HD 22.13 S2:2007
(Main)Cables of rated voltages up to and including 450/750 V and having cross-linked insulation - Part 13: Halogen-free flexible cables having low emission of smoke
Cables of rated voltages up to and including 450/750 V and having cross-linked insulation - Part 13: Halogen-free flexible cables having low emission of smoke
This part (Part 13) of the HD details the particular specifications for single and multicore halogen-free flexible cables of rated voltage 450/750 V, insulated and sheathed with cross-linked compound, and having low emission of smoke. Each cable shall comply with the appropriate requirements given in Part 1 of this HD and the particular requirements of this part. NOTE The overall dimensions of the cables in this part of HD 22 have been calculated in accordance with EN 60719.
Starkstromleitungen mit vernetzter Isolierhülle für Nennspannungen bis 450/750 V - Teil 13: Halogenfreie flexible Leitungen mit geringer Entwicklung von Rauch
Dieser Teil 13 des HD enthält die besonderen Bestimmungen für ein-, mehr- und vieladrige halogenfreie Schlauchleitungen mit Nennspannungen bis 450/750 V, mit Isolierhülle und Mantel aus vernetztem Polymer, mit geringer Entwicklung von Rauch und korrosiven Gasen im Brandfall Alle Leitungen müssen mit den in Teil 1 von diesem HD angegebenen Anforderungen und den besonderen Anforderungen dieses Teils übereinstimmen. ANMERKUNG Die Außenmaße der Leitungen nach diesem Teil des HD 22 sind in Überein¬stimmung mit EN 60719 errechnet worden.
Conducteurs et câbles isolés avec des matériaux réticulés de tension assignée au plus égale à 450/750 V - Partie 13: Câbles souples à faible émission de fumées
La présente partie (Partie 13) du HD précise les spécifications particulières applicables aux câbles monoconducteurs et multiconducteurs souples sans halogène, de tension assignée 450/750 V, et ayant une faible émission de fumée. Chaque câble doit répondre aux prescriptions appropriées données dans la Partie 1 de ce HD et aux prescriptions particulières de la présente partie. NOTE Les dimensions extérieures des câbles de la présente partie du HD 22 ont été calculées conformément à la EN 60719.
Kabli z omreženo izolacijo za naznačene napetosti do vključno 450/750 V - 13. del: Zvijavi kabli brez halogenov z nizko emisijo dima
Označuje posebno specifikacijo za eno- in večžilne zvijave kable brez halogenov, naznačene napetosti 450/750 V, izolirane in oplaščene z omreženo izolacijo, z nizko emisijo dima.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2007
1DGRPHãþD
SIST HD 22.13 S1:1998
SIST HD 22.13 S1:1998/A1:2000
.DEOL]RPUHåHQRL]RODFLMR]DQD]QDþHQHQDSHWRVWLGRYNOMXþQR9GHO
=YLMDYLNDEOLEUH]KDORJHQRY]QL]NRHPLVLMRGLPD
Cables of rated voltages up to and including 450/750 V and having cross-linked
insulation -- Part 13: Halogen-free flexible cables having low emission of smoke
Starkstromleitungen mit vernetzter Isolierhülle für Nennspannungen bis 450/750 V - Teil
13: Halogenfreie flexible Leitungen mit geringer Entwicklung von Rauch
Conducteurs et câbles isolés avec des matériaux réticulés de tension assignée au plus
égale a 450/750 V - Partie 13: Câbles souples a faible émission de fumées
Ta slovenski standard je istoveten z: HD 22.13 S2:2007
ICS:
29.060.20 Kabli Cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
HARMONIZATION DOCUMENT
HD 22.13 S2
DOCUMENT D'HARMONISATION
February 2007
HARMONISIERUNGSDOKUMENT
ICS 29.060.20 Supersedes HD 22.13 S1:1996 + A1:2000
English version
Cables of rated voltages up to and including 450/750 V
and having cross-linked insulation -
Part 13: Halogen-free flexible cables having low emission of smoke
Conducteurs et câbles isolés avec Starkstromleitungen mit vernetzter
des matériaux réticulés de tension Isolierhülle für Nennspannungen
assignée au plus égale à 450/750 V - bis 450/750 V -
Partie 13: Câbles souples Teil 13: Halogenfreie flexible Leitungen
à faible émission de fumées mit geringer Entwicklung von Rauch
This Harmonization Document was approved by CENELEC on 2006-12-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for implementation of this
Harmonization Document at national level.
Up-to-date lists and bibliographical references concerning such national implementations may be obtained on
application to the Central Secretariat or to any CENELEC member.
This Harmonization Document exists in three official versions (English, French, German).
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. HD 22.13 S2:2007 E
Foreword
This Harmonization Document was prepared by the Technical Committee CENELEC TC 20, Electric
cables.
The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC
as HD 22.13 S2 on 2006-12-01.
This Harmonization Document supersedes HD 22.13 S1:1996 + A1:2000.
The following dates were fixed:
– latest date by which the existence of the HD
(doa) 2007-06-01
has to be announced at national level
– latest date by which the HD has to be implemented
at national level by publication of a harmonized
national standard or by endorsement (dop) 2007-12-01
– latest date by which the national standards conflicting
with the HD have to be withdrawn (dow) 2008-12-01
HD 22, Cables of rated voltages up to and including 450/750 V and having cross-linked insulation, now
has the following parts:
HD 22.1 S4 General requirements
1)
HD 22.2 S3 Test methods
HD 22.3 S4 Heat resistant silicone rubber insulated cables
HD 22.4 S4 Cords and flexible cables
HD 22.5 (Spare)
HD 22.6 S2 Arc welding cables
HD 22.7 S2 Cables with increased heat resistance for internal wiring for a conductor
temperature of 110°C
HD 22.8 S2 Polychloroprene or equivalent synthetic elastomer sheathed cable for decorative
chains
HD 22.9 S3 Single core halogen-free non-sheathed cables for fixed wiring having low emission
of smoke
HD 22.10 S2 EPR insulated and polyurethane sheathed flexible cables
HD 22.11 S2 EVA cords and flexible cables
HD 22.12 S2 Heat resistant EPR cords and flexible cables
HD 22.13 S2 Halogen-free flexible cables having low emission of smoke
HD 22.14 S3 Cords for applications requiring high flexibility
HD 22.15 S2 Multicore cables insulated and sheathed with heat resistant silicone rubber
HD 22.16 S2 Water resistant polychloroprene or equivalent synthetic elastomer sheathed cables
1)
HD 22.2 has been superseded by EN 50395 and EN 50396
- 3 - HD 22.13 S2:2007
Contents
Page
1 Scope.4
2 Normative references.4
3 Cables with one to five cores.5
3.1 Code designation .5
3.2 Rated voltage .5
3.3 Construction .5
3.4 Tests .6
3.5 Smoke emission of cable .6
3.6 Guide to use (informative).6
4 Cables with more than five cores (multicore cables).11
4.1 Code designation .11
4.2 Rated Voltage .11
4.3 Construction .11
4.4 Tests .12
4.5 Smoke emission of cable .12
4.6 Guide to use (informative).12
Annex A (normative) Requirements for compatibility test .15
Annex B (normative) Requirements for halogens.16
Annex C (normative) Determination of halogens – Elemental test .18
Bibliography.20
Tables
Table 1 – Dimensions of Type H07ZZ-F .7
Table 2 – Tests for Type H07ZZ-F .10
Table 3 – Dimensions of Type H07ZZ-F .13
Table 4 – Tests for Type H07ZZ-F .14
Table A.1 – Requirements.15
Table B.1 – Test method, measurement, requirements.16
Table B.2 – Sequential test programme.17
1 Scope
This part (Part 13) of the HD details the particular specifications for single and multicore halogen-free
flexible cables of rated voltage 450/750 V, insulated and sheathed with cross-linked compound, and
having low emission of smoke.
Each cable shall comply with the appropriate requirements given in Part 1 of this HD and the particular
requirements of this part.
NOTE The overall dimensions of the cables in this part of HD 22 have been calculated in accordance with EN 60719.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 50266-2-4 Common test methods for cables under fire conditions – Test for vertical flame
spread of vertically-mounted bunched wires or cables –
Part 2-4: Procedures – Category C
EN 50267-2-1 Common test methods for cables under fire conditions – Tests on gases evolved
during combustion of material from cables –
Part 2-1: Procedures – Determination of the amount of halogen acid gas
EN 50267-2-2 Common test methods for cables under fire conditions – Tests on gases evolved
during combustion of materials from cables –
Part 2-2: Procedures – Determination of degree of acidity of gases for materials by
measuring pH and conductivity
EN 50334 Marking by inscription for the identification of cores of electric cables
EN 50363-5 Insulating, sheathing and covering materials for low voltage energy cables –
Part 5: Halogen-free, cross-linked insulating compounds
EN 50363-6 Insulating, sheathing and covering materials for low voltage energy cables –
Part 6: Halogen-free, cross-linked sheathing compounds
EN 50395 Electrical test methods for low voltage energy cables
EN 50396 Non electrical test methods for low voltage energy cables
EN 60228 Conductors of insulated cables (IEC 60228)
EN 60332-1-2 Tests on electric and optical fibre cables under fire conditions –
Part 1-2: Test for vertical flame propagation for a single insulated wire or cable –
Procedure for 1 kW pre-mixed flame (IEC 60332-1-2)
EN 60684-2 Flexible insulating sleeving – Part 2: Methods of test (IEC 60684-2)
EN 60811 (series) Insulating and sheathing materials of electric and optical fibre cables – Common
test methods (IEC 60811 series)
EN 61034-2 Measurement of smoke density of cables burning under defined conditions –
Part 2: Test procedure and requirements (IEC 61034-2)
- 5 - HD 22.13 S2:2007
3 Cables with one to five cores
3.1 Code designation
H07ZZ-F
3.2 Rated voltage
450/750 V
NOTE 600/1 000 V when this cable is used in fixed installations (see HD 516).
3.3 Construction
3.3.1 Conductor
Number of conductors : 1, 2, 3, 4 or 5.
The conductors shall comply with the requirements given in EN 60228 for Class 5 conductors. The wires
may be plain or tinned.
3.3.2 Separator
A separator of suitable material may be applied around each conductor.
3.3.3 Insulation
The insulation shall be a cross-linked compound, Type EI 8 to EN 50363-5, applied around each
conductor
The insulation shall be applied by extrusion. It may consist of one or two layers. All tests shall be applied
to the complete insulation, which must meet the requirements for Type EI 8.
The insulation thickness shall comply with the specified value given in Table 1, column 2.
The insulation resistance shall not be less than the value given in Table 1, column 8.
3.3.4 Assembly of cores and filler, if any
The cores of cables having two to five cores shall be twisted together.
A centre filler may be used.
In the case of cores having conductors of large cross-section a textile tape may be applied around the
core assembly before application of the sheath, provided that the finished cables shall not have any
substantial cavity in the outer interstices between the cores.
3.3.5 Sheath
The cores shall be covered with a sheath.
(a) For cables with a specified sheath thickness up to and including 2,4 mm
– sheath in a single layer, cross-linked compound of type EM 8 to EN 50363-6.
(b) For cables with a specified sheath thickness greater than 2,4 mm
– sheath either in a single layer, cross-linked compound of type EM 8 to EN 50363-6
– or in two layers, with the inner layer made of one of the cross-linked compounds type EM 8 or
EM 10 to EN 50363-6 and the outer layer of the cross-linked compound type EM 8 to
EN 50363-6.
The thickness of sheath shall comply with the specified value given in Table 1, columns 3, 4 and 5.
The sheath applied in a single layer or the inner layer of the sheath in two layers shall, for cables with 2 to
5 cores, fill the spaces between the cores.
The sheath shall be capable of being removed without damage to the core(s).
For non-electrical tests on sheaths in two layers see Part 1, Subclause 5.5.2.2.
3.3.6 Overall diameter
The mean overall diameter shall be within the limits given in Table 1, columns 6 and 7.
3.3.7 Outer marking
The cable shall have the marking H07ZZ-F printed or embossed on, or indented into, the outer surface of
the sheath. The marking, which shall meet the requirements of Subclauses 3.2 and 3.3 of Part 1, shall be
legible.
3.4 Tests
Compliance with the requirements of Subclause 3.3 shall be checked by inspection and by the tests given
in Table 2.
The requirements to be met for the compatibility test shall be as given in Annex A.
3.5 Smoke emission of cable
When tested in accordance with the method and procedure given in EN 61034-2, all sizes of cable shall
exceed 60 % light transmittance througho
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.