EN 60745-2-18:2009
(Main)Hand-held motor-operated electric tools - Safety - Part 2-18: Particular requirements for strapping tools
Hand-held motor-operated electric tools - Safety - Part 2-18: Particular requirements for strapping tools
Deals with the safety of hand-held motor-operated or magnetically driven tools, specific requirements for strapping tools. The rated voltage being not more than 250 V for single-phase a.c. or d.c., and 440 V for three-phase a.c. tools.
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-18: Besondere Anforderungen für Umreifungswerkzeuge
Outils électroportatifs à moteur - Sécurité - Partie 2-18: Règles particulières pour les outils de cerclage
Traite de la sécurité des outils dont la tension assignée n'est pas supérieure à 250 V en courant monophasé alternatif ou courant continu et 440 V en courant alternatif triphasé. Complète ou modifie les articles correspondants de la CEI 60745-1.
Električna ročna orodja - Varnost - 2-18. del: Posebne zahteve za ročno orodje za zategovanje pakirnih trakov (IEC 60745-2-18:2003 + A1:2008, spremenjen)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60745-2-18:2009
01-december-2009
1DGRPHãþD
SIST EN 60745-2-18:2004
(OHNWULþQDURþQDRURGMD9DUQRVWGHO 3RVHEQH]DKWHYH]DURþQRRURGMH]D
]DWHJRYDQMHSDNLUQLKWUDNRY ,(& $ VSUHPHQMHQ
Hand-held motor-operated electric tools - Safety -- Part 2-18: Particular requirements for
strapping tools
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit -- Teil 2-18: Besondere
Anforderungen für Umreifungswerkzeuge
Outils électroportatifs à moteur - Sécurité -- Partie 2-18: Règles particulières pour les
outils de cerclage
Ta slovenski standard je istoveten z: EN 60745-2-18:2009
ICS:
25.140.20 (OHNWULþQDRURGMD Electric tools
55.040 0DWHULDOLLQSULSRPRþNL]D Packaging materials and
SDNLUDQMH accessories
SIST EN 60745-2-18:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60745-2-18:2009
---------------------- Page: 2 ----------------------
SIST EN 60745-2-18:2009
EUROPEAN STANDARD
EN 60745-2-18
NORME EUROPÉENNE
September 2009
EUROPÄISCHE NORM
ICS 25.140.20 Supersedes EN 60745-2-18:2004 + corr. Dec.2005 + A1:2008 + A11:2007
English version
Hand-held motor-operated electric tools -
Safety -
Part 2-18: Particular requirements for strapping tools
(IEC 60745-2-18:2003, modified + A1:2008)
Outils électroportatifs à moteur - Handgeführte motorbetriebene
Sécurité - Elektrowerkzeuge -
Partie 2-18: Règles particulières Sicherheit -
pour les outils de cerclage Teil 2-18: Besondere Anforderungen
(CEI 60745-2-18:2003, modifiée + für Umreifungswerkzeuge
A1:2008) (IEC 60745-2-18:2003, modifiziert +
A1:2008)
This European Standard was approved by CENELEC on 2009-07-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60745-2-18:2009 E
---------------------- Page: 3 ----------------------
SIST EN 60745-2-18:2009
EN 60745-2-18:2009 - 2 -
Foreword
The text of the International Standard IEC 60745-2-18:2003, prepared by SC 61F (transformed into
IEC TC 116, Safety of hand-held motor-operated electric tools), together with the common
modifications prepared by the Technical Committee CENELEC TC 61F (transformed into TC 116) was
submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 60745-2-18
on 2004-03-01.
A draft amendment (prAA) was prepared to align Subclause 6.2 with the new Subclause 6.2 in
EN 60745-1. Moreover, vibration values determined with the new 6.2 are complying with the
requirements of the Physical Agents Directive Vibration 2002/44/EC. The text of the draft was
submitted to the Unique Acceptance Procedure and was approved by CENELEC as amendment A11
to EN 60745-2-18:2004 on 2007-06-01.
The text of document 61F/677/CDV, future amendment 1 to IEC 60745-2-18:2003 was submitted to
the IEC-CENELEC parallel Unique Acceptance Procedure and was approved by CENELEC as
amendment A1 to EN 60745-2-18:2004 on 2008-04-01.
A further draft amendment (prAB), extending Annex ZZ to include the new MD 2006/42/EC, was
submitted to the formal vote.
The combined texts were approved by CENELEC as a new edition of EN 60745-2-18 on 2009-07-01.
This European Standard supersedes EN 60745-2-18:2004 + corrigendum December 2005 +
A11:2007 + A1:2008.
The following dates were fixed:
– latest date by which the EN has to be implemented (dop) 2010-07-01
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2011-04-01
with the EN have to be withdrawn
This standard is divided into two parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could come within the
scope of this standard;
Part 2: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and supports the essential requirements of
EC Directive 98/37/EC (Machinery Directive), amended by EC Directive 98/79/EC, and of EC Directive
2006/42/EC. See Annexes ZZA and ZZB.
Compliance with the clauses of Part 1 together with this Part 2 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
Warning: Other requirements and other EC Directives can be applicable to the products falling
within the scope of this standard.
This standard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2.
---------------------- Page: 4 ----------------------
SIST EN 60745-2-18:2009
- 3 - EN 60745-2-18:2009
This Part 2-18 is to be used in conjunction with EN 60745-1:2009. When this standard states
"addition", "modification" or "replacement", the relevant text of Part 1 is to be adapted accordingly.
Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101.
Subclauses, tables and figures which are additional to those in IEC 60745-2-18 are prefixed “Z”.
NOTE In this standard the following print types are used:
– Requirements proper;
– Test specifications;
– Explanatory matter.
---------------------- Page: 5 ----------------------
SIST EN 60745-2-18:2009
EN 60745-2-18:2009 - 4 -
Endorsement notice
The text of the International Standard IEC 60745-2-18:2003 + A1:2008 was approved by CENELEC
as a European Standard with agreed common modifications as given below.
COMMON MODIFICATIONS
6 Void
Replace by:
6 Environmental requirements
This clause of Part 1 is applicable except as follows:
6.1.2.4 Modification:
Strapping tools are suspended with the motor axis horizontal.
6.1.2.5 Modification:
Strapping tools are tested at no-load.
6.2 Vibration
6.2.6.3 Operating conditions
Modification:
Table Z101 – Operating conditions for strapping tools
Orientation Clinching straps around a test package. The test package is a wooden box 1 m
cubic with an internal bracing to prevent collapsing
Tool bit Strapping material of medium width
Grip force Hold the machine with normal gripping force, avoiding excessive gripping force
Test cycle One test cycle is given by clinching one strap.
Three series of five consecutive tests shall be carried out using a different
operator for each series.
6.2.7.2 Declaration of the vibration total value
Addition:
The vibration total value a of the handle with the highest emission and the uncertainty K shall be
h
declared.
---------------------- Page: 6 ----------------------
SIST EN 60745-2-18:2009
- 5 - EN 60745-2-18:2009
21 Construction
Add:
21.Z1 This clause of Part 1 is not applicable.
---------------------- Page: 7 ----------------------
SIST EN 60745-2-18:2009
EN 60745-2-18:2009 - 6 -
Add the following annex:
Annex ZZ
(informative)
Coverage of Essential Requirements of EC Directives
Annex ZZA
(informative)
Coverage of Essential Requirements of Directive 98/37/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EC Directive 98/37/EC (Machinery Directive), amended
by Directive 98/79/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling
within the scope of this standard.
Annex ZZB
(informative)
Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EC Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling
within the scope of this standard.
__________
---------------------- Page: 8 ----------------------
SIST EN 60745-2-18:2009
IEC 60745-2-18
Edition 1.1 2008-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Hand-held motor-operated electric tools – Safety –
Part 2-18: Particular requirements for strapping tools
Outils électroportatifs à moteur – Sécurité –
Partie 2-18: Règles particulières pour les outils de cerclage
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CA
CODE PRIX
ICS 25.140.20 ISBN 2-8318-9734-3
---------------------- Page: 9 ----------------------
SIST EN 60745-2-18:2009
– 2 – 60745-2-18 © IEC:2003+A1:2008
CONTENTS
FOREWORD.3
1 Scope.5
2 Normative references.5
3 Terms and definitions .5
4 General requirements .5
5 General conditions for the tests .5
6 Void.5
7 Classification.5
8 Marking and instructions.5
9 Protection against access to live parts.5
10 Starting.6
11 Input and current .6
12 Heating.6
13 Leakage current.6
14 Moisture resistance.6
15 Electric strength.6
16 Overload protection of transformers and associated c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.