HD 457 S1:1985
(Main)Code for designation of colours
Code for designation of colours
Applies to the text of descriptions, drawings, markings, etc., in the electrotechnical field and lays down a letter code for the designation of some distinct colour. Has the status of a basic safety publication in accordance with IEC Guide 104.
Code zur Farbkennzeichnung
Code de désignation de couleurs
S'applique aux textes de descriptions, schémas, marquages, etc., utilisés en électrotechnique et établit un code littéral pour la désignation de quelques couleurs distinctes. A le statut d'une publication fondamentale de sécurité conformément au Guide 104.
Code for designation of colours
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST HD 457 S1:2003
STANDARD
april 2003
Code for designation of colours
ICS 01.070; 29.020 Referenčna številka
SIST HD 457 S1:2003(en)
© Standard je založil in
...
This May Also Interest You
This document specifies letter codes for designation of colours and provides rules for their combination to designate colour combinations. The letter codes are intended to be applied in the technical documentation of electrical installations, electrical equipment and products, and in markings of electrical equipment and products. This basic safety publication focusing on safety essential requirements is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. This document does not specify any requirements for the encoding of colour properties, nor for their visual representation. Such requirements are under the responsibility of the different technical committees.
- Standard10 pagesEnglish languagesale 10% offe-Library read for×1 day
Establishes general rules for assigning particular meanings to certain visual, acoustsic and tactile indications. Has the status of a basic safety publication in accordance with IEC Guide 104.
- Standard35 pagesEnglish languagesale 10% offe-Library read for×1 day
- Standard – translation35 pagesSlovenian languagesale 10% offe-Library read for×1 day
This document specifies letter codes for designation of colours and provides rules for their combination to designate colour combinations. The letter codes are intended to be applied in the technical documentation of electrical installations, electrical equipment and products, and in markings of electrical equipment and products. This basic safety publication focusing on safety essential requirements is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. This document does not specify any requirements for the encoding of colour properties, nor for their visual representation. Such requirements are under the responsibility of the different technical committees.
- Standard10 pagesEnglish languagesale 10% offe-Library read for×1 day
Establishes general rules for assigning particular meanings to certain visual, acoustsic and tactile indications. Has the status of a basic safety publication in accordance with IEC Guide 104.
- Standard35 pagesEnglish languagesale 10% offe-Library read for×1 day
- Standard – translation35 pagesSlovenian languagesale 10% offe-Library read for×1 day
IEC 61169-70:2024, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) of HD-BNC series RF coaxial connectors together with the pro forma blank detail specification. HD-BNC series connectors with characteristic impedance of 75 Ω are used with RF cables or micro-strips in microwave, telecommunication, wireless and other fields. The operating frequency limit is up to 18 GHz. It also prescribes mating face dimensions for general purpose connectors, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series HD-BNC RF connectors. This specification indicates the recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
- Draft25 pagesEnglish languagesale 10% offe-Library read for×1 day
- 04-Apr-2024
- 31.220
- CLC/SR 46F
IEC 61300-2-44:2024 specifies a test to determine the influence of flexing under tensile load of the strain relief of fibre optic interconnecting devices or components. The intention is to simulate the number of flexing cycles which would typically be experienced during service life. This test is applied to both single fibre cable and multiple fibre cable. This fourth edition cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) replaced active monitoring with transient loss for measurements during test; b) harmonized recommended severities according to IEC 61753-1.
- Draft9 pagesEnglish languagesale 10% offe-Library read for×1 day
- 04-Apr-2024
- 33.180.20
- CLC/TC 86BXA
IEC 63305:2024 specifies methods and procedures for calibration of vector receivers in the frequency range 5 Hz to 10 kHz, which are applicable to vector receivers based on the two different principles. In addition, it describes an absolute method of inertial vector receiver calibration in air using optical interferometry. Usually, acoustic wave vector receivers are designed and constructed based on one of two principles. One is the sound pressure difference (gradient) principle. When measuring with this sensor, the vector receiver is rigidly fixed on a mount and supported in water. The other is the co-vibrating (inertial) principle. When measuring with this sensor, the vector receiver is suspended on a mount and supported in water in a non-rigid manner, which allows the vector receiver co-vibrate in the same direction as the sound particle in the sound wave field. Many methods have been used to calibrate vector receivers, such as free-field calibration, calibration in standing wave tube and calibration in a travelling wave tube.
- Draft55 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft4 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 60676:2024 This document specifies the basic test procedures, conditions and methods for establishing the main performance parameters and the main operational characteristics of furnaces for direct arc heating, forming arcs between the electrode and metal, such as electric arc furnaces using alternating current (EAF AC) or direct current (EAF DC), and ladle furnaces (LF), with rated power level above 500 kVA . This fourth edition cancels and replaces the third edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The structure has been redrafted according to IEC 60398:2015. b) The scope has been redrafted. c) The terms/definitions, normative references and bibliography have been updated and completed. d) The test methods and content from IEC 60398:2015 have been confirmed, replaced, or complemented with regards to direct arc furnaces (EAF, LF). e) The annexes from IEC 60398:2015 have been confirmed, replaced, or complemented with regards to direct arc furnaces (EAF, LF).
- Draft34 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 62836:2024 provides an efficient and reliable procedure to test the internal electric field in the insulating materials used for high-voltage applications, by using the pressure wave propagation (PWP) method. It is suitable for a planar and coaxial geometry sample with homogeneous insulating materials of thickness larger or equal to 0,5 mm and an electric field higher than 1 kV/mm, but it is also dependent on the thickness of the sample and the pressure wave generator. This first edition cancels and replaces IEC TS 62836 published in 2020. This edition includes the following significant technical changes with respect to IEC TS 62836: a) addition of Clause 12 for the measurement of space charge distribution in a planar sample; b) addition of Clause 13 for coaxial geometry samples; c) addition of Annex D with measurement examples for coaxial geometry samples; d) addition of a Bibliography; e) measurement examples for a planar sample have been moved from Clause 12 in IEC TS 62836 to Annex C.
- Draft43 pagesEnglish languagesale 10% offe-Library read for×1 day
- 04-Apr-2024
- 17.220.99
- 29.035.01
- CLC/SR 112
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.