prEN 50155:2024
(Main)Railway applications - Rolling stock - Electronic equipment
Railway applications - Rolling stock - Electronic equipment
This document is applicable to all electronic equipment for control, regulation, protection, diagnostic, energy supply, etc. installed on rail vehicles. For the purpose of this document, electronic equipment is defined as equipment composed of electronic components (e.g. resistors, capacitors, transistors, diodes, integrated circuits, hybrids, application specific integrated circuits, wound components and relays), and recognized associated components (e.g. connectors, mechanical parts). These components are mainly mounted on printed circuit boards. Sensors (e.g. current, voltage, speed) and semiconductor drive units for power electronic devices are covered by this document. Complete semiconductor drive units and power converters are covered by EN 61287-1. This document covers the requirements for operating conditions, design, documentation, testing and integration of electronic equipment, as well as hardware and software requirements considered necessary for compliant and reliable equipment. Specific requirements related to practices necessary to ensure defined safety integrity level or functional safety are not covered by this document. Nevertheless, this document is applicable to the hardware of all rolling stock electronic equipment or systems performing safety-related functions. The software development requirements for on-board railway equipment are specified by EN 50716.
Bahnanwendungen - Elektronische Einrichtungen auf Schienenfahrzeugen
Applications ferroviaires - Équipements électroniques utilisés sur le matériel roulant
Železniške naprave - Vozna sredstva - Elektronska oprema
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2024
Železniške naprave - Vozna sredstva - Elektronska oprema
Railway applications - Rolling stock - Electronic equipment
Bahnanwendungen - Elektronische Einrichtungen auf Schienenfahrzeugen
Applications ferroviaires - Équipements électroniques utilisés sur le matériel roulant
Ta slovenski standard je istoveten z: prEN 50155:2024
ICS:
45.060.01 Železniška vozila na splošno Railway rolling stock in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD DRAFT
prEN 50155
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2024
ICS 45.060.01 Will supersede EN 50155:2021
English Version
Railway applications - Rolling stock - Electronic equipment
Applications ferroviaires - Équipements électroniques Bahnanwendungen - Elektronische Einrichtungen auf
utilisés sur le matériel roulant Schienenfahrzeugen
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2024-11-29.
It has been drawn up by CLC/SC 9XB.
If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 76619 Ref. No. prEN 50155:2024 E
Contents Page
1 European foreword . 7
Introduction . 12
3 1 Scope . 13
4 2 Normative references . 13
5 Terms, definitions and abbreviations . 15
6 3.1 Terms and definitions . 15
7 3.2 Abbreviations . 21
8 General requirements . 22
9 4.1 Requirement for equipment characteristics. 22
10 4.2 Classes of environmental, constructional and service conditions . 22
11 Performance criteria . 22
4.3
12 4.3.1 General . 22
13 4.3.2 Performance criterion A . 23
14 Performance criterion B . 23
4.3.3
15 4.3.4 Performance criterion C . 23
16 4.4 Environmental service conditions . 23
17 Altitude . 23
4.4.1
18 4.4.2 Operating temperature . 23
19 4.4.3 Increased operating temperature at switch-on . 25
20 Rapid temperature variations . 25
4.4.4
21 4.4.5 Shock and vibration. 26
22 4.4.6 Electromagnetic compatibility . 26
23 Relative humidity . 26
4.4.7
24 4.5 Special service conditions . 27
25 4.5.1 General . 27
26 Atmospheric pollutants . 27
4.5.2
27 4.6 Installation requirements . 27
28 4.6.1 General . 27
29 Installation instructions . 27
4.6.2
30 4.6.3 Battery voltage supply system . 27
31 4.6.4 Thermal compatibility . 27
32 Electromagnetic compatibility . 27
4.6.5
33 4.6.6 Cabling inside vehicle . 28
34 4.6.7 Wiring inside equipment . 28
35 Insulation of the installation . 28
4.6.8
36 5 Electrical service conditions . 28
37 5.1 Typical supply systems .28
38 5.1.1 General .28
39 5.1.2 DC supply system .28
40 AC supply system .29
5.1.3
41 5.2 Battery voltage supply system .30
42 5.2.1 General .30
43 Supply voltage range .30
5.2.2
44 5.2.3 Temporary supply voltage variation .31
45 5.2.4 Interruption of supply voltage .31
46 Supply change-over .32
5.2.5
47 5.2.6 Grouping of supply voltages .32
48 5.2.7 DC ripple factor .32
49 Behaviour of system power supply during start of combustion engine .33
5.2.8
50 5.3 Supply by another source than the vehicle battery .33
51 5.3.1 Supply by a specific DC or AC source .33
52 Supply by an AC auxiliary power converter .33
5.3.2
53 5.3.3 Supply with overhead line or third rail .34
54 5.3.4 Design and test requirements for AC supply .34
55 Reliability, maintainability and expected useful life .34
56 6.1 Equipment reliability .34
57 6.1.1 Predicted reliability .34
58 Proof of reliability .34
6.1.2
59 6.2 Useful life .34
60 6.3 Maintainability .35
61 General .35
6.3.1
62 6.3.2 Preventive maintenance .35
63 6.3.3 Corrective maintenance .35
64 Built-in diagnostics .36
6.3.4
65 6.4 Automatic test equipment .36
66 6.5 Purpose-built test equipment and special tools .36
67 Design .36
68 7.1 General .36
69 7.1.1 Quality management .36
70 System life cycle model .37
7.1.2
71 7.2 Detailed practices - Hardware .37
72 7.2.1 Insulation coordination .37
73 Interfacing .37
7.2.2
74 7.2.3 Fault protection .38
75 7.2.4 Reference potential of power supplies .38
76 Interchangeability .39
7.2.5
77 7.2.6 Reduction of supply voltage and ON/OFF phases . 39
78 7.2.7 Reverse polarity protection . 39
79 7.2.8 Inrush currents . 39
80 Energetic transient pulses . 39
7.2.9
81 7.2.10 Capacitance to earth . 39
82 7.2.11 Spare capacity . 39
83 User Programmable Integrated Circuit . 39
7.2.12
84 7.3 Detailed practices - Software .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.