EN 50632-2-14:2016

Electric motor-operated tools - Dust measurement procedure - Part 2-14: Particular requirements for planers

This European Standard applies to hand-held motor-operated electric tools and deals with the measurement procedure for planers for measurements of dust emission.

Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-14: Besondere Anforderungen für Hobel

Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-14: Exigences particulières pour les raboteuses

L'article de la Partie 1 est applicable avec l'exception suivante: Addition: La présente partie de l'EN 50632 s'applique aux raboteuses.

Elektromotorna orodja - Postopek merjenja prahu - 2-14. del: Posebne zahteve za poravnalne skobeljnike

Ta evropski standard se uporablja za ročna elektromotorna orodja in obravnava postopek merjenja za poravnalne skobeljnike za izvajanje meritev emisije prahu.

General Information

• Status: Published
• Publication Date: 21-Jul-2016
• ICS: 13.040.40 - Stationary source emissions
• ICS: 25.140.20 - Electric tools
• Technical Committee: CLC/TC 116 - Safety of hand-held motor-operated electric tools
• Drafting Committee: CLC/TC 116 - Safety of hand-held motor-operated electric tools
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 02-Jun-2021
• Ref Project: SIST EN 50632-2-14:2016 - Electric motor-operated tools - Dust measurement procedure - Part 2-14: Particular requirements for planers

Relations

• Amended By: EN 50632-2-14:2016/A1:2021 - Electric motor-operated tools - Dust measurement procedure - Part 2-14: Particular requirements for planers
• Effective Date: 08-Sep-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2016
Elektromotorna orodja - Postopek merjenja prahu - 2-14. del: Posebne zahteve za
poravnalne skobeljnike
Electric motor-operated tools - Dust measurement procedure - Part 2-14: Particular
requirements for planers
Ta slovenski standard je istoveten z: EN 50632-2-14:2016
ICS:
25.100.25 Orodja za glajenje in Tools for planing and
ravnalna orodja broaching machines
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-2-14

NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2016
ICS 13.040.40; 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-14: Particular requirements for planers
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-14: Exigences particulières pour les Teil 2-14: Besondere Anforderungen für Hobel
raboteuses
This European Standard was approved by CENELEC on 2016-05-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-14:2016 E
Contents
European foreword . 3
1 Scope . 4
2 Normative references. 4
3 Terms and definitions . 4
4 Test procedure . 4
5 Instrumentation . 5
6 Information to be reported . 5
Tables
Table 101 – Operating conditions for planers intended to cut wood . 5
European foreword
This document (EN 50632-2-14:2016) has been prepared by CLC/TC 116 "Safety of motor-oper
...