EN 60065:2002/A2:2010

Audio, video and similar electronic apparatus - Safety requirements

Incorporates FprAB (pr=21625)( CMs towards 108/395/FDIS)

Audio-, Video- und ähnliche elektronische Geräte - Sicherheitsanforderungen

Appareils audio, vidéo et appareils électroniques analogues - Exigences de sécurité

Avdio, video in sorodni elektronski aparati - Varnostne zahteve (IEC 60065:2001/A2:2010, spremenjen)

Amandma A2:2011 je dodatek k standardu SIST EN 60065:2003
1.1.1 Ta mednarodni varnostni standard velja za elektronske aparate, načrtovane tako, da se napajajo iz OMREŽJA, iz NAPAJALNE NAPRAVE, iz baterij ali iz DALJINSKEGA NAPAJANJA ter so namenjeni za sprejemanje, generiranje, snemanje ali reprodukcijo avdio, video in podobnih signalov. Prav tako velja za aparate, načrtovane za uporabo izključno v kombinaciji z zgoraj navedenimi aparati. Ta standard obravnava predvsem aparate, namenjene za gospodinjstvo ter podobno splošno uporabo, vendar se lahko uporabijo tudi na mestih javnega zborovanja, kot so šole, gledališča, molitvenih in obrednih mestih ter delovnih mestih. PROFESIONALNI APARAT, namenjen za uporabo, kot je opisana zgoraj, je prav tako zajet, razen če izrecno ne spada na področje uporabe drugega standarda. Ta standard obravnava le varnostne vidike zgoraj omenjenega aparata; ne obravnava drugih stvari, kot je stil ali zmogljivost. Ta standard velja za zgoraj omenjeni aparat, če je načrtovan za povezavo z TELEKOMUNIKACIJSKIM OMREŽJEM ali podobnim omrežjem, na primer z integriranim modemom. Nekateri primeri aparatov znotraj področja uporabe tega standarda so:
- aparat za sprejemanje in ojačevalniki za zvok in/ali sliko;
- neodvisni PRETVORNIKI OBREMENITVE in IZVORNI PRETVORNIKI;
- NAPAJALNE NAPRAVE, namenjene napajanju drugih aparatov, ki jih zajema področje uporabe tega standarda;
- ELEKTRONSKI GLASBENI INŠTRUMENTI in elektronski dodatki, kot so generator ritma, generator tona, glasbeni uglaševalci in podobni, za uporabo z inštrumenti, ki so ali niso elektronski;
- avdio in/ali video izobraževalni aparati;
- video projektorji;
- oprema za teletekst;
- predvajalniki gramofonskih plošč in zgoščenk;
- snemalniki na magnetofonski trak in zgoščenke;
- pretvorniki in ojačevalniki antenskega signala;
- priprave za pričvrstitev anten;
- CB postaje;
- aparati za SLIKOVNI MATERIAL;
- elektronski aparati s svetlobnim učinkom;
- aparati za uporabo v alarmnih sistemih;
- aparati za medsebojno komunikacijo, ki uporabljajo nizkonapetostno OMREŽJE kot medij prenosa;
- kabelski sprejemniki glavne razdelilne postaje;
- multimedijske naprave;
- profesionalni ojačevalniki, predvajalniki gramofonskih plošč ali zgoščenk, predvajalniki magnetofonskega traku in snemalniki za splošno uporabo ter sistemi za naslavljanje javnosti;  
- profesionalni zvočni/video sistemi;
- elektronski aparati z bliskovno lučjo za fotografske namene (glej Dodatek L).
1.1.2 Ta standard velja za aparate z NAZIVNO NAPETOSTJO NAPAJANJA, ki ne presega:
- 250 V izmeničnega enofaznega ali enosmernega napajanja;
- 433 V izmeničnega napajanja v primeru, da aparat za povezavo z napajanjem ni enofazni.
1.1.3 Ta mednarodni standard velja za aparate, ki se uporabljajo na višinah, ki ne presegajo 2000 m nadmorske višine, predvsem na suhih lokacijah in v regijah z zmernim ali tropskim podnebjem. V Dodatku A so podane dodatne zahteve za aparate z zaščito pred vodnim brizgom. V Dodatku B so podane dodatne zahteve za aparate za povezavo s TELEKOMUNIKACIJSKIMI OMREŽJI. Za aparate, namenjene za uporabo v vozilih, ladjah ali letalih ali pri višinah, ki presegajo 2000 m nadmorske višine, so lahko potrebne dodatne zahteve. OPOMBA: Glej Preglednico A.2 iz IEC 60664-1. Dodatne zahteve, ki niso opredeljene v tem standardu, so lahko potrebne za aparate, namenjene posebnim pogojem uporabe.
1.1.4 Pri aparatih, ki so načrtovani za napajanje iz OMREŽJA, ta standard velja za tiste, ki so namenjeni povezavi z OMREŽJEM s prehodnimi prenapetostmi, ki ne presegajo kategorije prenapetosti II v skladu z IEC 60664-1. Pri aparatih, ki so podvrženi prehodnim prenapetostim, katere presegajo kategorijo prenapetosti II, je lahko potrebna dodatna zaščita pri napajanju aparata iz OMREŽJA.

General Information

• Status: Withdrawn
• Publication Date: 07-Oct-2010
• Withdrawal Date: 30-Sep-2013
• ICS: 97.020 - Home economics in general
• Technical Committee: CLC/TC 108X - Safety of electronic equipment within the fields of Audio/Video, Information Technology and Communication Technology
• Drafting Committee: IEC/TC 108 - IEC_TC_108
• Parallel Committee: IEC/TC 108 - IEC_TC_108
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 17-Nov-2017
• Completion Date: 17-Nov-2017
• Directive: 1999/5/EC - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity
• Directive: 2001/95/EC - Directive 2001/95/EC of the European Parliament and of the Council of 3 December 2001 on general product safety
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: SIST EN 60065:2003/A2:2011 - Audio, video and similar electronic apparatus - Safety requirements (IEC 60065:2001/A2:2010, modified)

Relations

• Replaced By: EN 60065:2014 - Audio, video and similar electronic apparatus - Safety requirements
• Effective Date: 29-Jan-2023
• Amends: EN 60065:2002 - Audio, video and similar electronic apparatus - Safety requirements
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2011
Avdio, video in sorodni elektronski aparati - Varnostne zahteve (IEC
60065:2001/A2:2010, spremenjen)
Audio, video and similar electronic apparatus - Safety requirements (IEC
60065:2001/A2:2010, modified)
Audio-, Video- und ähnliche elektronische Geräte - Sicherheitsanforderungen (IEC
60065:2001/A2:2010, modifiziert)
Appareils audio, vidéo et appareils électroniques analogues - Exigences de sécurité (CEI
60065:2001/A2:2010, modifié)
Ta slovenski standard je istoveten z: EN 60065:2002/A2:2010
ICS:
33.160.01 Avdio, video in avdiovizualni Audio, video and audiovisual
sistemi na splošno systems in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60065/A2
NORME EUROPÉENNE
October 2010
EUROPÄISCHE NORM
ICS 97.020
English version
Audio, video and similar electronic apparatus -
Safety requirements
(IEC 60065:2001/A2:2010, modified)

Appareils audio, vidéo et appareils Audio-, Video- und ähnliche elektronische
électroniques analogues - Geräte -
Exigences de sécurité Sicherheitsanforderungen
(CEI 60065:2001/A2:2010, modifié) (IEC 60065:2001/A2:2010, modifiziert)

This amendment A2 modifies the European Standard EN 60065:2002; it was approved by CENELEC on
2010-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60065:2002/A2:2010 E

Foreword
The text of document 108/395/FDIS, future amendment 2 to IEC 660065:2001, prepared by IEC TC 108,
Safety of electronic equipment within the field of audio/video, information technology and communication
technology, was submitted to the IEC-CENELEC parallel vote.
A draft amendment was prepared by the Technical Committee CENELEC TC 108X, Safety of electronic
equipment within the fields of audio/video, information technology and communication technology and
was submitted to formal vote.
The combined texts were approved by CENELEC as EN 60065:2002/A2 on 2010-10-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the amendment has to be implemented

at national level by publication of an identical
(dop) 2011-10-01
national standard or by endorsement
– latest date by which the national standards conflicting
with the amendment have to be withdrawn (dow) 2013-10-01
Annexes ZA and ZB have been added by CENELEC.
__________
- 3 - EN 60065:2002/A2:2010
Endorsement notice
The text of amendment 2:2010 to the International Standard IEC 60065:2001 was approved by
CENELEC as an amendment to the European Standard with agreed common modifications as given
below.
COMMON MODIFICATIONS
In IEC 60065:2001/A2 delete all the “country” notes according to the following list:
5.3 Note
5.4.1 Note
20 Note
For special national conditions, see Annex ZB.

After 3.2 add a new clause 3.Z1:
3.Z1 To protect against excessive current, short-circuits and earth faults in MAINS, protective
devices shall be included either as integral parts of the equipment or as parts of the
building installation, subject to the following, a), b) and c):
a) except as detailed in b) and c), protective devices necessary to comply with the
requirements of 11 shall be included as parts of the equipment;
b) for components in series or parallel with the mains input to the equipment such as the
supply cord, appliance coupler, r.f.i. filter and switch, short-circuit and earth fault
protection may be provided by protective devices in the building installation;
c) it is permitted for equipment supplied via an industrial mains plug or for
PERMANENTLY CONNECTED APPARATUS, to rely on dedicated over current and
short-circuit protection in the building installation, provided that the means of
protection, e.g. fuses or circuit breakers, is fully specified in the installation
instructions.
If reliance is placed on protection in the building installation, the installation instructions
shall so state, except that for not via an industrial mains plug or for PERMANENTLY
CONNECTED APPARATUS the building installation shall be regarded as providing
protection in accordance with the rating of the wall socket outlet.

5.1 i) in EN 60065:2002 and EN 60065:2002/A1:2006:
Withdraw the common modification for both standards.
Rationale: The relevant text is now part of IEC 60065:2001/A2, Subclause 5.1 item h).

Bibliography in IEC 60065:2001/A2:200X (108/395/FDIS)

Add the following notes for the standards indicated:

IEC 60695 series NOTE Harmonized in EN 60695 series.
IEC 62087 NOTE Harmonized as EN 62087.

Replace the whole Annex ZA by the following:

NOTE  The changes related to EN 60065:2002/A11:2008 are indicated in red.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Date Title EN/HD Date

1)
- - Audio, video and similar electronic EN 50333 2001
apparatus – Routine electrical
safety testing in production
- - Insulating, sheathing and covering EN 50363 series
materials for low-voltage energy
cables
- - Electrical test methods for low EN 50395 2005
voltage energy cables
- - Non electrical test methods for low EN 50396 2005
voltage energy cables
IEC 60027 series Letter symbols to be used in EN/HD 60027 series
electrical technology
IEC 60038 2002 IEC standard voltages - -

IEC 60068-2-6 1995 Environmental testing
2)
+ corr. March 1995 Part 2: Tests – Test Fc: Vibration EN 60068-2-6 1995
(sinusoidal)
3)
IEC 60068-2-32 1975 Environmental testing EN 60068-2-32 1993
Part 2: Tests – Test Ed: Free fall

IEC 60068-2-31 2008 Environmental testing EN 60068-2-31 2008
Part 2-31: Tests – Test Ec: Rough
handling shocks, primarily for
equipment-type specimensl
———————
1)
Will be superseded by EN 50514:2008 “Audio, video and information technology equipment - Routine electrical safety testing in
production” on 2011-07-01.
2)
Will be superseded by EN 60068-2-6:2008 “Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)” on
2011-02-01.
3)
EN 60068-2-32 includes A2:1990 to IEC 60068-2-32:1975 (IEC/EN 60068-2-32 has been replaced by
IEC/EN 60068-2-31:2008).
- 5 - EN 60065:2002/A2:2010
Publication Date Title EN/HD Date

IEC 60068-2-75 1997 Environmental testing EN 60068-2-75 1997
Part 2-75: Tests - Test Eh:
Hammer tests
IEC 60068-2-78 2001 Environmental testing EN 60068-2-78 2001
Part 2-78: Tests - Test Cab: Damp
heat, steady state
4)
IEC 60085 2004 Thermal evaluation and EN 60085 2004
classification of electrical insulation

5)
IEC 60086-4 2000 Primary batteries EN 60086-4 2000
Part 4: Safety of lithium batteries

IEC 60107-1 1997 Methods of measurement on EN 60107-1 1997
receivers for television broadcast
transmissions -
Part 1: General considerations -
Measurements at radio and video
frequencies
IEC 60112 2003 Method for the determination of the EN 60112 2003
proof and the comparative tracking
indices of solid insulating materials

IEC 60127 series Miniature fuses EN 60127 series

IEC 60167 1964 Methods of test for the HD 568 S1 1990
determination of the insulation
resistance of solid insulating
materials
IEC 60216 series Electrical insulating materials - EN 60216 series
Thermal endurance properties
6)
IEC 60227 series Polyvinyl chloride insulated cables HD 21 series
of rated voltages up to and
including 450/750 V
7)
IEC 60245 series Rubber insulated cables – Rated HD 22 series
voltages up to and including
450/750 V
IEC 60249-2 series Base materials for printed circuits EN 60249-2 series
Part 2: Specifications
8)
IEC 60268-1 1985 Sound system equipment HD 483.1 S2 1989
Part 1: General
———————
4)
Will be superseded by EN 60085:2008 “Electrical insulation - Thermal evaluation and designation” on 2010-12-01.
5)
Will be superseded by EN 60086-4:2007 “Primary batteries -- Part 4: Safety of lithium batteries” on 2010-11-01.
6)
The HD 21 series, which is related to, but not directly equivalent with the IEC 60227 series. Also EN 50363, EN 50395 and
EN 396 are to be taken into account.
7)
The HD 22 series, which is related to, but not directly equivalent with the IEC 60245 series. Also EN 50363, EN 50395 and
EN 396 are to be taken into account.
8)
HD 483.1 S2:1989 includes A1:1988 to IEC 60268-1:1985.

Publication Date Title EN/HD Date

IEC 60317 series Specifications for particular types EN 60317 series
of winding wires
IEC 60320 series Appliance couplers for household EN 60320 series
and similar general purposes
IEC 60335-1 (mod) 2001 Safety of household and similar EN 60335-1 2002
A1 2004 electrical appliances A1 2004
A2 + Corr. August 2006 Part 1: General requirements A2 2006
+ A11 2004
+ A12 2006
+ A13 2008
IEC 60384-1 (mod) 1999 Fixed capacitors for use in EN 60384-1 2001
electronic equipment
Part 1: Generic specification
IEC 60384-14 2005 Fixed capacitors for use in EN 60384-14 2005
electronic equipment
Part 14: Sectional specification:
Fixed capacitors for
electromagnetic interference
suppression and connection to the
supply mains
IEC 60417 database Graphical symbols for use on - -
equipment
IEC 60454 series Pressure-sensitive adhesive tapes EN 60454 series
for electrical purposes
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code) + corr. May 1993
A1 1999 A1 2000
IEC 60664-1 2007 Insulation coordination for EN 60664-1 2007
equipment within low-voltage
systems
Part 1: Principles, requirements
and tests
IEC 60664-3 2003 Insulation coordination for EN 60664-3 2003
equipment within low-voltage
systems
Part 3: Part 3: Use of coating,
potting or moulding for protection
against pollution
IEC 60691 2002 Thermal links – Requirements and EN 60691 2003
A1 2006 application guide A1 2007

IEC 60695-11-5 2004 Fire hazard testing EN 60695-11-5 2005
Part 11-5: Test flames - Needle-
flame test method – Apparatus,
confirmatory test arrangement and
guidance
- 7 - EN 60065:2002/A2:2010
Publication Date Title EN/HD Date

IEC 60695-11-10 1999 Fire hazard testing EN 60695-11-10 1999
A1 2003 Part 11-10: Test flames – 50 W A1 2003
horizontal and vertical flame test
methods
IEC 60695-11-20 1999 Fire hazard testing EN 60695-11-20 1999
A1 2003 Part 11-20: Test flames - 500 W A1 2003
flame test methods
IEC 60730 (mod) series Automatic electrical controls for EN 60730 series
household and similar use
9)
IEC 60747-5-5 2007 Semiconductor devices - Discrete EN 60747-5-5 201X
devices -
Part 5-5: Optoelectronic devices -
Photocouplers
IEC 60825-1 2007 Safety of laser products EN 60825-1 2007
Part 1: Equipment classification
and requirements
IEC 60851 series Winding wires – Test methods EN 60851 series

IEC 60884 series Plugs and socket-outlets for - -
household and similar purposes

IEC 60885-1 1987 Electrical test methods for electric - -
cables
Part 1: Electrical tests for cables,
cords and wires for voltages up to
and including 450/750 V
IEC 60906 series IEC system of plugs and socket-- -
outlets for household and similar
purposes
IEC 60950-1 (mod) 2005 Safety of information technology EN 60950-1 2006
equipment + A11 2009
Part 1: General requirements
IEC 60990 1999 Methods of measurement of touch- EN 60990 1999
current and protective conductor
current
IEC 60998-2-2 2002 Connecting devices for low-voltage EN 60998-2-2 2004
(mod) circuits for household and similar
purposes
Part 2-2: Particular requirements
for connecting devices as separate
entities with screwless-type
clamping units
———————
9)
At draft stage.
Publication Date Title EN/HD Date

IEC 60999-1 1999 Connecting devices – Safety EN 60999-1 2000
requirements for screw-type and
screwless-type clamping units
Part 1: General requirements and
particular requirements for
clamping units for conductors from
2 2
0,2 mm up to 35 mm (included)
IEC 61032 1997 Protection of persons and EN 61032 1998
equipment by enclosures – Pro
...