iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61788-5:2001

(Main)

Superconductivity - Part 5: Matrix to superconductor volume ratio measurement - Copper to superconductor volume ratio of Cu/Nb-Ti composite superconductors

Superconductivity - Part 5: Matrix to superconductor volume ratio measurement - Copper to superconductor volume ratio of Cu/Nb-Ti composite superconductors

Covers a test method for the determination of copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wire. The Cu/Nb-Ti composite test conductor discussed in this method has a monolithic structure with a round or rectangular cross-section. This test method is carried out by dissolving the copper with nitric acid. Deviations from this test method that are allowed for routine tests and other specific restrictions are given in this standard.

Supraleitfähigkeit - Teil 5: Messung des Verhältnisses von Matrixvolumen zu Supraleitervolumen - Verhältnis von Kupfervolumen zu Supraleitervolumen von Cu/Nb Ti-Verbundsupraleitern

Supraconductivité - Partie 5: Mesure du rapport volumique matrice/supraconducteurs - Rapport volumique cuivre/supraconducteur des composites supraconducteurs de Cu/Nb-Ti

Superconductivity - Part 5: Matrix to superconductor volume ratio measurement - Copper to superconductor volume ratio of Cu/Nb-Ti composite superconductors

General Information

Status
Withdrawn
Publication Date
02-Apr-2001
Withdrawal Date
30-Nov-2003
ICS
29.050 - Superconductivity and conducting materials
Technical Committee
CLC/SR 90 - Superconductivity
Drafting Committee
IEC/TC 90 - IEC_TC_90
Parallel Committee
IEC/TC 90 - IEC_TC_90
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
02-Jul-2016
Completion Date
02-Jul-2016
Ref Project
SIST EN 61788-5:2002 - Superconductivity -- Part 5: Matrix to superconductor volume ratio measurement - Copper to superconductor volume ratio of Cu/Nb-Ti composite superconductors

Relations

Replaced By
EN 61788-5:2013 - Superconductivity - Part 5: Matrix to superconductor volume ratio measurement - Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires
Effective Date
29-Jan-2023

Buy Standard

EN 61788-5:2002EN 61788-5:2002
PreviousNext
Standard
EN 61788-5:2002
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61788-23:2024(Main)
Superconductivity - Part 23: Residual resistance ratio measurement - Residual resistance ratio of cavity-grade Nb superconductors
SIST EN IEC 61788-23:2024

IEC 61788-23:2024 is available as IEC 61788-23:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-23:2024 addresses a test method for the determination of the residual resistance ratio (RRR), rRRR, of cavity-grade niobium. This method is intended for high-purity niobium grades with 150 < rRRR < 600. The test method is valid for specimens with rectangular or round cross-section, cross-sectional area greater than 1 mm2 but less than 20 mm2, and a length not less than 10 nor more than 25 times the width or diameter.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-22-3:2022(Main)
Superconductivity - Part 22-3: Superconducting strip photon detector - Dark count rate
SIST EN IEC 61788-22-3:2022

IEC 61788-22-3:2022 is applicable to the measurement of the dark count rate (DCR, RD) of superconductor strip photon detectors (SSPDs). It specifies terms, definitions, symbols and the measurement method of DCR that depends on the bias current (Ib) and operating temperature (T). NOTE The data of measurement results in Annex A are based on measurements of one institute only. The standard will be updated after the data of a complete round robin test are available.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-22-2:2021(Main)
Superconductivity - Part 22-2: Normal state resistance and critical current measurement - High-Tc Josephson junction
SIST EN IEC 61788-22-2:2022

This part of IEC 61788 is applicable to high-Tc Josephson junctions. It specifies terms, definitions, symbols and the measurement and estimation method for normal state resistance (Rn) and intrinsic critical current (Ici), based on a combination of selecting a data set from measured U-I curves with a geometric mean criterion and fitting a hyperbolic function to that data set.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-23:2021(Main)
Superconductivity - Part 23: Residual resistance ratio measurement - Residual resistance ratio of cavity-grade Nb superconductors
SIST EN IEC 61788-23:2021

This part of IEC 61788 addresses a test method for the determination of the residual resistance ratio (RRR), rRRR, of cavity-grade niobium. This method is intended for high-purity niobium grades with 150 < rRRR < 600. The test method is valid for specimens with rectangular or round cross-section, cross-sectional area greater than 1 mm2 but less than 20 mm2, and a length not less than 10 nor more than 25 times the width or diameter.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-17:2021(Main)
Superconductivity - Part 17: Electronic characteristic measurements - Local critical current density and its distribution in large-area superconducting films
SIST EN IEC 61788-17:2021

IEC 61788-17:2021 is available as IEC 61788-17:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-17:2021 specifies the measurements of the local critical current density (Jc) and its distribution in large-area high-temperature superconducting (HTS) films by an inductive method using third-harmonic voltages. The most important consideration for precise measurements is to determine Jc at liquid nitrogen temperatures by an electric-field criterion and obtain current-voltage characteristics from its frequency dependence. Although it is possible to measure Jc in applied DC magnetic fields [20] [21], the scope of this document is limited to the measurement without DC magnetic fields. This technique intrinsically measures the critical sheet current that is the product of Jc and the film thickness d. The range and measurement resolution for Jcd of HTS films are as follows. - Jcd: from 200 A/m to 32 kA/m (based on results, not limitation). - Measurement resolution: 100 A/m (based on results, not limitation).

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-26:2020(Main)
Superconductivity - Part 26: Critical current measurement - DC critical current of RE-Ba-Cu-O composite superconductors
SIST EN IEC 61788-26:2020

IEC 61788-26:2020 specifies a test method for determining the DC critical current of short RE (rare earth)-Ba-Cu-O (REBCO) composite superconductor specimens that have a shape of straight flat tape. This document applies to test specimens shorter than 300 mm and having a rectangular cross section with an area of 0,03 mm2 to 7,2 mm2, which corresponds to tapes with width ranging from 1,0 mm to 12,0 mm and thickness from 0,03 mm to 0,6 mm. This method is intended for use with superconductor specimens that have critical current less than 300 A and n-values larger than 5 under standard test conditions: the test specimen is immersed in liquid nitrogen bath at ambient pressure without external magnetic field during the testing. Deviations from this test method that are allowed for routine tests and other specific restrictions are given in this document.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-4:2020(Main)
Superconductivity - Part 4: Residual resistance ratio measurement - Residual resistance ratio of Nb-Ti and Nb3Sn composite superconductors
SIST EN IEC 61788-4:2020

IEC 61788-4:2020 is available as IEC 61788-4:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-4:2020 specifies a test method for the determination of the residual resistance ratio (RRR) of Nb-Ti and Nb3Sn composite superconductors with Cu, Cu-Ni, Cu/Cu-Ni and Al matrix in a strain-free condition and zero external magnetic field. This method is intended for use with superconductor specimens that have a monolithic structure with rectangular or round cross-section, RRR value less than 350, and cross-sectional area less than 3 mm2. In the case of Nb3Sn, the specimens have received a reaction heat-treatment. This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) change in the suitable distance of voltage taps on the specimen for reliable measurement, b) new report on the result of the round robin test of the residual resistance ratio of Nb3Sn superconductors that proves the validity of the measurement method in this standard, c) revision of the confusing definitions of the copper ratio and copper fraction.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-7:2020(Main)
Superconductivity - Part 7: Electronic characteristic measurements - Surface resistance of high-temperature superconductors at microwave frequencies
SIST EN IEC 61788-7:2020

IEC 61788-7:2020 is available as IEC 61788-7:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-7:2020 describes measurement of the surface resistance (Rs) of superconductors at microwave frequencies by the standard two-resonator method. The object of measurement is the temperature dependence of Rs at the resonant frequency. The applicable measurement range of Rs for this method is as follows: - Frequency: 8 GHz < f < 30 GHz - Measurement resolution: 0,01 m Ω at 10 GHz The Rs data at the measured frequency, and that scaled to 10 GHz, assuming the f 2 rule for comparison, is reported. This third edition cancels and replaces the second edition, published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) informative Annex B, relative combined standard uncertainty for surface resistance measurement has been added; b) precision and accuracy statements have been converted to uncertainty; c) reproducibility in surface resistant measurement has been added.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-25:2018(Main)
Superconductivity - Part 25: Mechanical properties measurement - Room temperature tensile test on REBCO wires
SIST EN IEC 61788-25:2019

IEC 61788-25:2018 specifies the test method and procedures for testing tensile mechanical properties of REBCO superconductive composite tapes at room temperature. This test is used to measure the modulus of elasticity and 0,2 % proof strength. The values for elastic limit, fracture strength and percentage elongation after fracture serve only as a reference. This document applies to samples having a rectangular cross-section with an area of 0,12 mm2 to 6,0 mm2 (corresponding to the tapes with width of 2,0 mm to 12,0 mm and thickness of 0,06 mm to 0,5 mm)

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61788-23:2018(Main)
Superconductivity - Part 23: Residual resistance ratio measurement - Residual resistance ratio of Nb superconductors
SIST EN IEC 61788-23:2018

IEC 61788-23:2018 addresses a test method for the determination of the residual resistance ratio (RRR) of cavity-grade niobium. The test method should be valid for specimens with rectangular or round cross-section, cross-sectional area greater than 1 mm2 but less than 20 mm2, and a length not less than 10 nor more than 25 times the width or diameter.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
Server Error