EN 60684-3-214:2014

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall

IEC 60684-3-214:2013 gives the requirements for two types of heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall with a nominal shrink ratio of 3:1. This sleeving has been found suitable for use at temperatures of up to 100 °C. Type A: Medium wall - internal diameter up to 200 mm typically; Type B: Thick wall - internal diameter up to 200 mm typically. These sleevings are normally supplied in colour black. Since these types of sleevings cover a significantly large range of sizes and wall thicknesses, Tables A.1 and A.2 of this document provides a guide to the range of sizes available. The actual size will be agreed between the user and supplier. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This third edition cancels and replaces the second edition published in 2005. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: Alignment with IEC 60684-3-247 (dual wall) since this Part 3 specification represents a single wall option using identical material. Keywords: heat-shrinkable, polyolefin sleeving

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 214: Polyolefin-Wärmeschrumpfschläuche, nicht-flammwidrig, dickwandig und mittlere Wanddicke

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 214: Gaines thermorétractables en polyoléfine, non ignifugées, à paroi épaisse et moyenne

La IEC 60684-3-214:2013 fournit les exigences relatives à deux types de gaines thermorétractables, en polyoléfine, non ignifugées, à paroi épaisse et moyenne, dont le rapport de rétreint nominal est 3:1. Ces gaines se sont avérées appropriées pour des températures allant jusqu'à 100 °C. Type A: Paroi moyenne - diamètre intérieur jusqu'à 200 mm typiquement; Type B: Paroi épaisse - diamètre intérieur jusqu'à 200 mm typiquement. Ces gaines sont normalement fournies en couleur noire. Comme ces types de gaines couvrent une gamme très étendue de tailles et d'épaisseurs de paroi, les Tableaux A.1 et A.2 du présent document fournissent un guide des tailles disponibles dans cette gamme. La taille réelle fera l'objet d'un accord entre l'utilisateur et le fournisseur. Les matériaux qui sont conformes à cette spécification satisfont à des niveaux de performances établis. Cependant, il convient que le choix d'un matériau par un utilisateur, pour une application spécifique, soit fondé sur les exigences réelles nécessaires pour obtenir une performance adéquate pour l'application concernée, et ne soit pas fondé sur cette seule spécification. Cette troisième édition annule et remplace la deuxième édition parue en 2005. Cette édition constitue une révision technique. Cette édition inclut la modification technique majeure suivante par rapport à l'édition précédente: Alignement avec la CEI 60684-3-247 (double paroi) étant donné que cette spécification de la Partie 3 représente une option à simple paroi utilisant un matériau identique. Mots clés : gaines thermorétractables, en polyoléfine gaines

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 214. list: Toplotno skrčljive poliolefinske cevi, neognjevarne, debela in srednje debela stena (IEC 60684-3-214:2013)

General Information

• Status: Withdrawn
• Publication Date: 20-Feb-2014
• Withdrawal Date: 23-Dec-2016
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: CLC/SR 15 - Insulating materials
• Drafting Committee: IEC/TC 15 - IEC_TC_15
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 12-Sep-2022
• Completion Date: 12-Sep-2022
• Ref Project: SIST EN 60684-3-214:2014 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall

Relations

• Replaces: EN 60684-3-214:2005 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, shrink ratio 3:1 - Thick and medium wall
• Effective Date: 28-Jan-2023
• Replaced By: EN IEC 60684-3-214:2019 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall
• Effective Date: 07-Jun-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.//Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall29.035.20PDWHULDOLPlastics and rubber insulating materialsICS:Ta slovenski standard je istoveten z:EN 60684-3-214:2014SIST EN 60684-3-214:2014en01-april-2014SIST EN 60684-3-214:2014SLOVENSKI
STANDARDSIST EN 60684-3-214:20081DGRPHãþD



SIST EN 60684-3-214:2014



EUROPEAN STANDARD EN 60684-3-214 NORME EUROPÉENNE
EUROPÄISCHE NORM February 2014
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2014 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-214:2014 E
ICS 29.035.20 Supersedes EN 60684-3-214:2005
English version
Flexible insulating sleeving -
Part 3: Specifications for individual types of sleeving -
Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall (IEC 60684-3-214:2013)
Gaines isolantes souples -
Partie 3: Spécifications pour types particuliers de gaines -
Feuille 214: Gaines thermorétractables en polyoléfine, non ignifugées, à paroi épaisse et moyenne (CEI 60684-3-214:2013)
Isolierschläuche -
Teil 3: Anforderungen für einzelne Schlauchtypen -
Blatt 214: Polyolefin-Wärmeschrumpfschläuche, nicht-flammwidrig, dickwandig und mittlere Wanddicke (IEC 60684-3-214:2013)
This European Standard was approved by CENELEC on 2013-12-24. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 60684-3-214:2014



EN 60684-3-214:2014 - 2 - Foreword The text of document 15/718/FDIS, future edition 3 of IEC 60684-3-214, prepared by IEC/TC 15 "Solid electrical insulating materials", was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60684-3-214:2014. The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-09-24 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-12-24
This document supersedes EN 60684-3-214:2005. EN 60684-3-214:2014 includes the following significant technical changes with respect to
EN 60684-3-214:2006:
Alignment with EN 60684-3-247 (dual wall) since this Part 3 specification represents a single wall option using identical material.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60684-3-214:2013 was approved by CENELEC as a European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60684-3 Series NOTE Harmonised in EN 60684-3 series (not modified). SIST EN 60684-3-214:2014



- 3 - EN 60684-3-214:2014 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60296 2012 Fluids for electrotechnical applications - Unused mineral insulating oils for transfo
...