EN 60060-3:2006

High voltage test techniques - Part 3: Definitions and requirements for on-site tests

Applicable to the following on-site test voltages and in service stresses, which are in relation to IEC 60060-1: direct voltage;alternating voltage; lightning impulse voltage of aperiodic or oscillating shape: switching impulse voltage of aperiodic or oscillating shape.

Hochspannungs-Prüftechnik - Teil 3: Begriffe und Anforderungen für Vor-Ort-Prüfungen

Techniques des essais à haute tension - Partie 3: Définitions et prescriptions pour des essais sur site

Visokonapetostne preskusne tehnike – 3. del: Definicije in zahteve za preskušanje na kraju samem (IEC 60060-3:2006)

General Information

• Status: Published
• Publication Date: 09-Mar-2006
• Withdrawal Date: 31-Jan-2009
• ICS: 17.220.20 - Measurement of electrical and magnetic quantities
• ICS: 19.080 - Electrical and electronic testing
• Technical Committee: CLC/SR 42 - High-voltage testing techniques
• Drafting Committee: IEC/TC 42 - IEC_TC_42
• Parallel Committee: IEC/TC 42 - IEC_TC_42
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 10-Mar-2006
• Completion Date: 10-Mar-2006
• Ref Project: SIST EN 60060-3:2006 - High voltage test techniques -- Part 3: Definitions and requirements for on-site tests

Standards Content (Sample)

SLOVENSKI SIST EN 60060-3:2006

STANDARD
julij 2006
Visokonapetostne preskusne tehnike – 3. del: Definicije in zahteve za
preskušanje na kraju samem (IEC 60060-3:2006)
High voltage test techniques – Part 3: Definitions and requirements for on-site tests
(IEC 60060-3:2006)
ICS 19.080 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD
EN 60060-3
NORME EUROPÉENNE
March 2006
EUROPÄISCHE NORM
ICS 17.220.20; 19.080
English version
High voltage test techniques
Part 3: Definitions and requirements for on-site tests
(IEC 60060-3:2006)
Techniques des essais à haute tension Hochspannungs-Prüftechnik
Partie 3: Définitions et prescriptions Teil 3: Begriffe und Anforderungen
pour des essais sur site für Vor-Ort-Prüfungen
(CEI 60060-3:2006) (IEC 60060-3:2006)

This European Standard was approved by CENELEC on 2006-02-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60060-3:2006 E
Foreword
The text of document 42/203/FDIS, future edition 1 of IEC 60060-3, prepared by IEC TC 42, High-voltage
testing techniques, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60060-3 on 2006-02-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-11-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2009-02-01
This European Standard makes reference to International Standards. Where the International Standard
referred to has been endorsed as a European Standard or a home-grown European Standard exists, this
European Standard shall be applied instead. Pertinent information can be found on the CENELEC web
site.
__________
Endorsement notice
The text of the International Standard IEC 60060-3:2006 was approved by CENELEC as a European
Standard without any modification.
__________
INTERNATIONAL IEC
STANDARD 60060-3
First edition
2006-02
High-voltage test techniques –
Part 3:
Definitions and requirements
for on-site testing
 IEC 2006  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale V
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

– 2 – 60060-3  IEC:2006(E)
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 Scope.7
2 Normative references .7
3 Terms and definitions .7
4 Common tests and checks on a measuring system .12
4.1 Acceptance test.12
4.2 Performance test.12
4.3 Performance check.12
4.4 Record of performance.13
5 Tests with direct voltage.13
5.1 General .13
5.2 Definitions for direct voltage tests.13
5.3 Test voltage .14
5.4 Measurement of the test voltage.14
5.5 Tests and checks on measuring systems.15
5.6 Withstand voltage test procedure .15
6 Tests with alternating voltage .15
6.1 General .15
6.2 Definitions for alternating voltage tests.15
6.3 Test voltage .16
6.4 Measurement of the test voltage.17
6.5 Tests and checks on measuring systems.18
6.6 Withstand voltage test procedure .18
7 Tests with lightning impulse voltage .18
7.1 General .18
7.2 Definitions for lightning impulse voltage tests .18
7.3 Test voltage .21
7.4 Measurement of the test voltage and determination of the impulse voltage
shape .22
7.5 Tests and checks on measuring systems.22
7.6 Withstand voltage test procedures.23
8 Tests with switching impulse voltage .23
8.1 General .23
8.2 Definitions for switching impulse voltage tests.23
8.3 Test voltage .26
8.4 Measurement of the test voltage and determination of the impulse shape.26
8.5 Tests and checks on measuring systems.27
8.6 Withstand voltage test procedures.27
9 Tests with very low frequency voltages.28
9.1 General .28
9.2 Definitions for very low frequency voltage tests .28
9.3 Test voltage .29
9.4 Measurement of the test voltage.29
9.5 Tests and checks on measuring systems.30
9.6 Test procedure .30

60060-3  IEC:2006(E) – 3 –
10 Tests with damped alternating voltages .30
10.1 General .30
10.2 Definitions for damped alternating voltage tests .30
10.3 Test voltage .31
10.4 Measurement of the test voltage.32
10.5 Tests and checks on measuring systems.32
10.6 Test procedure .33

Figure 1 – Aperiodic lightning impulse .19
Figure 2 – Oscillating lightning impulse.20
Figure 3 – Aperiodic switching impulse .24
Figure 4 – Oscillating switching impulse.25
Figure 5 – Damped alternating voltage (f = 1 kHz, D = 0,2) .31
r f
– 4 – 60060-3  IEC:2006(E)
INTERNATIONAL ELECTROECHNICAL COMMISSION
____________
HIGH-VOLTAGE TEST TECHNIQUES –

Part 3: Definitions and requirements for on-site testing

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60060-3 has been prepared by IEC techni
...