 16-4-2 - Specifikacija za merilne naprave in metode EN 55016-4-2 2004
za merjenje radijskih motenj in odpornosti –

4-2. del: Modeliranje negotovosti, statistike
in mejnih vrednosti – Negotovost pri
meritvah EMC
1) 2)
CISPR 22 - Oprema za informacijsko tehnologijo – EN 55022 2006
Karakteristike občutljivosti za radijske

motnje – Mejne vrednosti in merilne
metode
1)
Nedatirano sklicevanje.
2)
Veljavna izdaja ob izidu.
SIST EN 61000-6-3 : 2007
Dodatek ZZ
(informativni)
Vključitev bistvenih zahtev direktiv ES

Ta evropski standard je bil pripravljen v okviru mandata, ki sta ga Evropska komisija in Evropsko
združenje za prosto trgovino dala CENELEC in v obsegu svojega področja uporabe vključuje bistvene
zahteve, kot so podane v členu 4(a) Direktive ES 89/336/EGS in v členu 1(a) Priloge I k Direktivi
2004/108/ES ter bistvene zahteve člena 3.1(b) (samo oddajanje) Direktive ES 1999/5/ES.

Skladnost s tem standardom je eden od načinov doseganja skladnosti z določenimi bistvenimi
zahtevami zadevnih direktiv.
OPOZORILO: Za izdelke, ki jih zajema ta standard, lahko veljajo tudi druge zahteve in druge direktive.

SIST EN 61000-6-3 : 2007
MEDNARODNA ELEKTROTEHNIŠKA KOMISIJA

Elektromagnetna združljivost (EMC) –

6-3. del: Osnovni standardi – Standard oddajanja motenj v stanovanjskih,
poslovnih in manj zahtevnih industrijskih okoljih (IEC 61000-6-3:2006)

Predgovor k mednarodnemu standardu

1) IEC (Mednarodna elektrotehniška komisija) je svetovna organizacija za standardizacijo, ki združuje vse nacionalne
elektrotehnične komiteje (nacionalni komiteji IEC). Cilj IEC je pospeševati mednarodno sodelovanje v vseh vprašanjih
standardizacije s področja elektrotehnike in elektronike. V ta namen poleg drugih aktivnosti izdaja mednarodne standarde,
tehnične specifikacije, tehnična poročila, javnosti dostopne specifikacije (PAS) in vodila (v nadaljevanju: publikacije IEC). Za
njihovo pripravo so odgovorni tehnični odbori. Vsak nacionalni komite IEC, ki ga zanima obravnavana tema, lahko sodeluje
v tem pripravljalnem delu. Prav tako lahko v pripravi sodelujejo mednarodne organizacije ter vladne in nevladne ustanove, ki
so povezane z IEC. IEC deluje v tesni povezavi z mednarodno organizacijo za standardizacijo ISO skladno s pogoji,
določenimi v soglasju med obema organizacijama.
2) Uradne odločitve ali sporazumi IEC o tehničnih vprašanjih, pripravljeni v tehničnih odborih, v katerih so prisotni vsi
nacionalni komiteji, ki jih tema zanima, izražajo, kolikor je mogoče, mednarodno soglasje o obravnavani temi.
3) Publikacije IEC imajo obliko priporočil za njihovo uporabo na mednarodni ravni in jih kot takšne sprejmejo nacionalni
komiteji IEC. Čeprav IEC skuša na vse primerne načine zagotavljati točnost tehničnih vsebin v publikacijah IEC, IEC ne
more biti odgovoren za način, kako se določila uporabljajo, ter za mo
...