EN IEC 60684-3-214:2019
(Main)Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall
IEC 60684-3-214:2019 is available as IEC 60684-3-214:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 15-60684-3-214:2019 gives the requirements for two types of heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall with a nominal shrink ratio of 3:1. This sleeving has been found suitable for use at temperatures of up to 100 °C. - Type A: Medium wall - internal diameter up to 200 mm typically. - Type B: Thick wall - internal diameter up to 200 mm typically. These sleevings are normally supplied in colour black. Since these types of sleeving cover a significantly large range of sizes and wall thicknesses, Annex A (Tables A.1 and A.2) of this document provides a guide to the range of sizes available. The actual size will be agreed between the user and supplier. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This fourth edition cancels and replaces the third edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: - removal of colour fastness to light test, as this is covered by the test for carbon black content. Keywords: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 214: Polyolefin-Wärmeschrumpfschläuche, nicht-flammwidrig, dickwandig und mittlere Wanddicke
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 214: Gaines thermorétractables en polyoléfine, non ignifugées, à paroi épaisse et moyenne
IEC 60684-3-214:2019 est disponible sous forme de IEC 60684-3-214:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente. L'IEC 60684-3-214:2019 donne les exigences relatives à deux types de gaines thermorétractables, en polyoléfine, non ignifugées, à paroi épaisse et moyenne, dont le rapport de rétreint nominal est 3:1. Ces gaines se sont avérées appropriées pour une utilisation à des températures allant jusqu’à 100 °C. - Type A: Paroi moyenne - diamètre intérieur généralement jusqu’à 200 mm. - Type B: Paroi épaisse - diamètre intérieur généralement jusqu’à 200 mm. La couleur de ces gaines est normalement le noir. Comme ces types de gaines couvrent une plage très étendue de tailles et d’épaisseurs de paroi, l'Annexe A (Tableaux A.1 et A.2) du présent document fournit un guide des tailles disponibles dans cette plage. La taille réelle fait l’objet d’un accord entre l’utilisateur et le fournisseur. Les matériaux conformes à la présente spécification satisfont à des niveaux de performances établis. Cependant, le choix d’un matériau par un utilisateur, pour une application spécifique, est fondé sur les exigences réelles nécessaires pour obtenir une performance adéquate pour l'application concernée, et n'est pas fondé sur cette seule spécification. Cette quatrième édition annule et remplace la troisième édition parue en 2013. Cette édition constitue une révision technique. Cette édition inclut la modification technique majeure suivante par rapport à l’édition précédente: - suppression de l'essai de solidité de la couleur à la lumière, cet essai étant couvert par l'essai de détermination de la teneur en noir de carbone. Mots-clés : Gaines thermorétractables en polyoléfine, non ignifugées, à paroi épaisse et moyenne.
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 214. list: Toplotno skrčljive poliolefinske cevi, neognjevarne, debela in srednje debela stena (IEC 60684-3-214:2019)
Ta dokument podaja zahteve za dva tipa toplotno skrčljivih poliolefinskih cevi, neognjevarnih, debela in srednje debela stena, z nazivnimi razmerji krčenja do 3:1. Te cevi so primerne za uporabo pri temperaturi do 100 °C.
• Tip A: srednje debela stena – notranji premer običajno do 200 mm. • Tip B: debela stena – notranji premer običajno do 200 mm. Te cevi so običajno dobavljive v črni barvi. Ker ta tipa cevi zajemata bistveno velik razpon velikosti in debelin sten, so v preglednicah A.1 in A.2 v dodatku A tega dokumenta podana navodila glede razpona razpoložljivih velikosti. O dejanski velikosti se dogovorita uporabnik in dobavitelj. Materiali, ki so skladni s to specifikacijo, ustrezajo določenim ravnem delovanja. Vendar uporabnik bo material za določeno uporabo izbral glede na dejanske zahteve, ki omogočajo ustrezno delovanje pri tej uporabi, in ne samo na podlagi te specifikacije.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60684-3-214:2019
01-december-2019
Nadomešča:
SIST EN 60684-3-214:2014
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 214. list:
Toplotno skrčljive poliolefinske cevi, neognjevarne, debela in srednje debela stena
(IEC 60684-3-214:2019)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet
214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall (IEC
60684-3-214:2019)
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 214:
Polyolefin-Wärmeschrumpfschläuche, nicht-flammwidrig, dickwandig und mittlere
Wanddicke (IEC 60684-3-214:2019)
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuille 214: Gaines thermorétractables en polyoléfine, non ignifugées, à paroi épaisse et
moyenne (IEC 60684-3-214:2019)
Ta slovenski standard je istoveten z: EN IEC 60684-3-214:2019
ICS:
29.035.20 Plastični in gumeni izolacijski Plastics and rubber insulating
materiali materials
SIST EN IEC 60684-3-214:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60684-3-214:2019
---------------------- Page: 2 ----------------------
SIST EN IEC 60684-3-214:2019
EUROPEAN STANDARD EN IEC 60684-3-214
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2019
ICS 29.035.20 Supersedes EN 60684-3-214:2014 and all of its
amendments and corrigenda (if any)
English Version
Flexible insulating sleeving - Part 3: Specifications for individual
types of sleeving - Sheet 214: Heat-shrinkable, polyolefin
sleeving, not flame retarded, thick and medium wall
(IEC 60684-3-214:2019)
Gaines isolantes souples - Partie 3: Spécifications pour Isolierschläuche - Teil 3: Anforderungen für einzelne
types particuliers de gaines - Feuille 214: Gaines Schlauchtypen - Blatt 214: Polyolefin-
thermorétractables en polyoléfine, non ignifugées, à paroi Wärmeschrumpfschläuche, nicht-flammwidrig, dickwandig
épaisse et moyenne und mittlere Wanddicke
(IEC 60684-3-214:2019) (IEC 60684-3-214:2019)
This European Standard was approved by CENELEC on 2019-09-12. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60684-3-214:2019 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60684-3-214:2019
EN IEC 60684-3-214:2019 (E)
European foreword
The text of document 15/889/FDIS, future edition 4 of IEC 60684-3-214, prepared by IEC/TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60684-3-214:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-06-12
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-09-12
document have to be withdrawn
This document supersedes EN 60684-3-214:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60684-3-214:2019 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added f
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.