EN 60301:2012

Preferred diameters of wire terminations of capacitors and resistors

IEC 60301:2012 gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment. This third edition cancels and replaces the second edition, published in 1971, and its Amendment 1, published in 1972, and constitutes a technical revision. The main technical changes with respect to the second edition are the following: - employment of SI units only in the normative part of this standard, causing transfer of all imperial dimensions from Table 1 to the informative Annex A, - addition of two smaller diameters of wire terminations in Table 1, and - tightening of the tolerance ranges defined by minimum and maximum diameters in Table 1.

Bevorzugte Durchmesser für Anschlussdrähte an Kondensatoren und Widerständen

Valeurs préférentielles des diamètres des fils de sorties des condensateurs et résistances

La CEI 60301:2012 donne une série de valeurs préférentielles pour les diamètres des fils de sorties finis des condensateurs et résistances destinés à être utilisés dans les équipements électroniques. Cette troisième édition annule et remplace la deuxième édition parue en 1971, ainsi que son Amendement 1, paru en 1972, et constitue une révision technique. Les modifications techniques principales par rapport à la deuxième édition sont les suivantes: - utilisation d'unités SI uniquement dans la partie normative de la présente norme, entraînant un déplacement de toutes les dimensions impériales du Tableau 1 à l'Annexe A, informative, - ajout de deux diamètres plus petits de fils de sorties dans le Tableau 1, et - abaissement des plages de tolérances définies par les diamètres minimal et maximal du Tableau 1.

Preferenčni premeri žičnih priključkov kondenzatorjev in uporov

Ta mednarodni standard podaja niz preferenčnih premerov končnih žičnih priključkov kondenzatorjev in uporov pri uporabi v elektronski opremi.

General Information

• Status: Published
• Publication Date: 04-Oct-2012
• ICS: 31.040 - Resistors
• ICS: 31.060 - Capacitors
• Technical Committee: CLC/TC 40XA - CLC/TC 40XA
• Drafting Committee: IEC/TC 40 - IEC_TC_40
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 08-Apr-2020
• Ref Project: SIST EN 60301:2012 - Preferred diameters of wire terminations of capacitors and resistors

Relations

• Replaces: HD 349 S1:1977 - Preferred diameters of wire terminations of capacitors and resistors
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60301:2012
01-december-2012
1DGRPHãþD
SIST HD 349 S1:2004
3UHIHUHQþQLSUHPHULåLþQLKSULNOMXþNRYNRQGHQ]DWRUMHYLQXSRURY
Preferred diameters of wire terminations of capacitors and resistors
Valeurs préférentielles des diamètres des fils de sorties des condensateurs et
résistances
Ta slovenski standard je istoveten z: EN 60301:2012
ICS:
31.040.01 Upori splošno Resistors in general
31.060.01 Kondenzatorji na splošno Capacitors in general
SIST EN 60301:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60301:2012

---------------------- Page: 2 ----------------------

SIST EN 60301:2012

EUROPEAN STANDARD
EN 60301

NORME EUROPÉENNE
October 2012
EUROPÄISCHE NORM

ICS 31.040; 31.060 Supersedes HD 349 S1:1977


English version


Preferred diameters of wire terminations of capacitors
and resistors
(IEC 60301:2012)


Valeurs préférentielles des diamètres  Bevorzugte Durchmesser
des fils de sorties des condensateurs für Anschlussdrähte an Kondensatoren
et résistances und Widerständen
(CEI 60301:2012) (IEC 60301:2012)





This European Standard was approved by CENELEC on 2012-08-17. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60301:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60301:2012
EN 60301:2012 - 2 -
Foreword
The text of document 40/2153/FDIS, future edition 3 of IEC 60301, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60301:2012.
The following dates are fixed:
(dop) 2013-05-17
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-08-17
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes HD 349 S1:1977.

EN 60301:2012 includes the following significant technical changes with respect to HD 349 S1:1977:
- employment of SI units only in the normative part of this standard, causing transfer of all imperial
dimensions from Table 1 to the informative Annex A;
- addition of two smaller diameters of wire terminations in Table 1; and
- tightening of the tolerance ranges defined by minimum and maximum diameters in Table 1.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 60301:2012 was approved by CENELEC as a European
Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 60301:2012



IEC 60301

®


Edition 3.0 2012-07




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Preferred diameters of wire terminations of capacitors and resistors



Valeurs préférentielles des diamètres des fils de sorties des condensateurs et


résistances

















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX F


ICS 31.040; 31.060 ISBN 978-2-83220-225-8



Warning! Make sure that you obtained this publication from an authorized distributor.

Atten
...