EN 60264-3-1:2000/A1:2003

Packaging of winding wires - Part 3-1: Taper barrelled delivery spools - Basic dimensions

Amendment 1 - Replacement of Figure 1

Verpackung von Wickeldrähten - Teil 3-1: Lieferspulen mit konischem Kern - Maße

Conditionnement des fils de bobinage - Partie 3-1: Bobines de livraison à fût de forme conique - Dimensions de base

Amendement 1 - Remplacer la Figure 1

Packaging of winding wires - Part 3-1: Taper barelled delivery spools - Basic dimensions (IEC 60264-3-1:1999/A1:2003)

General Information

• Status: Published
• Publication Date: 09-Oct-2003
• Withdrawal Date: 30-Sep-2006
• ICS: 29.060.10 - Wires
• ICS: 55.060 - Spools. Bobbins
• Technical Committee: CLC/TC 55 - Winding wires
• Drafting Committee: IEC/TC 55 - IEC_TC_55
• Parallel Committee: IEC/TC 55 - IEC_TC_55
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 10-Oct-2003
• Completion Date: 10-Oct-2003
• Ref Project: SIST EN 60264-3-1:2001/A1:2004 - Packaging of winding wires -- Part 3-1: Taper barrelled delivery spools - Basic dimensions

Relations

• Amends: EN 60264-3-1:2000 - Packaging of winding wires - Part 3-1: Taper barrelled delivery spools - Basic dimensions
• Effective Date: 29-Jan-2023

Overview

EN 60264-3-1:2000/A1:2003 (IEC 60264-3-1:1999/A1:2003) is a CLC/CENELEC amendment that updates the European standard for the packaging of winding wires - specifically Part 3-1: Taper barrelled delivery spools – Basic dimensions. Amendment A1 was approved on 2003-10-01 and replaces the original Figure 1 to clarify the basic spool geometry and dimensional requirements used across the winding‑wire supply chain.

Key topics and requirements

• Scope: Establishes the basic dimensional specifications for taper‑barrelled delivery spools used to package winding wires.
• Revised Figure 1: The amendment replaces the original spool drawing with an updated schematic that sets out the primary geometric features and reference points (datum face).
• Typical dimensional features shown: cone angle (60°), nominal outer diameters (e.g., ∅100, ∅106, ∅125), central bore (e.g., ∅16 +0.5), radii (R3) and other detail dimensions (Detail X) that are applicable to spool types listed in Table 1 of the base standard.
• Tolerances and minimums: The figure includes key tolerances and minimum dimensions (for example minimum spacing and axial lengths) that manufacturers must observe; these are illustrated on the updated drawing and referenced against spool types.
• Normative references and implementation: The amendment follows IEC TC 55 (Winding wires) procedures and was published to be implemented as a national standard by CENELEC members.

Applications and who uses it

• Winding‑wire manufacturers and packagers: Ensure spools meet consistent basic dimensions for winding, storage and transport.
• Spool and drum producers: Design and manufacture taper‑barrelled delivery spools to the standardized geometry and tolerances.
• Motor, transformer and coil manufacturers: Specify compatible spool dimensions for reliable feed, automated winding and inventory handling.
• Quality assurance and procurement teams: Use the standard to verify incoming wire packs, enforce supplier conformity, and include requirements in purchase specifications.
• Regulatory and standards bodies: Reference this amendment when harmonizing national standards or conducting conformity assessments.

Related standards

• IEC 60264 series (Packaging of winding wires) - this part (3-1) is one element of the broader series covering different spool types and packaging methods.
• National adoptions and translations by CENELEC members - this amendment is to be implemented identically at national level.

Keywords: EN 60264-3-1, IEC 60264-3-1, taper barrelled delivery spools, winding wire packaging, spool dimensions, CENELEC amendment A1, basic dimensions, spool tolerances.

Standards Content (Sample)

SLOVENSKI SIST EN 60264-3-
1:2001/A1:2004
STANDARD
februar 2004
Packaging of winding wires - Part 3-1: Taper barelled delivery spools - Basic
dimensions (IEC 60264-3-1:1999/A1:2003)
ICS 29.060.10; 55.060 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 60264-3-1/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM October 2003

ICS 29.060.10;55.060
English version
Packaging of winding wires
Part 3-1: Taper barrelled delivery spools –
Basic dimensions
(IEC 60264-3-1:1999/A1:2003)
Conditionnement des fils de bobinage Verpackung von Wickeldrähten
Partie 3-1: Bobines de livraison à fût Teil 3-1: Lieferspulen mit konischem Kern -
de forme conique – Maße
Dimensions de base (IEC 60264-3-1:1999/A1:2003)
(CEI 60264-3-1:1999/A1:2003)
This amendment A1 modifies the European Standard EN 60264-3-1:2000; it was approved by CENELEC
on 2003-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this amendment the status of a national standard without any
alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60264-3-1:2000/A1:2003 E

Foreword
The text of document 55/837/FDIS, future amendment 1 to IEC 60264-3-1:1999, prepared by
IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel v
...