EN 60717:2012

Method for the determination of the space required by capacitors and resistors with unidirectional terminations

IEC 60717:2012 applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations. NOTE: Instead of measuring the actual space, it may be sufficient to ensure that a component fits into the maximum space for which it is designed. This may be achieved by means of fixed gauges. The main technical changes with respect to the first edition are the following: - employment of the millimetre-based grid, the preferred grid system given in IEC 60097, - employment of SI units only, causing deletion of the imperial dimensions from Table 1, - reduction of the tolerance on the chamfer depth in Figure 1, and - introduction of requirements on information to be given in a relevant specification.

Verfahren zum Bestimmen des Raumbedarfs bei Kondensatoren und Widerständen mit einseitigen Anschlüssen

Méthode pour la détermination de l'encombrement des condensateurs et résistances à sorties unilatérales

La CEI 60717:2012 s'applique aux condensateurs et résistances à fils de sorties unilatérales, destinés à être utilisés dans les équipements électroniques. Cette norme donne une méthode pour la détermination de l'encombrement des condensateurs et résistances à fils de sorties unilatérales. NOTE: Au lieu de mesurer l'encombrement réel, il peut être suffisant de s'assurer qu'un composant s'adapte à l'encombrement maximal pour lequel il a été défini. Cela peut être réalisé au moyen de calibres fixes. Les modifications techniques principales par rapport à la première édition sont les suivantes: - utilisation de la grille basée sur le millimètre, système de grille préférentiel donné dans la CEI 60097, - utilisation d'unités SI uniquement, entraînant la suppression des dimensions impériales du Tableau 1, - réduction de la tolérance pour la profondeur du chanfrein à la Figure 1, et - introduction des exigences relatives aux informations à fournir dans une spécification applicable.

Metoda za ugotavljanje potrebnega prostora za kondenzatorje in upore z enostranskimi priključki

Ta mednarodni standard velja za kondenzatorje in upore z enostranskimi priključki žice, namenjene za uporabo v elektronski opremi. Ta standard določa metodo za ugotavljanje potrebnega prostora za kondenzatorje in upore z enostranskimi priključki.

General Information

• Status: Published
• Publication Date: 26-Jul-2012
• Withdrawal Date: 18-Jun-2015
• ICS: 31.040 - Resistors
• ICS: 31.060 - Capacitors
• Technical Committee: CLC/SR 40 - Capacitors and resistors for electronic equipment
• Drafting Committee: IEC/TC 40 - IEC_TC_40
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 27-Jul-2012
• Completion Date: 27-Jul-2012
• Ref Project: SIST EN 60717:2012 - Method for the determination of the space required by capacitors and resistors with unidirectional terminations

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Verfahren zum Bestimmen des Raumbedarfs bei Kondensatoren und Widerständen mit einseitigen AnschlüssenMéthode pour la détermination de l'encombrement des condensateurs et résistances à sorties unilatéralesMethod for the determination of the space required by capacitors and resistors with unidirectional terminations31.060.01Kondenzatorji na splošnoCapacitors in general31.040.01Upori splošnoResistors in generalICS:Ta slovenski standard je istoveten z:EN 60717:2012SIST EN 60717:2012en01-september-2012SIST EN 60717:2012SLOVENSKI
STANDARD



SIST EN 60717:2012



EUROPEAN STANDARD EN 60717 NORME EUROPÉENNE
EUROPÄISCHE NORM July 2012
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60717:2012 E
ICS 31.040; 31.060
English version
Method for the determination of the space required by capacitors and resistors with unidirectional terminations (IEC 60717:2012)
Méthode pour la détermination de l'encombrement des condensateurs et résistances à sorties unilatérales (CEI 60717:2012)
Verfahren zum Bestimmen des Raumbedarfs bei Kondensatoren und Widerständen mit einseitigen Anschlüssen(IEC 60717:2012)
This European Standard was approved by CENELEC on 2012-06-19. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 60717:2012



EN 60717:2012 - 2 -
Foreword The text of document 40/2108/CDV, future edition 2 of IEC 60717, prepared by IEC TC 40, "Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60717:2012.
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-03-19 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-06-19
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60717:2012 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated: IEC 61192-3 NOTE
Harmonized as EN 61192-3.
SIST EN 60717:2012



- 3 - EN 60717:2012 Annex ZA (normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60097 - Grid systems for printed circuits EN 60097 -
IEC 60294 - Measurement of the dimensions of a cylindrical component with axial terminations EN 60294 -1)
IEC 60301 - Preferred diameters of wire terminations of capacitors and resistors EN 60301 -1)
1) To be published. SIST EN 60717:2012



SIST EN 60717:2012



IEC 60717 Edition 2.0 2012-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Method for the determination of the space required by capacitors and resistors with unidirectional terminations
Méthode pour la détermination de l'encombrement des condensateurs et résistances à sorties unilatérales
INTERNAT
...