HD 631.3 S1:2008

Electric cables - Accessories - Material characterisation - Part 3: Fingerprinting for heat shrinkable components for medium voltage applications from 3,6/6 (7,2) kV up to 20,8/36 (42) kV

This Harmonization Document specifies the test methods and requirements for fingerprinting (as defined in 3.12) of heat shrinkable components intended to be used in cable accessories for medium voltage, as defined in HD 629.1 and HD 629.2. Fingerprinting of materials does not have a mandatory link to type testing of accessories. It shall be regarded as a stand-alone test, but may be carried out in combination with the accessory type tests. Component basic functions can be: conductive, stress control or stress grading, insulating, oil barrier, anti-tracking, external protection and sealing. Components are supplied as single layer items or as multi-layer items. NOTE Information on health and safety is given in Annex A.

Kabel und isolierte Leitungen - Garnituren - Materialcharakterisierung - Teil 3: Fingerprint-Prüfungen für wärmeschrumpfende Komponenten für Mittelspannungsanwendungen von 3,6/6 (7,2) kV bis 20,8/36 (42) kV

Dieses Harmonisierungsdokument legt die Bedingungen und Anforderungen für die Fingerprintprüfung (entsprechend 3.12) von wärmeschrumpfenden Komponenten für die Verwendung in Kabelgarnituren für Mittelspannung nach HD 629.1 und HD 629.2 fest. Fingerprintprüfungen an Werkstoffen sind nicht zwingend mit Typprüfungen von Garnituren verbunden. Sie müssen als eigenständige Prüfung betrachtet werden, dürfen aber auch in Kombination mit Typprüfungen von Garnituren durchgeführt werden. Die einzelnen Komponenten können im Wesentlichen leitfähige, feldsteuernde bzw. feldbegrenzende, isolierende, ölsperrende oder kriechstromfeste Eigenschaften haben sowie als äußerer Schutz und Abdichtung dienen. Die wärmeschrumpfenden Komponenten sind entweder einlagig oder mehrlagig ANMERKUNG Informationen zu Gesundheit und Sicherheit enthält Anhang A.

Câbles électriques - Accessoires - Caractérisation des matériaux - Partie 3: Essais d'identification des composants thermorétractables pour les applications moyenne tension de 3,6/6 (7,2) kV à 20,8/36 (42) kV

Le présent Document d’Harmonisation spécifie les méthodes et les exigences d’essai d’identification (tel que défini en 3.12) des composants thermorétractables destinés à être utilisés dans les accessoires moyenne tension, tels que définis dans le HD 629.1 et le HD 629.2. Les essais d’identification des matériaux n'ont aucun lien obligatoire avec les essais de type des accessoires. Ils doivent être considérés comme des essais indépendants mais ils peuvent être réalisés conjointement avec les essais de type des accessoires. Les fonctions principales des composants peuvent être: conducteur, contrôleur de champ ou répartiteur de tension, isolant, barrière vis-à-vis de l’huile, anti-cheminement, protection externe et étanchéité. Les composants sont fournis en articles mono couche ou en articles multi-couches. NOTE Des informations sur la santé et la sécurité sont données en Annexe A.

Električni kabli - Pribor - Značilnosti materialov - 3. del: Identifikacija materiala toplotno skrčljivih komponent za uporabo v srednjenapetostnih sistemih od 3,6/6(7,2) kV do vključno 20,8/36(42) kV

General Information

• Status: Withdrawn
• Publication Date: 23-Jul-2008
• ICS: 29.035.20 - Plastics and rubber insulating materials
• ICS: 29.060.20 - Cables
• Technical Committee: CLC/TC 20 - Electric cables
• Drafting Committee: IEC/TC 20 - IEC_TC_20
• Parallel Committee: IEC/TC 20 - IEC_TC_20
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 24-Jul-2008
• Completion Date: 24-Jul-2008
• Ref Project: SIST HD 631.3 S1:2009 - Electric cables - Accessories - Material characterisation -- Part 3: Fingerprinting for heat shrinkable components for medium voltage applications from 3,6/6 (7,2) kV up to 20,8/36 (42) kV

Relations

• Replaced By: EN 50655-2:2017 - Electric cables - Accessories - Material characterization - Part 2: Fingerprinting for heat shrinkable components for low and medium voltage applications up to 20,8/36 (42) kV
• Effective Date: 28-Nov-2017

Standards Content (Sample)

SLOVENSKI STANDARD
SIST HD 631.3 S1:2009
01-marec-2009
(OHNWULþQLNDEOL3ULERU=QDþLOQRVWLPDWHULDORYGHO,GHQWLILNDFLMDPDWHULDOD
WRSORWQRVNUþOMLYLKNRPSRQHQW]DXSRUDERYVUHGQMHQDSHWRVWQLKVLVWHPLKRG
N9GRYNOMXþQRN9
Electric cables - Accessories - Material characterisation -- Part 3: Fingerprinting for heat
shrinkable components for medium voltage applications from 3,6/6 (7,2) kV up to 20,8/36
(42) kV
Kabel und isolierte Leitungen - Garnituren - Materialcharakterisierung -- Teil 3:
Fingerprint-Prüfungen für wärmeschrumpfende Komponenten für
Mittelspannungsanwendungen von 3,6/6 (7,2) kV bis 20,8/36 (42) kV
Câbles électriques - Accessoires - Caractérisation des matériaux -- Partie 3: Essais
d'identification des composants thermorétractables pour les applications moyenne
tension de 3,6/6 (7,2) kV à 20,8/36 (42) kV
Ta slovenski standard je istoveten z: HD 631.3 S1:2008
ICS:
29.060.20 Kabli Cables
SIST HD 631.3 S1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST HD 631.3 S1:2009

---------------------- Page: 2 ----------------------

SIST HD 631.3 S1:2009

HARMONIZATION DOCUMENT
HD 631.3 S1

DOCUMENT D'HARMONISATION
July 2008
HARMONISIERUNGSDOKUMENT

ICS 29.035.20; 29.060.20


English version


Electric cables -
Accessories -
Material characterisation -
Part 3: Fingerprinting for heat shrinkable components
for medium voltage applications from 3,6/6 (7,2) kV up to 20,8/36 (42) kV



Câbles électriques -  Kabel und isolierte Leitungen -
Accessoires - Garnituren -
Caractérisation des matériaux - Materialcharakterisierung -
Partie 3: Essais d'identification Teil 3: Fingerprint-Prüfungen
des composants thermorétractables für wärmeschrumpfende Komponenten
pour les applications moyenne tension für Mittelspannungsanwendungen
de 3,6/6 (7,2) kV à 20,8/36 (42) kV von 3,6/6 (7,2) kV bis 20,8/36 (42) kV





This Harmonization Document was approved by CENELEC on 2008-06-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for implementation of this
Harmonization Document at national level.

Up-to-date lists and bibliographical references concerning such national implementations may be obtained on
application to the Central Secretariat or to any CENELEC member.

This Harmonization Document exists in three official versions (English, French, German).

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. HD 631.3 S1:2008 E

---------------------- Page: 3 ----------------------

SIST HD 631.3 S1:2009
HD 631.3 S1:2008 - 2 -
Foreword
This Harmonization Document was prepared by a task force under the direction of WG 11 of CENELEC
TC 20, Electric cables.
As agreed at the Bruges meeting (June 2007), the text of the draft was submitted to the formal vote and
was approved by CENELEC as HD 631.3 S1 on 2008-06-01.
The following dates were fixed:
- latest date by which the existence of the HD
has to be announced at national level (doa) 2008-12-01
- latest date by which the HD has to be implemented
at national level by publication of a harmonized
national standard or by endorsement (dop) 2009-06-01

- latest date by which the national standards conflicting
with the HD have to be withdrawn (dow) 2011-06-01
HD 631 will have 4 parts:
Part 1: Fingerprinting and type tests for resinous compounds
Part 2: Fingerprinting and type tests for heat shrinkable components for low voltage applications
Part 3: Fingerprinting for heat shrinkable components for medium voltage applications from
3,6/6 (7,2) kV up to 20,8/36 (42) kV
Part 4: Fingerprinting for cold shrinkable components for low and medium voltage applications up to
20,8/36 (42) kV
Fingerprinting of sealant components which are delivered as non heat shrinkable items, but that have an
important interfacing role, is under consideration.
NOTE  It has been assumed in the preparation of this document that the execution of its provisions will be entrusted to
appropriately qualified and experienced people, for whose use it has been produced.
WARNING  This Harmonization Document calls for the use of substances and/or procedures that may be
injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not
absolve the user from legal obligations relating to health and safety at any stage.
_____________

---------------------- Page: 4 ----------------------

SIST HD 631.3 S1:2009
 - 3 - HD 631.3 S1:2008
Contents

1 Scope . 4
2 Normative re f e r enc es . 4
3 Terms and definitions . 4
4 Fingerprinting . 6
4.1 General . 6
4.2 Sampling . 6
4.3 Preparation and conditioning . 6
4.4 Tests . 6
4.5 Test report . 6
Annex A (informative) Health and safety . 8
Annex B (normative) Dimensions after full recovery . 9
Figure B.1 . 9
Table 1 – Test methods and requirements . 7

---------------------- Page: 5 ----------------------

SIST HD 631.3 S1:2009
HD 631.3 S1:2008 - 4 -
1 Scope
This Harmonization Document specifies the test methods and requirements for fingerprinting (as
defined in 3.12) of heat shrinkable components intended to be used in cable accessories for
medium voltage, as defined in HD 629.1 and HD 629.2.
Fingerprinting of materials does not have a mandatory link to type testing of accessories. It shall
be regarded as a stand-alone test, but may be carried out in combination with the accessory type
tests.
Component basic functions can be: conductive, stress control or stress grading, insulating, oil
barrier, anti-tracking, external protection and sealing. Components are supplied as single layer
items or as multi-layer items.
NOTE Information on health and safety is given in Annex A.
2 Normative references
The following referenced documents are indispensable for the application of this document.
...

6/29(16., R6,67SU+'6

35('67$1'$5'
GHFHPEHU
(OHNWULþQLNDEOL±3ULERU±=QDþLOQRVWLPDWHULDORY±GHO)LQJHUSULQWLQJ]D
WRSORWQRVNUþOMLYHVHVWDYQHGHOH]DXSRUDERYVUHGQMHQDSHWRVWQLKVLVWHPLKRG
N9GRYNOMXþQRN9
(OHFWULFFDEOHV$FFHVVRULHV0
...