iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 50298:1998

(Main)

Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements

Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements

The object of this standard is to specify definitions, classifications, characteristics and test requirements of enclosures to be used as part of switchgear and controlgear assemblies in accordance with the EN 60439 series, the rated voltage of which does not exceed 1 000 V a.c. at frequencies not exceeding 1 000 Hz, or 1 500 V d.c. and suitable for general use for either indoor or outdoor applications. This standard applies to empty enclosures, prior to the incorporation of switchgear and controlgear components by the user, as supplied by the enclosure manufacturer. This standard does not apply to enclosures which are covered by other specific products standards (e.g. IEC 60670, household and similar installations). Compliance with the safety requirements of the applicable product standard is the responsibility of the final assembly manufacturer. This standard may serve as a basis for other technical committees

Leergehäuse für Niederspannungsschaltgerätekombinationen - Allgemeine Anforderungen

Enveloppes destinées aux ensembles d'appareillage à basse tension - Règles générales pour les enveloppes vides

Prazni okrovi za sestave nizkonapetostnih stikalnih in krmilnih naprav – Splošne zahteve

General Information

Status
Withdrawn
Publication Date
19-Oct-1998
Withdrawal Date
31-Mar-1999
ICS
29.130.20 - Low voltage switchgear and controlgear
Technical Committee
CLC/TC 17D - Low-voltage switchgear and controlgear assemblies
Drafting Committee
IEC/SC 17D - IEC_SC_17D
Parallel Committee
IEC/SC 17D - IEC_SC_17D
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Dec-2006
Completion Date
01-Dec-2006
Directive
2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
73/23/EEC - Electrical equipment designed for use within certain voltage limits
Ref Project
SIST EN 50298:2000 - Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements

Relations

Replaced By
EN 62208:2003 - Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements
Effective Date
29-Jan-2023

Buy Standard

EN 50298:2000EN 50298:2000
PreviousNext
Standard
EN 50298:2000
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50298:2000
01-september-2000
Prazni okrovi za sestave nizkonapetostnih stikalnih in krmilnih naprav – Splošne
zahteve
Empty enclosures for low-voltage switchgear and controlgear assemblies - General
requirements
Leergehäuse für Niederspannungsschaltgerätekombinationen - Allgemeine
Anforderungen
Enveloppes destinées aux ensembles d'appareillage à basse tension - Règles générales
pour les enveloppes vides
Ta slovenski standard je istoveten z: EN 50298:1998
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
SIST EN 50298:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50298:2000

---------------------- Page: 2 ----------------------

SIST EN 50298:2000

---------------------- Page: 3 ----------------------

SIST EN 50298:2000

---------------------- Page: 4 ----------------------

SIST EN 50298:2000

---------------------- Page: 5 ----------------------

SIST EN 50298:2000

---------------------- Page: 6 ----------------------

SIST EN 50298:2000

---------------------- Page: 7 ----------------------

SIST EN 502
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61439-1:2021/AC:2023-11(Corrigendum)
Low-voltage switchgear and controlgear assemblies - Part 1: General rules
SIST EN IEC 61439-1:2021/AC:2024
  • Corrigendum
    3 pages
    French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62208:2023(Main)
Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements
SIST EN IEC 62208:2023

IEC 62208:2023 applies to empty enclosures, as provided by the enclosure manufacturer, prior to the incorporation of switchgear and controlgear components by the assembly manufacturer. This document specifies general definitions, classifications, characteristics and test requirements of enclosures to be used as part of switchgear and controlgear assemblies (e.g. in accordance with the product standard in the IEC 61439 series), the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC, and suitable for general use for either indoor or outdoor applications. This third edition cancels and replaces the second edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) consideration of the modifications introduced in IEC 61439-1:2020; b) alignment of test procedures with the newest relevant standards.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61439-5:2023(Main)
Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
SIST EN IEC 61439-5:2023

IEC 61439-5:2023 is available as IEC 61439-5:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61439-5:2023 defines the specific requirements for public electricity network distribution assemblies (PENDAs). PENDAs have the following criteria: - used for the distribution of electrical energy in three phase systems for which the rated voltage does not exceed 1 000 V AC (see Figure 101 for a typical distribution network) and DC systems not exceeding 1 500 V DC; - stationary; - open type assemblies are not covered by this document; - suitable for installation in places where only skilled persons have access for their use, however, outdoor types can be installed in situations that are accessible to ordinary persons - intended for use in energy distribution in public power grids; - indoor use: assemblies for installation inside of electric power substations; - outdoor use: assemblies containing an enclosure suitable for open air installation. This third edition cancels and replaces the second edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) omission of the requirement to conduct mechanical tests at -25 °C when enclosures are made of a metallic material; b) addition of assumed loading factors generation supplies and electric vehicle charging applications; c) additional dielectric tests when a PENDA is used in a distribution substation with separate HV and LV earths; d) further clarification of representative samples for design verification.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61439-7:2023(Main)
Low-voltage switchgear and controlgear assemblies - Part 7: Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations
SIST EN IEC 61439-7:2023

Clause 1 of IEC 61439-1:2020 is applicable except as follows. Replacement: This part of IEC 61439 defines the specific requirements for Assemblies for the following applications: marinas, camping sites, market squares and electric vehicle charging stations as follows: - Assemblies for which the rated voltage does not exceed 1 000 V AC or 1 500 V DC; - Assemblies intended for use in connection with the generation, transmission, distribution and conversion of electric energy, and for the control of electric energy consuming equipment; - Assemblies operated by ordinary persons (e.g. to plug and unplug of electrical equipment); - Assemblies intended to be installed and used in market squares, marinas, camping sites and other similar sites accessible to the public including temporary installations; - Assemblies intended for charging stations for electric vehicles (AEVCS) for Mode 3 and Mode 4. They are designed to integrate the functionality and additional requirements for electric vehicle conductive charging systems according to IEC 61851-1:2017. NOTE 1 Throughout this document, the terms AMHS (see 3.1.701), ACCS (see 3.1.702), AMPS (see 3.1.703), AEVCS (see 3.1.704) are used for low-voltage switchgear and controlgear assemblies intended for use respectively in marinas and similar locations (AMHS), camping sites and similar locations (ACCS), market squares and other similar external public sites (AMPS) and charging stations (AEVCS). The term assemblies is used for indicating all these boards. This standard is not applicable to assemblies intended to be installed on board of ships, houseboats, pleasure crafts and similar vessels. For the correct selection of the switching devices and components, the following standards apply: - IEC 60364-7-709 (AMHS) or - IEC 60364-7-708 (ACCS) or - IEC 60364-7-740 (AMPS) or - IEC 60364-7-722 (AEVCS). This document applies to all assemblies whether they are designed, manufactured and verified on a one-off basis or fully standardised and manufactured in quantity. The manufacturing and/or assembling may be carried out other than by the original manufacturer (see 3.10.1 of IEC 61439-1:2020). This document does not apply to individual devices and self-contained components such as circuit breakers, fuse switches, electronic equipment, which comply with their relevant product standards. NOTE 2 Where electrical equipment is directly connected to public low-189 voltage supply system and equipped with an energy meter for billing of the legal provider of the low-voltage supply, additional particular requirements based on national regulations apply, if any. This document does not apply to boxes and enclosures for electrical accessories for household and similar fixed electrical installations as defined in IEC 60670-24.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-6-2:2023/AC:2023-07(Corrigendum)
Low-voltage switchgear and controlgear - Part 6-2: Multiple function equipment - Control and protective switching devices (or equipment) (CPS)
SIST EN IEC 60947-6-2:2023/AC:2023
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-6-1:2023(Main)
Low-voltage switchgear and controlgear - Part 6-1: Multiple function equipment - Transfer switching equipment
SIST EN IEC 60947-6-1:2023

This part of EN 60947applies to transfer switching equipment (TSE) to be used in power systems with interruption of the supply to the load during transfer, the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-8:2023(Main)
Low-voltage switchgear and controlgear - Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines
SIST EN IEC 60947-8:2023

This part of IEC 60947 series specifies requirements for control units, which control a switching device in response to the PTC thermistors incorporated in rotating electrical machines and the industrial application. It specifies requirements for that type of system comprising a positive temperature coefficient (PTC) thermistor having particular characteristics, and its associated control unit. This document includes: - the characteristics, construction, performance and tests of the control unit; and - its association with a PTC thermistor designated "Mark A". This document does not cover: - the incorporation of thermal protections into rotating machines and their maximum winding temperature. See IEC 60034-11; - use of the product within explosive atmospheres (see IEC 60079 (all parts)); - software and firmware requirements; NOTE 1 Guidance on embedded software is given in IEC TR 63201. - cyber security aspects (see IEC TS 63208). NOTE 2 It is not possible to specify all the requirements for the operating characteristics of a control unit, as they are dependent on some aspects of the PTC thermistors. Some aspects of the requirements of the thermal protector system can only be specified when account is taken of the characteristics of the rotating machine to be protected and the method of installation of the PTC thermistor within the machine.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-4-2:2023(Main)
Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - Semiconductor motor controllers, starters and soft-starters
SIST EN IEC 60947-4-2:2023

IEC 60947-4-2:2020 applies to semiconductor motor controllers, starters and soft-starters which can include a series mechanical switching device, intended to be connected to circuits the rated voltage of which does not exceed 1 000 V AC. This fourth edition cancels and replaces the third edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - scope exclusions; - editorial correction of notes and hanging paragraphs; - reference to IEC 62683-1; - safety aspects related to: - general aspects; - limited energy circuits; - electronic circuits; - mention of dedicated wiring accessories; - power consumption measurement; - alignment to IEC 60947-1:2020.

  • Standard
    117 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-6-2:2023(Main)
Low-voltage switchgear and controlgear - Part 6-2: Multiple function equipment - Control and protective switching devices (or equipment) (CPS)
SIST EN IEC 60947-6-2:2023

Applies to control and protective switching devices (or equipment) (CPS), the main contacts of which are intended to be connected to circuits of rated voltage not exceeding 1 000 V a.c. or 1 500 V d.c. CPSs are intended to provide both protective and control functions for circuits and are operated otherwise than by hand. They may also fulfil additional functions, such as isolation.

  • Standard
    116 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-1:2021/AC:2023-01(Corrigendum)
Low-voltage switchgear and controlgear - Part 1: General rules
SIST EN IEC 60947-1:2021/AC:2023
  • Corrigendum
    4 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day