EN 62841-3-6:2014

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system (IEC 62841-3-6:2014, modified)

IEC 62841-3-6:2014 applies to transportable diamond drills, intended to be connected to a liquid system. The liquid system may include liquid from a pipe or container. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. This Part 3-6 is to be used in conjunction with IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Diamond drill, Drill unit, Drill stand

Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 3-6: Besondere Anforderungen für transportable Diamantbohrmaschinen mit Flüssigkeitssystem (IEC 62841-3-6:2014, modifiziert)

Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-6: Exigences particulières pour les forets diamantés transportables avec système liquide (IEC 62841-3-6:2014, modifiée)

L'IEC 62841-3-6:2014 s'applique aux forets diamantés transportables destinés à être connectés à un système liquide. Le système liquide peut inclure du liquide issu d'un tuyau ou d'un conteneur. La tension assignée est inférieure à 250 V pour les outils à courant monophasé alternatif ou continu, et inférieure à 480 V pour les outils à courant alternatif triphasé. La tension assignée est inférieure à 3 700 W. Les limites d'application de la présente Norme aux outils fonctionnant sur batterie sont indiquées dans l'annexe K. La présente Partie 3-6 doit être utilisée conjointement avec l'IEC 62841-1:2014. L'attention des Comités Nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 12 mois et au plus tard 36 mois après la date de publication. Mots-clés: Forets diamantes, unité de forage, support de forage

Električna motorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-6. del: Posebne zahteve za diamantne svedre s tekočinskim sistemom (IEC 62841-3-6:2014)

Standard EN IEC 62841-3-6 se uporablja za prenosne diamantne svedre, namenjene priključitvi na tekočinski sistem. Tekočinski sistem lahko vsebuje tekočino iz cevi ali vsebnika.

General Information

• Status: Published
• Publication Date: 21-Aug-2014
• Withdrawal Date: 20-Aug-2019
• ICS: 25.140.20 - Electric tools
• Technical Committee: CLC/TC 116 - Safety of hand-held motor-operated electric tools
• Drafting Committee: IEC/TC 116 - Safety of hand-held motor-operated electric tools
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 22-Aug-2014
• Completion Date: 22-Aug-2014
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 62841-3-6:2014 - Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 3-6: Particular requirements for diamond drills with liquid system

Relations

• Amended By: EN 62841-3-6:2014/A11:2017 - Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system
• Effective Date: 26-Jan-2023
• Amended By: EN 62841-3-6:2014/A12:2022 - Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system
• Effective Date: 26-Jan-2023
• Amended By: EN 62841-3-6:2014/A1:2022 - Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system
• Effective Date: 15-Dec-2020
• Corrected By: EN 62841-3-6:2014/AC:2015 - Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system (IEC 62841-3-6:2014, modified)
• Effective Date: 02-Jun-2015

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2014
1DGRPHãþD
SIST EN 61029-2-6:2010
(OHNWULþQDPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO3RVHEQH]DKWHYH]DGLDPDQWQHVYHGUHVWHNRþLQVNLPVLVWHPRP,(&

Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 3-6: Particular requirements for diamond drills with liquid
system
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 3-6: Règles particulières pour les forets diamantés transportables avec
système liquide
Ta slovenski standard je istoveten z: EN 62841-3-6:2014
ICS:
25.080.40 Vrtalniki Drilling machines
25.140.20 (OHNWULþQDRURGMD Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62841-3-6

NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2014
ICS 25.140.20 Supersedes EN 61029-2-6:2010
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-6: Particular
requirements for transportable diamond drills with liquid system
(IEC 62841-3-6:2014)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-6: Exigences transportable Werkzeuge und Rasen- und
particulières pour les forets diamantés transportables avec Gartenmaschinen - Sicherheit - Teil 3-6: Besondere
système liquide Anforderungen für transportable Diamantbohrmaschinen
(CEI 62841-3-6:2014) mit Flüssigkeitssystem
(IEC 62841-3-6:2014)
This European Standard was approved by CENELEC on 2014-05-02. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-3-6:2014 E
Foreword
The text of document 116/165/FDIS, future edition 1 of IEC 62841-3-6, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN 62841-3-6:2014.

A draft amendment, which covers common modifications to IEC 62841-3-6:2014, was prepared by
CLC/TC 116 "Safety of motor-operated electric tools" and approved by CENELEC.

The following dates are fixed:

• latest date by which this document has (dop) 2015-05-02
to be implemented at national level
by publication of an identical
national standard or by endorsement
• latest date by which the national (dow) 2018-05-02
standards conflicting with this document
have to be withdrawn
This document has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association, and supports essential requirements of
EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-3-6 are prefixed “Z”.

This European Standard is divided into four parts:

Part 1: General requirements which are common to most electric motor operated tools (for the
purpose of this standard referred to simply as tools) which could come within the scope of
this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
1)
This Part 3-6 is to be used in conjunction with EN 62841-1:201X . When this standard states "addition",
"modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.

Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101.

Compliance with the clauses of Part 1 together with this Part 3-6 provides one means of conforming with the
essential health and safety requirements of the Directive concerned.

Warning: Other requirements and other EU Directives can be applicable to the products falling within the
scope of this standard.
This European Standard follows the overall requirements of EN ISO 12100.

NOTE In this standard the following print types are used:
- requirements proper; in roman type
test specifications: in italic type;
-
- explanatory matter: in smaller roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun are
also in bold.
———————
1)
At draft stage.
- 3 - EN 62841-3-6:2014
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.

COMMON MODIFICATIONS
Replace the title of Annex I by the following:
Annex I
(normative)
Measurement of noise and vibration emissions

Add the following annex:
Annex ZZ
(informative)
Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all relevant
Essential Requirements as given in EU Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential requirements of
the Directives concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within the
scope of this standard.
___________
IEC 62841-3-6 ®
Edition 1.0 2014-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric motor-operated hand-held tools, transportable tools and lawn and

garden machinery – Safety –
Part 3-6: Particular requirements for transportable diamond drills with liquid

system
Outils électroportatifs à moteur, outils portables et machines pour jardins et

pelouses – Sécurité –
Partie 3-6: Exigences particulières pour les forets diamantés transportables

avec système liquide
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX Q
ICS 25.140.20 ISBN 978-2-8322-1540-1

– 2 – IEC 62841-3-6:2014 © IEC 2014
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 5
5 General conditions for the tests . 6
6 Radiation, toxicity and similar hazards . 6
7 Classification . 6
8 Marking and instructions . 6
9 Protection against access to live parts . 7
10 Starting . 7
11 Input and current . 7
12 Heating . 8
13 Resistance to heat and fire . 8
14 Moisture resistance . 8
15 Resistance to rusting . 8
16 Overload protection of transformers and associated circuits . 8
17 Endurance . 8
18 Abnormal operation . 9
19 Mechanical hazards . 9
20 Mechanical strength . 10
21 Construction . 10
22 Internal wiring . 11
23 Components . 11
24 Supply connection and external flexible cords . 11
25 Terminals for external conductors . 11
26 Provision for earthing . 11
27 Screws and connections . 11
28 Creepage distances, clearances and distances through insulation . 11
Annexes . 14
Annex I (informative) Measurement of noise and vibration emissions . 14
Annex K (normative) Battery tools and battery packs . 16
Bibliography . 17

Figure 101 – Example of a diamond drill with liquid system . 12
Figure 102 – Test arrangement to check efficiency of the liquid collection device . 13

Table 4 – Required performance levels . 9
Table I.101 – Test conditions for noise and vibration . 14
Table I.102 – Concrete formulation (per cubic metre) . 15
Table I.103 – Depth of holes for the test . 15

IEC 62841-3-6:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 3-6: Particular requirements for transportable
diamond drills with liquid system

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. Inter
...