EN 62841-3-6:2014/A1:2022
(Amendment)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system
2020-12-14: Common mods to this EN IEC are included in prAA (PR=73229) for simultaneous circulation
D164/C043: DOW=DOR+48 months
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 3-6: Besondere Anforderungen für transportable Diamantbohrmaschinen mit Flüssigkeitssystem
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-6: Exigences particulières pour les forets diamantés transportables avec système liquide
Električna motorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-6. del: Posebne zahteve za premične diamantne svedre s tekočinskim sistemom - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2022
Električna motorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost
- 3-6. del: Posebne zahteve za premične diamantne svedre s tekočinskim
sistemom - Dopolnilo A1
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills
with liquid system
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 3-6: Exigences particulières pour les forets diamantés transportables
avec système liquide
Ta slovenski standard je istoveten z: EN 62841-3-6:2014/A1:2022
ICS:
25.080.40 Vrtalniki Drilling machines
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 62841-3-6:2014/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM July 2022
ICS 25.140.20
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-6: Particular
requirements for transportable diamond drills with liquid system
(IEC 62841-3-6:2014/AMD1:2022)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-6: Exigences transportable Werkzeuge und Rasen- und
particulières pour les forets diamantés transportables avec Gartenmaschinen - Sicherheit - Teil 3-6: Besondere
système liquide Anforderungen für transportable Diamantbohrmaschinen
(IEC 62841-3-6:2014/AMD1:2022) mit Flüssigkeitssystem
(IEC 62841-3-6:2014/AMD1:2022)
This amendment A1 modifies the European Standard EN 62841-3-6:2014; it was approved by CENELEC on 2022-06-07. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-3-6:2014/A1:2022 E
European foreword
The text of document 116/575/FDIS, future IEC 62841-3-6/AMD1, prepared by IEC/TC 116 "Safety of
motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-3-6:2014/A1:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-05-16
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-05-16
document have to be withdrawn
extends the range for supply cords in Table 8.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association, and supports essential
requirements of EU Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZZ, which is an
integral part of EN 62841-3-6:2014/A12:2022.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62841-3-6:2014/AMD1:2022 was approved by CENELEC
as a European Standard without any modification.
IEC 62841-3-6 ®
Edition 1.0 2022-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 3-6: Particular requirements for transportable diamond drills with liquid
system
Outils électroportatifs à moteur, outils portables et machines pour jardins et
pelouses – Sécurité –
Partie 3-6: Exigences particulières pour les forets diamantés transportables
avec système liquide
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.140.20 ISBN 978-2-8322-5397-7
– 2 – IEC 62841-3-6:2014/AMD1:2022
© IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 3-6: Particular requirements for transportable
diamond drills with liquid system
AMENDMENT 1
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to IEC 62841-3-6:2014 has been prepared by IEC technical committee 116:
Safety of motor-operated electric tools.
The text of this Amendment is based on the following documents:
Draft Report on voting
116/575/FDIS 116/583/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
IEC 62841-3-6:2014/AMD1:2022 – 3 –
© IEC 2022
The language used for the development of this Amendment is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications/.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
___________
1 Scope
Replace the existing text with the following new text:
This clause of Part 1 is applicable, except as follows.
Replacement of the third paragraph:
The rated voltage is not more than 250 V for single-phase AC or DC tools, and 480 V for three-
phase AC tools.
Addition:
This document applies to transportable diamond drills, intended to be connected to a liquid
system. Liquid system can include liquid from a pipe or container.
2 Normative references
Replace the existing text with the following new text:
This clause of Part 1 is applicable, except as follows.
Replacement:
IEC 61540:1997 , Electrical accessories − Portable residual current devices without integral
overcurrent protection for household and similar use (PRCDs)
IEC 61540:1997/AMD1:1998
___________
There exists a consolidated edition 1.1:1999 which includes IEC 61540:1997 and its Amendment 1:1998.
– 4 – IEC 62841-3-6:2014/AMD1:2022
© IEC 2022
Addition:
IEC 61008-1:2010 , Residual current operated circuit-breakers without integral overcurrent
protection for household and similar uses (RCCBs) – Part 1: General rules
IEC 61008-1:2010/AMD1:2012
IEC 61008-1:2010/AMD2:2013
IEC 62841-1:2014, Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety – Part 1: General requirements
8 Marking and instructions
Delete the existing addition to 8.1.
Add the following new subclause:
8.3 Replacement of the sixth dash:
– ">25 kg" on each separable unit with a mass above 25 kg, in accordance with 8.14.2 a) 102).
Replace the existing text of 8.14.2 a), item 102), with the following new text:
102) Instruction to and information about how to mount the drill unit to the drill stand, if
separable;
Add the following new subclause:
8.14.3 Replacement:
If information about the mass or weight of the tool is provided, it shall either be the mass
specified in 5.17, or it shall be clear which part of the tool the mass refers to.
Compliance is checked by inspection.
14 Moisture resistance
Replace the existing text with the following new text:
This clause of Part 1 is applicable, except as follows.
14.3 Replacement:
Liquid systems or spillage of liquid shall not subject the user to an increased risk of electrical
shock.
If the tool is rated at least IPX4 in accordance with 14.2, this requirement is deemed to be
fulfilled.
___________
There exists a consolidated edition 3.2:2013 which includes IEC 61008-1:2010 and its Amendment 1:2012 and
Amendment 2:2013.
IEC 62841-3-6:2014/AMD1:2022 – 5 –
© IEC 2022
Compliance is checked by the following test:
The residual current device, if any, shall be disabled during the test. Electrical components,
covers and other parts which can be removed without the aid of a tool are removed, except
those fulfilling the test of 21.22.
The tool is prepared with approximately 1,0 % NaCl solution in the following modes if applicable:
– as described in 8.14.2;
– the liquid container of the tool is completely filled, and a further quantity, equal to 15 % of
the capacity of the container, or 0,25 l, whichever is the greater, is poured in steadily over
+0
a period of 60 s, while the tool is resting in its filling position in accordance with 8.14.2 d);
−10
– a detachable liquid container is filled completely and mounted and dismounted 10 times on
the tool.
In each applicable preparation, the tool is operated at rated voltage in each position consistent
with the instructions according to 8.14.2 b) for 1 min while monitoring the leakage current as in
Clause C.3.
For 3-phase diamond
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.