iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

HD 280.3 S1:1990

(Main)

Safety requirements for electric fans and regulators - Part 3: Jet fans

Safety requirements for electric fans and regulators - Part 3: Jet fans

Safety of Household and Similar Electrical Appliances, Part 1 : General Requirements, is applicable except as follows: 1.1 Replacement: This standard applies to jet fans commonly known as air circulators and air blast cooling fans oscillating and non-oscillating and their associated regulators intended for use on single phase a.c. circuits and d.c. circuits not exceeding 250 V ; air blast cooling fans may be intended for use on three phase a.c. system up to 440 V. Wherever applicable, the term "fan" used in this standard includes its associated regulators, if any. Provisions of this standard may also be adapted to the extent applicable to fans not intended for normal household use, which nevertheless may be a source of danger to the public. Additional requirements may also be necessary for fans intended to be used in: i) vehicles, and ii) tropical countries. Attention is drawn to the fact that in many countries additional requirements may be specified by the national health authorities and the national authorities responsible for protection of labour. This standard does not apply to safety requirements for jet fans intended to be used in locations where special conditions prevail, such as the presence of corrosive or explosive atmosphere. 1.2 Addition: Jet fans and does not cover performance. This standard is concerned with safety requirements of jet fans and requirements and corresponding tests which are covered in IEC Publication 535: Regulators.

Sicherheitsanforderungen für Ventilatoren und zugehörige Steuereinheiten - Teil 3: Strahlventilatoren

Règles de sécurité pour les ventilateurs électriques et leurs régulateurs de vitesse - Partie 3: Ventilateurs de jet

Safety requirements for electric fans and regulators - Part 3: Jet fans (IEC 60342-3:1982)

General Information

Status
Withdrawn
Publication Date
19-Sep-1990
Technical Committee
CLC/TC 61 - Safety of household and similar electrical appliances
Drafting Committee
IEC/TC 61 - IEC_TC_61
Parallel Committee
IEC/TC 61 - IEC_TC_61
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Apr-2000
Completion Date
01-Apr-2000
Directive
2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
73/23/EEC - Electrical equipment designed for use within certain voltage limits
Ref Project
SIST HD 280.3 S1:1999 - Safety requirements for electric fans and regulators -- Part 3: Jet fans

Relations

Replaced By
EN 60335-2-80:1997 - Safety of household and similar electrical appliances - Part 2-80: Particular requirements for fans
Effective Date
29-Jan-2023

Buy Standard

HD 280.3 S1:1999HD 280.3 S1:1999
PreviousNext
Standardization document
HD 280.3 S1:1999
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST HD 280.3 S1:1999
01-julij-1999
Safety requirements for electric fans and regulators - Part 3: Jet fans (IEC 60342-
3:1982)
Safety requirements for electric fans and regulators -- Part 3: Jet fans
Sicherheitsanforderungen für Ventilatoren und zugehörige Steuereinheiten -- Teil 3:
Strahlventilatoren
Règles de sécurité pour les ventilateurs électriques et leurs régulateurs de vitesse --
Partie 3: Ventilateurs de jet
Ta slovenski standard je istoveten z: HD 280.3 S1:1990
ICS:
23.120 =UDþQLNL9HWUQLNL.OLPDWVNH Ventilators. Fans. Air-
QDSUDYH conditioners
SIST HD 280.3 S1:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST HD 280.3 S1:1999

---------------------- Page: 2 ----------------------

SIST HD 280.3 S1:1999

---------------------- Page: 3 ----------------------

SIST HD 280.3 S1:1999

---------------------- Page: 4 ----------------------

SIST HD 280.3 S1:1999

---------------------- Page: 5 ----------------------

SIST HD 280.3 S1:1999

---------------------- Page: 6 ----------------------

SIST HD 280.3 S1:1999

---------------------- Page: 7 ----------------------

SIST HD 280.3 S1:1999

--
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60383-1:2023(Main)
Insulators for overhead lines with a nominal voltage above 1 000 V - Part 1: Ceramic or glass insulator units for a.c. systems - Definitions, test methods and acceptance criteria
kSIST FprEN IEC 60383-1:2023

This part of IEC 60383 applies to insulators of ceramic material or glass for use on a.c. overhead power lines and overhead traction lines with a nominal voltage greater than 1 000 V and a frequency not greater than 100 Hz. It also applies to insulators for use on d.c. overhead electric traction lines. This part applies to string insulator units, rigid overhead line insulators and to insulators of similar design when used in substations. lt does not apply to insulators forming parts of electrical apparatus or to parts used in their construction or to post insulators which are covered by IEC 60168: Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 000 V. Tests on insulator strings and insulator sets (for example, wet switching impulse voltage) are dealt with in part 2 of IEC 60383. The object of this part is: - to define the terms used - to define insulator characteristics and to prescribe the conditions under which the specified values of these characteristics shall be verified - to prescribe test methods - to prescribe acceptance criteria. This part does not include requirements dealing with the choice of insulators for specific operating conditions. Specific requirements on the use of coatings on ceramic or glass insulators are described in the informative Annex C. NOTE A guide for the choice of insulators under polluted conditions has been published, see IEC 60815-1 and -2. Numerical values for insulator characteristics are specified in IEC 60305, IEC 60433 and IEC 60720.

  • Draft
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62149-3:2023(Main)
Fibre optic active components and devices - Performance standards - Part 3: Modulator-integrated laser diode transmitters for 40-Gbit/s fibre optic transmission systems
oSIST prEN IEC 62149-3:2023
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63281-1:2023(Main)
E-Transporters - Part 1: Terminology and classification
kSIST FprEN IEC 63281-1:2023
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-2-26:2023(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-26: Tests - Salt mist
kSIST FprEN IEC 61300-2-26:2023

D133/C027: for all CLC/TC 86BXA revisions of standards, the dow is set to dow= dor + 12 months

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60793-1-44:2023(Main)
Optical fibres - Part 1-44: Measurement methods and test procedures - Cut-off wavelength
kSIST FprEN IEC 60793-1-44:2023

IEC 60793-1-44:2023 establishes uniform requirements for measuring the cut-off wavelength of single-mode optical fibre, thereby assisting in the inspection of fibres and cables for commercial purposes. This document gives methods for measuring the cut-off wavelength for uncabled or cabled single mode telecom fibre. These procedures apply to all category B and C fibre types. There are three methods of deployment for measuring the cut-off wavelength: - method A: cable cut-off using uncabled fibre 22 m long sample, lcc; - method B: cable cut-off using cabled fibre 22 m long sample, lcc; - method C: fibre cut-off using uncabled fibre 2 m long sample, lc. All methods require a reference measurement. There are two reference-scan techniques, either or both of which can be used with all methods: - bend-reference technique; - multimode-reference technique using category A1(OM1-OM5) multimode fibre. This third edition cancels and replaces the second edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) used the diameter of the fibre loops to describe deployment; b) added Annex D related to cut-off curve artifacts; c) reorganized information and added more figures to clarify concepts.

  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62044-3:2023(Main)
Cores made of soft magnetic materials - Measuring methods - Part 3: Magnetic properties at high excitation level
oSIST prEN IEC 62044-3:2023
  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61300-3-45:2023(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-45: Examinations and measurements - Attenuation of random mated multi-fibre connectors
SIST EN IEC 61300-3-45:2023

IEC 61300-3-45:2023 is available as IEC 61300-3-45:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61000-3-45:2023 describes the procedure required to measure the statistical distribution and mean attenuation for random mated optical connectors with physical contact (PC) and angled physical contact (APC) polished multi-fibre rectangular ferrules as defined in the IEC 61754 series. This measurement method is applicable to cable assemblies. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of sample size for > 12-fibre connector measurement; b) inclusion of guidance for multimode measurement.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60127-2:2014/A1:2023(Amendment)
Miniature fuses - Part 2: Cartridge fuse-links
SIST EN 60127-2:2015/A1:2023

NEXT ACTION: HAS CONSULTANT ASSESSMENT BY 2020-01-29
2020-07-06 link to LVD added, asked SR for ZZ and ZA

  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63300:2023(Main)
Test methods for electrical and magnetic properties of magnetic powder cores
oSIST prEN IEC 63300:2022

This standard provides the test methods for the electrical and magnetic properties of magnetic powder cores used for inductive components in electronics equipment, switch-mode power supplies and power conversion equipment, and introduces measuring principles, scope of application and matters needing attention for each method. The parameters used to characterize the magnetic powder cores include: inductance factor, effective permeability, complex relative permeability, temperature coefficient of permeability, frequency coefficient of permeability, DC bias characteristic, power loss, and quality factor. This standard is the basis for determining the characteristic parameters of magnetic powder cores.

  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50360:2017/A1:2023(Amendment)
Product standard to demonstrate the compliance of wireless communication devices, with the basic restrictions and exposure limit values related to human exposure to electromagnetic fields in the frequency range from 300 MHz to 6 GHz: devices used next to the ear
SIST EN 50360:2018/oprA1:2020

This product standard applies to wireless communication devices used in close proximity to the human ear (e.g. mobile phones, wireless headsets). The applicable frequency range is from 300 MHz to 6 GHz. The objective of this standard is to demonstrate the compliance of such devices with the basic restrictions and exposure limit values related to human exposure to radio frequency electromagnetic fields. For devices used next to the body or in front of the face the applicable product standard is EN 50566:2017. For low power devices the applicable product standard is EN 50663:2017.

  • Draft
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day